The Weber IDF series (36, 40, 44 and 48 IDF) is a vertical downdraft twin-choke individual-runner carburettor sharing the same emulsion-tube and main/air-jet architecture as the sidedraft DCOE, packaged for V-engines, boxer engines (air-cooled VW Type 1 / Type 4, Porsche 356/912) and tight engine bays (Alfa Romeo, Fiat, Ford).

1. Models & factory baseline jetting
| Model | Factory choke / aux | Main jet | Emulsion tube | Air corrector | Idle jet | Pump jet / bypass |
|---|---|---|---|---|---|---|
| 40 IDF 70 | 28 mm / 4.5 | 115 | F11 | 200 | 50 | 50 / 55 bypass (1.75 needle) |
| 44 IDF 71 | 36 mm / 4.5 | 135 | F11 | 175 | 50 | 50 / 55 bypass (1.75 needle) |
| 48 IDF 6 | 40 mm / 4.5 | 150 | F2 | 180 | 55 | 50 / 000 bypass (2.00 needle) |
Single centermount vs dual IDF note: CB Performance notes that when a single 40/44/48 IDF is mounted centrally on a plenum manifold (rather than in dual individual-runner pairs), airflow and vacuum distribution change markedly: single centermount setups commonly require larger main and idle jets, 000 pump bypass (closed), an F7 emulsion tube (Aircooled.Net), and a 2 mm hole drilled in each throttle butterfly to stabilise idle airflow.
2. Fuel pressure & float level
- Fuel pressure: Redline Weber specifies
2.5–3 psimaximum; higher pressure causes bowl spillage and rich idling. - Float height: hold the top cover vertically with the gasket in place and tang resting lightly on the needle ball without compressing the spring. Typical settings are
10 mmclosed /32.5 mmdrop on early brass-float40 IDFand12 mmclosed on40/44/48 IDFplastic floats (Bigorre float heights). - Off-road float drop limit: for rough off-road / Baja use, Redline recommends limiting maximum float drop to
15.5 mm.
3. IDF tuning approach
- Bench prep & air-bypass screws: disconnect cross-linkage before tuning. Loosen the 8 mm locknuts on the idle air-bypass screws, seat them lightly shut, and lock the nuts (Redline IDF controls).
- Speed screw & Lean Best Idle: set idle speed screws
¼–½ turnin after touching the lever (never wind them open past½ turn, or the butterfly exposes progression holes at idle). Lightly seat each mixture screw and back out1 full turn; adjust each barrel individually to fastest, smoothest idle. - Synchronise & verify idle jet size: match airflow across barrels/carbs by bringing the higher-flowing carb down to the lower-flowing carb. If best idle needs more than
1½ turnsout, step up half an idle-jet size; if½ turnor less, step down half a size (Redline IDF addendum). - Main circuit & emulsion tubes: IDF uses the same
73401(41110.001) main jets,77401air correctors, and emulsion tubes as DCOE (most dual 40/44 IDF street builds useF11, moving toF2orF7on larger bores/centermounts). Use thepump bypassjet (e.g.55vs000closed) to adjust how much accelerator-pump fuel returns to the bowl rather than squirting into the throat.
4. Related pages
- Weber carburettor tuning overview
- Weber DCOE and DCO-SP carburettors: specs and tuning
- Weber IDA and IDA 3C carburettors: specs and tuning
- Carburettor synchronisation, faults and rebuilds