Tuning Wiki
Applies to

Check the hardware and software limits stated in this article.

Scope: “Generation 2” is a convenient label used for later early-EA888 variants; market, installation and changes overlap. This page uses the specifically identified Audi 2.0 TFSI CAEB as an example, not a complete fitment list. Verify the engine code, market, vehicle, build date and ECU before applying any detail to another engine.

Engine and ECU identification

Audi SSP 922903, printed pp. 1–3, identifies its CAEB engine as a 1,984 cc inline-four direct-injection turbo engine with 82.5 × 92.8 mm bore and stroke and Bosch MED17.5 engine management. The same document describes a cast-iron block, chain-driven timing gear, balance shafts and four valves per cylinder. The generation label alone does not establish an exact MED17 subvariant, part number, software, calibration or vehicle fitment.

Audi's 2013 oil-consumption bulletin identifies specific CAEB examples in 2009–2011 A4, A5 and Q5 applications and lists multiple ECU software part numbers. The training document and service material show why a vehicle badge alone is insufficient: retain VIN, engine code, ECU part number and software version with a read or log. Use current manufacturer information for the particular car.

Vehicles fitted with documented examples

These are sourced examples of early longitudinal EA888 applications, not a complete worldwide fitment list. An engine can change within the same model and model year. The Audi U.S. service bulletin 17 13 43 directly associates the CAEB engine and the following vehicles:

VehicleExample engine and periodEvidence and scope
Audi A4, B82.0 TFSI CAEB: U.S. model years 2009–2011.Audi's 2013 bulletin lists CAEB and the covered A4 model years. This is the bulletin's scope, not the engine's complete production range.
Audi A5 and A5 Cabriolet, B82.0 TFSI CAEB: U.S. model years 2010–2011.The bulletin separately identifies A5 and A5 Cabriolet CAEB examples.
Audi Q5, 8R2.0 TFSI CAEB: U.S. model year 2011.The same Audi bulletin lists its 2011 CAEB Q5 example; other years and markets need separate verification.
Audi A4 / A4 Avant, 8K2 / 8K52.0 TFSI CAEA / CDNB / CFKA, 132 kW; CAEB / CDNC, 155 kW.Schaeffler LuK July 2019 application list groups these codes for selected 0AW CVT applications. It gives June 2008–December 2015 for the first group and June 2008–May 2013 for the second. These are catalogue ranges for grouped vehicle types, not proof every code was fitted throughout every month.
Audi A5, 8T; A5 Cabriolet, 8F2.0 TFSI CDNB or CDNC examples; the Cabriolet list also includes CAEA and CAEB.Schaeffler lists selected 0AW applications: A5 CDNC June 2008–November 2013, and Cabriolet CAEB / CDNC March 2009–June 2014. Check the engine code and exact build before using a catalogue entry.
Audi A6, C7 / 4G2 / 4G52.0 TFSI CAEB, 155 kW.Schaeffler lists a selected 0AW application for March 2011–May 2013. This is a catalogue period, not a universal model-year range.

Audi identifies Bosch MED17.5 for its CAEB training example; the vehicle listings alone do not establish the exact ECU variant for every other code. Confirm the fitted engine, ECU part number and software, market, drivetrain and emissions system from vehicle-specific service data before choosing a file or a component.

Engine photograph: MIK Motoren’s CAEB replacement-engine listing shows a reconditioned 2.0 TSI / TFSI long block identified by the supplier as EA888 Gen 2. The pictured replacement is an illustration, not evidence of the original ancillaries or exact specification of every vehicle above. The image belongs to its source and is linked rather than reproduced.

Variable valve lift and lubrication

In the CAEB described by SSP 922903, the intake cam has a camshaft adjuster, while Audi Valvelift (AVS) selects different exhaust-cam profiles. Electromagnetic actuators F366–F373 move cam elements; the ECU evaluates a feedback signal associated with a completed movement. Exhaust lift switching is not the same mechanism as intake cam phasing. These details are specific to the cited engine, not evidence of AVS on every Gen 2 engine. Audi SSP 922903, printed pp. 2, 4–12.

The same CAEB document describes a self-regulating oil pump with ECU-controlled oil-pressure regulating valve N428 and oil-pressure switches F22 and F378. The switches report threshold states, not a continuous physical pressure waveform. Check the actual hardware and current diagnostic procedure; compare a calibrated mechanical measurement under the specified conditions when directed by service information. An ECU output command alone does not establish oil pressure. SSP 922903, printed pp. 17–24.

MED17.5 and tuning implications

The CAEB ECU example has electronic throttle, direct injection, a hot-film air-mass sensor and map-controlled ignition with cylinder-selective knock control. Treat airflow, load, requested torque, measured or modelled pressure, ignition corrections and lambda as separate channels. ECU variants and hardware differ within the family; check definitions, units, pressure reference and software identity before using a map name or address. Audi SSP 922903, printed p. 2; Bosch MED17.5.

With a tune or hardware change, first record fuel quality, intake and turbo setup, injector and pump equipment, gearbox, original ECU and TCU versions, diagnostic faults and baseline logs. Compare matching pressure request and actual, fuel rail request and actual, lambda target and an appropriate measured signal, ignition/knock corrections, temperature and operating modes. When AVS or cam signals are available, verify the active mode; requested cam state is not proof of successful physical switching. Preserve protection and diagnose fuel, air and mechanical faults rather than masking them in calibration.

For example map names discussed for a particular MED17.5 wastegate case, see wastegate and boost-control diagnosis. They are forum-reported leads, not proven CAEB-specific symbols. For fuel-system checks and sensor caveats, see fuel pressure and lambda log review; that page's early transverse examples should not be assumed to share every CAEB component.

Oil-consumption diagnosis

Audi's 2013 bulletin 17 13 42 / 2027731 describes an oil-consumption complaint procedure for the listed CAEB vehicles, including a guided measurement and specific equipment/software checks. It is a historical, application-specific service example, not a diagnosis of every engine or an instruction to fit those parts to later cars. Verify the current bulletin and repair information for the vehicle, and check leaks and crankcase ventilation as part of the prescribed diagnosis.

Related: Bosch MED17 family · lambda requests and component protection · MED17.5 torque reporting. Manufacturer training documents are historical descriptions hosted on independent mirrors. Reviewed 17 November 2026.

Family overview: Volkswagen EA888 engine family and ECU identification, including links to the other generations.

Turbo and fuelling upgrades: Transverse and longitudinal applications use different installation hardware. The Gen 1 and Gen 2 turbo kit and conversion guide compares documented packages and supporting parts; the fuel-pump comparison lists selected HPFP and LPFP upgrades.

Injector upgrades: Selected Gen 2 direct-injector options and their different applications are listed in the injector comparison. Confirm engine code, injector part, installation and ECU calibration before selecting a kit.

Charge-air cooling upgrades: The intercooler comparison includes longitudinal B8 and B8.5 kits and selected transverse options. A B8.5 facelift, dynamic steering or Gen 2 TT pipework can change fitment; consult the specific supplier instructions.

Intake upgrades: Transverse and longitudinal Gen 2 installations have different pipework. The intake comparison lists selected kits and their fitment, MAF and secondary-air requirements.

Exhaust upgrades: Routing differs between transverse cars and longitudinal Audi B8 installations. See the exhaust comparison for manufacturer specifications and transmission and bumper restrictions.