Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Turbocharging
Parent
Section level
Applies to
Bosch MED17.5
Tool groups
None
Manufacturers
Volkswagen Group

Scope: 2.0-litre EA888 generation 1 and 2 examples with direct injection, including transverse VW/Audi installations and longitudinal Audi CAEB examples. These products are examples from manufacturers, not a universal fitment list. The 1.8-litre EA888, EA113 and later EA888 generations need their own parts and calibration checks. Record VIN, market, year, engine code, transmission, original turbo part number and ECU hardware/software identification before ordering.

See the EA888 Gen 1, EA888 Gen 2 and Bosch MED17.5 pages. VW's SSP 824803 identifies a 147 kW CCTA/CBFA example and MED17.5; Audi's SSP 922903 identifies the CAEB and MED17.5. These examples do not prove the exact ECU for every kit application.

From around 200 hp to over 300 hp

For a documented transverse 2.0T Gen 1 example, APR's calibration report lists a 200 PS factory figure, its own stock measurement of 221 hp and K04 results of 346 hp on 91 AKI/95 RON or 360 hp on 93 AKI/98 RON, with the specified supporting hardware and software. These are APR's test results, not guaranteed results or a promise of exactly 300 hp; its report also lists peak gains, which are not simply the difference between its listed peak figures. The fuel grades use US AKI and European RON scales. Select the calibration for the fuel actually available and never use fuel below its required rating.

A higher-output car is a useful comparison, but fitting its unmodified turbo does not convert the whole engine into a Golf R or S3 engine. APR and Turbo Technics describe K04-based units adapted to the recipient installation, including a diverter-valve mounting arrangement. Turbo Technics explicitly describes some recipients as originally IHI-equipped; CTS also lists original IHI and BorgWarner arrangements. Verify the original part rather than assuming every early EA888 is K03-equipped, or that all K04 castings, outlets, lines and calibrations interchange.

Turbocharger and kit examples

Figures below are supplier claims for their stated combinations. They use different fuels, supporting parts and measurement methods; do not compare them as guaranteed equivalent outputs. Check current availability and exact fitment with each supplier.

Manufacturer and partApplication and specificationsSupplied items, requirements and claimed output
APR K04-64, T2100016Transverse 2.0T EA888 Gen 1. APR lists selected 2008–2014 GTI and other specified models; confirm engine, market and ECU box code. Customised K04-64 with integrated diverter-valve mount and 3-bar Bosch MAP sensor.Includes fitting hardware and APR Stage 3 K04 ECU software; dealer installation and software compatibility check required. APR specifies intake, intercooler, transmission software, race downpipe and the specified spark plugs, and notes that some cars may need valve springs, internal or transmission upgrades. Its calibration report gives 346/360 hp at 95/98 RON respectively. Its listed race downpipe has restricted permitted use: establish a compliant solution for the vehicle's intended use with the calibration provider.
Turbo Technics S263Supplier's 2.0 TSI/TFSI EA888 Gen 1 listing, 2008–2013, engine codes CAWB, CCZA and CCZB. K04/K06 hybrid with billet K06-spec compressor, larger K04 turbine and modified outlet with integrated diverter mount.Up to 360 bhp capability claimed, with remap, intake, intercooler and full turbo-back exhaust as its minimum supporting modifications. Fitting kit includes exhaust studs/nuts, drain gasket and boost hose/clips. Fuel hardware and software are not specified as included; confirm them for the planned calibration.
BAR-TEK V1 K04 kit, 22tsi01Supplier identifies IHI-equipped 2.0 TSI CAWB, CCZA and CCZB, such as the Mk6 GTI 211 hp. Modified K04 upgrade; vendor claims up to 400 hp engine power.Vendor lists turbo, power/boost pipes, diverter adapter and valve, wiring, gaskets and fasteners. For its 400 hp combination it specifies RSX injectors, upgraded HPFP, intercooler, downpipe and Milltek exhaust, and recommends valve springs. A separate BAR-TEK listing for 22tsi01 states software is not included. Check the exact kit contents and software with the seller.
CTS K04 longitudinal upgradeCTS lists selected B8/B8.5 A4, A5, Allroad and Q5 2.0T applications, as well as earlier B7 cars. K04 centre assembly with CTS housings and a 46.38/56.1 mm machined compressor wheel; supplied with fitting hardware.CTS claims 350 hp/340 lb-ft with supporting modifications. K04-specific ECU tuning and a suitable high-flow catalytic converter are stated as required; intake and intercooler are recommended. It explicitly calls for upgraded HPFP and injectors on the B7: do not transfer that requirement automatically to every B8 EA888. CTS notes coolant-line bracket trimming can be necessary. Check the engine code, exact vehicle and calibration because its listing spans multiple engine families.

What the conversion involves

  1. Choose a matched package. Confirm manifold/turbine flange, exhaust connection, compressor outlet and intake, oil and coolant lines, wastegate actuator and control, diverter valve and wiring, sensors and fitting seals for the actual engine bay. A direct-fit turbo can still need separately supplied pipework or software. The APR and Turbo Technics product descriptions above show different included hardware and requirements.
  2. Use matching ECU software. A K04 changes the airflow and boost-control response. Arrange a calibration for the exact ECU software, turbo, pressure sensor, fuel, injectors and hardware. APR includes compatible dealer-installed software with its kit; Integrated Engineering separately offers a K04 calibration for listed transverse EA888 Gen 1/2 cars and says its tune requires an upgraded downpipe and intercooler, DSG tune on DSG applications or clutch upgrade on manuals. Confirm ECU box-code and non-US market support before buying.
  3. Plan fuel supply for the actual target. Neither a universal HPFP/LPFP change nor an unchanged stock fuel system is justified from a turbo name alone. BAR-TEK calls for an upgraded high-pressure pump and injectors for its 400 hp build; CTS's B7 pump/injector note is specific to that application. Confirm low-side supply, high-pressure rail performance and injector capacity with the calibration provider, especially for ethanol blends. An in-tank LPFP and cam-driven HPFP have different jobs; neither quoted turbo power nor a free-flow pump figure establishes the safe capacity of the complete system.
  4. Manage temperature and driveline torque. Fit the intake, intercooler, exhaust and plugs required by the chosen package. Check clutch, gearbox and transmission software capacity; stronger springs or engine parts may be needed for the particular rpm and load. APR explicitly flags valve float and offers lower-torque software for some applications. A vendor's exhaust requirement and local emissions approval are separate questions: check both before purchase.
  5. Verify the car. Resolve faults and mechanical issues first, follow the kit's installation/priming instructions, and check for oil, coolant, intake and exhaust leaks. With appropriate safe testing, compare boost request and actual with the same pressure units and reference, rail-pressure request and actual, lambda request and measured response, intake temperature, ignition correction, throttle and wastegate control. Record fuel and conditions; investigate persistent deviation rather than increasing boost to chase a headline figure. See fuel-pressure and lambda log review and boost-control diagnosis.

Manufacturer figures and parts lists reviewed 17 November 2026. Product specifications and calibration support can change; confirm against the linked current listings and vehicle-specific repair information.

For component makes, part numbers and published pump specifications, see the EA113 and EA888 HPFP/LPFP upgrade comparison.

For high-flow direct injectors and supplementary port-injection options, see the EA113 and EA888 injector upgrade comparison; follow the selected turbo calibration’s specific fuelling requirements.