Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Carburettors
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 4 to revision 6

Removed text is struck through; added text is highlighted.

The Weber IDF series (36, 40, 44 and 48 IDF) is a vertical downdraft twin-choke individual-runner carburettor sharing the same emulsion-tube and main/air-jet architecture as the sidedraft DCOE, packaged for V-engines, boxer engines (air-cooled VW Type 1 / Type 4, Porsche 356/912) and tight engine bays (Alfa Romeo, Fiat, Ford).

For comparison: a Weber 48 IDA downdraft carburettor, a different model from the IDF described here. Photo: Reforma.imufomot, Wikimedia Commons, public domain.

Adjustment screw diagram

Typical IDF-XE layout: idle mixture, idle speed and air-bypass screws. Original simplified schematic for Tuning Wiki, CC BY 4.0, based on Redline’s IDF-XE control reference; not to scale, and variants or linkages may differ.Typical IDF-XE layout: idle mixture, idle speed and air-bypass screws. Original simplified schematic for Tuning Wiki based on Redline’s IDF-XE control reference; not to scale, and variants or linkages may differ.

View Redline's IDF-XE adjustment-control diagram. The diagram identifies the idle speed screw, separate idle mixture screws, air-bypass screws and locknuts, and accelerator-pump adjustment nut. The drawing is a typical IDF-XE layout; individual versions and linkage arrangements can differ.

1. Models & factory baseline jetting

ModelFactory choke / auxMain jetEmulsion tubeAir correctorIdle jetPump jet / bypass 40 IDF 7028 mm / 4.5115F112005050 / 55 bypass (1.75 needle) 44 IDF 7136 mm / 4.5135F111755050 / 55 bypass (1.75 needle) 48 IDF 640 mm / 4.5150F21805550 / 000 bypass (2.00 needle)

Single centermount vs dual IDF note: CB Performance notes that when a single 40/44/48 IDF is mounted centrally on a plenum manifold (rather than in dual individual-runner pairs), airflow and vacuum distribution change markedly: single centermount setups commonly require larger main and idle jets, 000 pump bypass (closed), an F7 emulsion tube (Aircooled.Net), and a 2 mm hole drilled in each throttle butterfly to stabilise idle airflow.

2. Fuel pressure & float level

Fuel pressure: Redline Weber specifies 2.5–3 psi maximum; higher pressure causes bowl spillage and rich idling. Float height: hold the top cover vertically with the gasket in place and tang resting lightly on the needle ball without compressing the spring. Typical settings are 10 mm closed / 32.5 mm drop on early brass-float 40 IDF and 12 mm closed on 40/44/48 IDF plastic floats (Bigorre float heights). Off-road float drop limit: for rough off-road / Baja use, Redline recommends limiting maximum float drop to 15.5 mm.

3. IDF tuning approach

Bench prep & air-bypass screws: disconnect cross-linkage before tuning. Loosen the 8 mm locknuts on the idle air-bypass screws, seat them lightly shut, and lock the nuts (Redline IDF controls). Speed screw & Lean Best Idle: set idle speed screws ¼–½ turn in after touching the lever (never wind them open past ½ turn, or the butterfly exposes progression holes at idle). Lightly seat each mixture screw and back out 1 full turn; adjust each barrel individually to fastest, smoothest idle. Synchronise & verify idle jet size: match airflow across barrels/carbs by bringing the higher-flowing carb down to the lower-flowing carb. If best idle needs more than 1½ turns out, step up half an idle-jet size; if ½ turn or less, step down half a size (Redline IDF addendum). Main circuit & emulsion tubes: IDF uses the same 73401 (41110.001) main jets, 77401 air correctors, and emulsion tubes as DCOE (most dual 40/44 IDF street builds use F11, moving to F2 or F7 on larger bores/centermounts). Use the pump bypass jet (e.g. 55 vs 000 closed) to adjust how much accelerator-pump fuel returns to the bowl rather than squirting into the throat.

4. Related pages

Weber carburettor tuning overview Weber DCOE and DCO-SP carburettors: specs and tuning Weber IDA and IDA 3C carburettors: specs and tuning Carburettor synchronisation, faults and rebuilds

Sources

Redline Weber 40/44/48 IDF-XE Breakdown & Float Notes, IDF Adjustment Controls, and IDF/DCOE Addendum. CB Performance Weber IDF Jetting Chart and Baseline Weber Jetting Chart. Bigorre Carburateur Float Heights.

Page organisation changed

FieldRevision 4Revision 6
Page typeTechnical articleTechnical article
SubjectCarburettorsCarb Tuning
ParentSection levelSection level
Applies toNo ECU-specific applicabilityNo ECU-specific applicability
Tool groupsNoneNone
Vehicle makesNoneNone

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 4: Weber IDF carburettors: specs and tuning

The Weber IDF series (36, 40, 44 and 48 IDF) is a vertical downdraft twin-choke individual-runner carburettor sharing the same emulsion-tube and main/air-jet architecture as the sidedraft DCOE, packaged for V-engines, boxer engines (air-cooled VW Type 1 / Type 4, Porsche 356/912) and tight engine bays (Alfa Romeo, Fiat, Ford).

Weber 48 IDA downdraft carburettor, shown for comparison with IDF
For comparison: a Weber 48 IDA downdraft carburettor, a different model from the IDF described here. Photo: Reforma.imufomot, Wikimedia Commons, public domain.

Adjustment screw diagram

Schematic of IDF-XE idle controls showing mixture screws, throttle speed screw and air bypass screws
Typical IDF-XE layout: idle mixture, idle speed and air-bypass screws. Original simplified schematic for Tuning Wiki based on Redline’s IDF-XE control reference; not to scale, and variants or linkages may differ.

View Redline's IDF-XE adjustment-control diagram. The diagram identifies the idle speed screw, separate idle mixture screws, air-bypass screws and locknuts, and accelerator-pump adjustment nut. The drawing is a typical IDF-XE layout; individual versions and linkage arrangements can differ.

1. Models & factory baseline jetting

ModelFactory choke / auxMain jetEmulsion tubeAir correctorIdle jetPump jet / bypass
40 IDF 7028 mm / 4.5115F112005050 / 55 bypass (1.75 needle)
44 IDF 7136 mm / 4.5135F111755050 / 55 bypass (1.75 needle)
48 IDF 640 mm / 4.5150F21805550 / 000 bypass (2.00 needle)

Single centermount vs dual IDF note: CB Performance notes that when a single 40/44/48 IDF is mounted centrally on a plenum manifold (rather than in dual individual-runner pairs), airflow and vacuum distribution change markedly: single centermount setups commonly require larger main and idle jets, 000 pump bypass (closed), an F7 emulsion tube (Aircooled.Net), and a 2 mm hole drilled in each throttle butterfly to stabilise idle airflow.

2. Fuel pressure & float level

  • Fuel pressure: Redline Weber specifies 2.5–3 psi maximum; higher pressure causes bowl spillage and rich idling.
  • Float height: hold the top cover vertically with the gasket in place and tang resting lightly on the needle ball without compressing the spring. Typical settings are 10 mm closed / 32.5 mm drop on early brass-float 40 IDF and 12 mm closed on 40/44/48 IDF plastic floats (Bigorre float heights).
  • Off-road float drop limit: for rough off-road / Baja use, Redline recommends limiting maximum float drop to 15.5 mm.

3. IDF tuning approach

  1. Bench prep & air-bypass screws: disconnect cross-linkage before tuning. Loosen the 8 mm locknuts on the idle air-bypass screws, seat them lightly shut, and lock the nuts (Redline IDF controls).
  2. Speed screw & Lean Best Idle: set idle speed screws ¼–½ turn in after touching the lever (never wind them open past ½ turn, or the butterfly exposes progression holes at idle). Lightly seat each mixture screw and back out 1 full turn; adjust each barrel individually to fastest, smoothest idle.
  3. Synchronise & verify idle jet size: match airflow across barrels/carbs by bringing the higher-flowing carb down to the lower-flowing carb. If best idle needs more than 1½ turns out, step up half an idle-jet size; if ½ turn or less, step down half a size (Redline IDF addendum).
  4. Main circuit & emulsion tubes: IDF uses the same 73401 (41110.001) main jets, 77401 air correctors, and emulsion tubes as DCOE (most dual 40/44 IDF street builds use F11, moving to F2 or F7 on larger bores/centermounts). Use the pump bypass jet (e.g. 55 vs 000 closed) to adjust how much accelerator-pump fuel returns to the bowl rather than squirting into the throat.

4. Related pages

Sources

Revision 6: Weber IDF carburettors: specs and tuning

The Weber IDF series (36, 40, 44 and 48 IDF) is a vertical downdraft twin-choke individual-runner carburettor sharing the same emulsion-tube and main/air-jet architecture as the sidedraft DCOE, packaged for V-engines, boxer engines (air-cooled VW Type 1 / Type 4, Porsche 356/912) and tight engine bays (Alfa Romeo, Fiat, Ford).

Weber 48 IDA downdraft carburettor, shown for comparison with IDF
For comparison: a Weber 48 IDA downdraft carburettor, a different model from the IDF described here. Photo: Reforma.imufomot, Wikimedia Commons, public domain.

Adjustment screw diagram

Schematic of IDF-XE idle controls showing mixture screws, throttle speed screw and air bypass screws
Typical IDF-XE layout: idle mixture, idle speed and air-bypass screws. Original simplified schematic for Tuning Wiki, CC BY 4.0, based on Redline’s IDF-XE control reference; not to scale, and variants or linkages may differ.

View Redline's IDF-XE adjustment-control diagram. The diagram identifies the idle speed screw, separate idle mixture screws, air-bypass screws and locknuts, and accelerator-pump adjustment nut. The drawing is a typical IDF-XE layout; individual versions and linkage arrangements can differ.

1. Models & factory baseline jetting

ModelFactory choke / auxMain jetEmulsion tubeAir correctorIdle jetPump jet / bypass
40 IDF 7028 mm / 4.5115F112005050 / 55 bypass (1.75 needle)
44 IDF 7136 mm / 4.5135F111755050 / 55 bypass (1.75 needle)
48 IDF 640 mm / 4.5150F21805550 / 000 bypass (2.00 needle)

Single centermount vs dual IDF note: CB Performance notes that when a single 40/44/48 IDF is mounted centrally on a plenum manifold (rather than in dual individual-runner pairs), airflow and vacuum distribution change markedly: single centermount setups commonly require larger main and idle jets, 000 pump bypass (closed), an F7 emulsion tube (Aircooled.Net), and a 2 mm hole drilled in each throttle butterfly to stabilise idle airflow.

2. Fuel pressure & float level

  • Fuel pressure: Redline Weber specifies 2.5–3 psi maximum; higher pressure causes bowl spillage and rich idling.
  • Float height: hold the top cover vertically with the gasket in place and tang resting lightly on the needle ball without compressing the spring. Typical settings are 10 mm closed / 32.5 mm drop on early brass-float 40 IDF and 12 mm closed on 40/44/48 IDF plastic floats (Bigorre float heights).
  • Off-road float drop limit: for rough off-road / Baja use, Redline recommends limiting maximum float drop to 15.5 mm.

3. IDF tuning approach

  1. Bench prep & air-bypass screws: disconnect cross-linkage before tuning. Loosen the 8 mm locknuts on the idle air-bypass screws, seat them lightly shut, and lock the nuts (Redline IDF controls).
  2. Speed screw & Lean Best Idle: set idle speed screws ¼–½ turn in after touching the lever (never wind them open past ½ turn, or the butterfly exposes progression holes at idle). Lightly seat each mixture screw and back out 1 full turn; adjust each barrel individually to fastest, smoothest idle.
  3. Synchronise & verify idle jet size: match airflow across barrels/carbs by bringing the higher-flowing carb down to the lower-flowing carb. If best idle needs more than 1½ turns out, step up half an idle-jet size; if ½ turn or less, step down half a size (Redline IDF addendum).
  4. Main circuit & emulsion tubes: IDF uses the same 73401 (41110.001) main jets, 77401 air correctors, and emulsion tubes as DCOE (most dual 40/44 IDF street builds use F11, moving to F2 or F7 on larger bores/centermounts). Use the pump bypass jet (e.g. 55 vs 000 closed) to adjust how much accelerator-pump fuel returns to the bowl rather than squirting into the throat.

4. Related pages

Sources