The Weber DGV (manual choke), DGAV (water-heated automatic choke), and DGEV (electric choke)—along with their mirror-image DFV / DFAV / DFEV siblings—are progressive two-barrel downdraft carburettors with fixed venturis. They are widely used both as OEM equipment (Ford Pinto/Crossflow) and as bolt-on replacement conversions for worn OEM carbs on 4-cylinder road and off-road engines.

1. Progressive layout & factory baseline specs
In a progressive 32/36 carburettor, the smaller 32 mm primary barrel (26 mm choke) handles idle, light throttle and road cruising with high air velocity, while the larger 36 mm secondary barrel (27 mm choke) opens mechanically via progressive linkage once primary throttle passes roughly half-way.
| Model (Choke type) | Chokes (P / S) | Aux (P / S) | Main (P / S) | Emulsion (P / S) | Air corr. (P / S) | Idle (P / S) | Pump / needle |
|---|---|---|---|---|---|---|---|
| 32/36 DGV 5A (Manual) | 26 / 27 | 3.5 / 3.5 | 140 / 135 | F50 / F6 | 165 / 160 | 55 / 50 | 50 / 2.00 |
| 32/36 DGAV (Water) / DGEV (Electric) | 26 / 27 | 3.5 / 3.5 | 140 / 140 | F50 / F50 | 170 / 160 | 60 / 50 | 50 / 2.00 |
| 32/36 DFAV (Water) / DFEV (Electric) | 26 / 27 | 3.5 / 3.5 | 137 / 140 | F50 / F66 | 165 / 160 | 60 / 50 | 55 / 2.00 |
| 32 DGV / DGAV / DGEV | 23 / 24 | 3.5 / 4.5 (or 3.5) | 120–125 / 115–130 | F50 / F50 (or F6) | 160–180 / 120–180 | 45–55 / 45–50 | 45–55 / 2.00 |
2. Fuel pressure & float adjustments
- Fuel pressure: Redline Weber recommends 2.5–3 psi; exceeding
3.5 psifrequently pushes fuel past the needle valve and causes rich idling. - Float height (top cover vertical, gasket in place, tang touching ball without compressing spring):
- Brass float (
41030-019): typically35 mmclosed /51 mmdrop (or41 mm / 52 mmdepending on specific body/needle revision—verify the sheet supplied with the rebuild kit). - Plastic / Nitrophyl float (
41030-020): typically17 mmclosed (Bigorre float chart).
- Brass float (
- Off-road float drop: for aggressive off-road / trail bouncing, Redline specifies limiting maximum float drop to
44.5 mm.
3. Tuning approach: progressive Lean Best Idle & Sync Link
- Clear fast-idle cam & set speed screw: confirm the choke fast-idle cam is completely released and the linkage returns freely without binding. On a progressive
DGV/DGAV/DGEV, wind the idle speed screw out from contact, then turn in no more than1½ turnsmaximum past contact (further opening exposes the primary transfer slot at idle and disables mixture-screw control). - Single primary mixture screw: unlike synchronous
38 DGAScarbs, a progressive32/36idles on the primary barrel only via one idle mixture screw (and note the primary74409idle jet on the choke side vs secondary74403idle jet on the inlet side). Lightly seat the mixture screw and back out2 turns(progressive baseline;1 turnon synchronous setups), then tune by ear for smoothest, highest idle before setting final RPM with the speed screw. - Diagnosing primary idle jet size: if best idle requires backing the mixture screw out beyond ~
2½ turns(or opening the speed screw past1½ turns), the primary idle jet is too small; if best idle occurs under1 turnout, the primary idle jet is too large. - Main circuit & secondary transition:
32/36carbs use41120.001(73801) main jets,61440emulsion tubes (F50,F6, etc.), and41360.001(77201) air correctors. A stumble just as the secondary opens often points to the secondary idle jet (74403) being too small or plugged, rather than the primary main jet. - Motorsport Sync Link conversion: for competition classes requiring a single
32/36 DGV/DGAV, Webcon'sSync Linkkit (MT0098L) links both throttle shafts to open synchronously together with a dual-nozzle accelerator pump jet (Webcon Sync Link release).
4. Related pages
- Weber carburettor tuning overview
- Weber DGAS, DGES and DGMS carburettors: specs and tuning
- Weber DCNF, ICT and ICH carburettors: specs and tuning
- Carburettor fuel circuits and metering