This comparison covers selected direct-injection (DI) upgrades and supplementary or replacement multi-port injection (MPI) parts for the 2.0 TFSI EA113 and specified 1.8/2.0 TSI/TFSI EA888 engines. It is not a universal interchange list. Confirm engine code, market, original injector and connector, manifold, fuel, ECU software and tuner support with the supplier. Part numbers and availability can change.
Reading injector specifications
DI injectors deliver fuel into the combustion chamber from the high-pressure rail. MPI injectors deliver into the intake port using a separate low-pressure fuel circuit; some vehicles have factory MPI and others need a manifold, rail, wiring and control strategy to add it. A 980 cc/min port injector rated at 3 bar cannot be compared directly with a direct injector rated at 100 bar. Flow figures depend on the test liquid, pressure difference and method; mass flow, volume flow, static flow and fuel-system power estimates are different quantities. Injector diameter alone does not define spray targeting, electrical compatibility, opening and closing behaviour or safe engine power.
Relative gains are supplier claims against different original injectors, and some suppliers do not publish the pressure, test fluid or measurement method. Those percentages must not be treated as a common ranking. Figures below are per injector unless the listing describes a kit. Supplier power estimates are fuel-capacity estimates for a stated combination, not a guarantee that a complete car can safely achieve them.
EA113 2.0 TFSI direct-injector examples
| Make and part | Application and published specifications | Contents and calibration |
|---|---|---|
| APR / Bosch MS100041 | Four Bosch HDEV1 injectors, VAG 06F 906 036 F. APR lists these as original equipment on selected higher-output EA113 engines and an upgrade for specified lower-output K03 models. APR claims approximately 13% more flow than its K03 baseline; it does not state an absolute rate or test pressure on this listing. | Set of four; matching software required. Verify engine and original injector: a factory K04 engine may already use this injector, so it is not automatically an upgrade for that car. |
| Nostrum H720-1748 | EA113 HDEV1-outline direct injector. Nostrum quotes 17.9 g/s with Viscor 16A and 1,484 cc/min with n-heptane, each at 100 bar static, and 40% over its Mk6 Golf R baseline of 12.79 g/s. E85 compatible; 180 bar maximum recommended operating pressure. | Supplied preassembled with EA113 seals, backing rings, harness adapters and spacers. Custom calibration required. The maker says operation above the original 130 bar relief pressure requires fuel-rail pressure-relief changes; its injector pressure rating alone does not approve raising the complete system pressure. |
| AKS Tuning AKSHFI002 Mk2 | Modified new VAG 06F 906 036 F injectors in matched sets for the supplier's transverse EA113 applications. AKS claims approximately 47% above K03 and 31% above K04 injectors; the listing does not publish absolute flow, test pressure or fluid. | Four injectors with seals, clips and baskets; AKS requires custom mapping and says standard K03/K04 maps are unsuitable. Confirm current part specification and fitment with the manufacturer. |
| BAR-TEK RSX 21tf055 | Supplier's EA113 2.0 TFSI upgrade kit; BAR-TEK claims approximately 30% more flow than its RS3 comparison and up to 600 hp at 130 bar. Test fluid and complete test conditions are not stated; treat its power figure as a vendor claim. | Four matched injectors with adapter plugs. Remapping and verification are required; confirm the exact engine and hardware against the supplier before purchase. |
Names such as “RS4 injectors” do not uniquely establish a part or flow. For example, a supplier identifies 079 906 036 AB with the B7 RS4/R8 4.2 FSI, but the listing does not establish a universal EA113 installation or publish a test flow. Identify the donor engine and exact part revision, mounting, seals, connector and calibration instead of ordering by nickname.
EA888 Gen 1 and Gen 2 direct-injector examples
| Make and part | Application and published specifications | Contents and calibration |
|---|---|---|
| Nostrum H720-1517 | Supplier's selected Gen 1/2 2.0 TSI/ TFSI applications, including listed CCTA, CBFA and CAEB vehicles. 17.9 g/s Viscor 16A or 1,484 cc/min n-heptane at 100 bar; maker claims 46% above its Mk6 GTI stock reference, with 200 bar maximum operating pressure. | Four direct injectors; Nostrum describes its listed applications as direct fit without harness adapters or spacers. Tuning is required and injector data are available to the calibrator. An older Nostrum catalogue calls out H620-1395 for a Gen 1/2 high-flow injector; verify the current replacement part with Nostrum rather than assuming the numbers are interchangeable. |
| BAR-TEK RSX 21tf195 | Four Bosch-based injectors for listed 2.0 TSI applications. BAR-TEK claims about 40% more than its OEM reference; absolute flow, test pressure and fluid are not published. Its application list includes different engine codes, so check the exact original parts. | Remap required. Check contents, injector electrical connection and supplier fitment for the individual engine. |
| Bosch / Stratified 06L 906 036 AK | Four Mk7 Golf R direct injectors; Stratified also lists a Gen 1 2.0 GTI application and claims 15.7% more fuelling headroom against its Gen 1 reference. Its test conditions and absolute flow are not stated. | Supplier requires tuning. Its listed cross-generation application does not prove compatibility with every Gen 1 or Gen 2 engine; confirm hardware and injector characterisation with the supplier and tuner. |
EA888 Gen 3 and Evo4: direct and port injection
| Make and part | Type, application and published specifications | Contents and calibration |
|---|---|---|
| Bosch / Stratified 06L 906 036 AK | Direct injection, Golf R-based set for listed Gen 3 1.8 and 2.0 engines. Stratified claims 9.2% more fuelling headroom versus its non-R 2.0 reference, or 24.5% versus its 1.8 reference; absolute flow and test conditions not stated. | Set of four; tuning required. Verify the injector already fitted to the recipient, as a Golf R may already have the same type. |
| BAR-TEK 21tsi194 | Four matched Bosch Golf R-type Gen 3 direct injectors; BAR-TEK claims approximately 40% more flow versus its smaller IS20-engine reference. Absolute flow and test conditions not stated. | Supplier requires remapping. Its listing does not establish that these are part 06L 906 036 AK. BAR-TEK and Stratified use different stated comparisons and their claims must not be equated or combined. |
| APR MS100229 MPI system | Supplementary port injection, not a DI replacement. Four Bosch Motorsport EV14 0 280 158 040 injectors rated 980 cc/min each; APR's separate injector specification identifies 3 bar, n-heptane, 12 ohm coil and up to 8 bar. APR lists selected Gen 3 and 2022–24 Mk8 Golf R/8Y S3 Gen 4 applications; do not assume every Evo4 GTI fits. | Four injectors, rail, sensor, wiring harness and distribution block; check current contents. APR requires matching Stage 3+ ECU/TCU software and a compatible APR turbocharger system. Low-pressure supply must support the full system; the kit listing does not establish that a fuel pump is included. |
| APR MS100195 / Bosch 0 280 158 040 | One port injector and adapter: 980 cc/min, 670 g/min or 89 lb/hr at 3 bar with n-heptane. APR also quotes 12 ohms, 30-degree cone and 8 bar maximum. It states E85/M100 compatibility. | Sold as one injector with harness, not a four-injector system. APR specifies compatible Gen 3 models with factory MPI and appropriate software; non-MPI cars require more components. Verify manifold and connector. APR specifies flushing after methanol use. |
| Unitronic Gen 3 MQB MPI kit | Supplementary port-injection kit for the supplier's selected 1.8 and 2.0 EA888 Gen 3 MQB vehicles. Unitronic lists four Bosch Motorsport 980 cc injectors; pressure and test fluid are not given on its announcement. | Includes a fuel rail and hardware for the specified North American manifold; MPI-capable calibration and suitable low-pressure delivery must be arranged. Check the current product listing for exact contents and vehicle fitment. |
| Injector Dynamics ID1300-XDS | Port injector; manufacturer lists nominal 1,335 cc/min at 3.0 bar with isooctane at 52 °C, 7 bar maximum differential pressure and USCAR connector. Its fitment table identifies separate VW and Audi EA888 Gen 3 sets, including 1300.34.14.14.4 for VW. | Check the actual intake manifold, rail, injector length, electrical connection and set part number with the supplier. Injector Dynamics' page body uses an ID1300x² label as well as the ID1300-XDS title; confirm the data and part revision before ordering. MPI hardware and compatible calibration are required. |
For an early EA113 or EA888 auxiliary port system, Integrated Engineering's port-injection manifold kit lists compatible EV14-format injectors with its separately specified rail, but does not include the injectors, lines or controller. It describes the setup for racing; verify the equipment and use restrictions for the intended car. It supplements the original DI system.
No flow-rated Evo4 direct-injector replacement with verified manufacturer-supported fitment was established in this research. The listed Evo4 APR system adds port injectors; do not assume Gen 3 direct-injector swaps fit Evo4.
Installation and calibration checks
- Choose the fuel and power target with a calibrator first. Record exact engine and ECU identity, DI and any MPI injector numbers, hardware revision and the supplier's characterisation data.
- For DI, obtain correct flow-versus-pressure, opening/closing or offset, short-pulse and injection-window data for the actual ECU and injector. Confirm spray pattern, seating, seals, retaining hardware and connector; do not assume a physically fitting injector has suitable spray or calibration. See MED9.1 injector calibration and injection windows for a documented EA113 example.
- For MPI, identify whether it is already fitted, how it will be controlled and blended with DI, and whether a suitable manifold, rail, pressure regulation, wiring and software are supplied. Injector size alone does not provide a control strategy.
- Match both low-pressure supply and HPFP to the actual fuel and demand. Larger injectors do not repair a pressure-starved pump; an uprated pump does not cure a restricted injection window. See the HPFP and LPFP comparison.
- Follow vehicle-specific repair instructions and the supplier's seal, cleaning and pressure-release procedures. Under controlled testing, review requested versus actual rail and low-side pressure, commanded and measured lambda, corrections, misfires and the available injector timing and pulse information. Confirm safe pressure limits for every component; avoid transferring limits from one supplier's system to another.
Manufacturer and supplier listings reviewed 17 November 2026. Product availability, claimed specifications and calibration support may change. Consult the linked current listings and vehicle-specific repair information.
Earlier 1.8T 20V: For its original port injectors and electric fuel-pump upgrades, see the 1.8T injector and fuel-pump guide. Fitment and injector calibration differ from the later direct-injection engines covered here.