Removed text is struck through; added text is highlighted.
Idle is a coordinated target and torque response
Idle control holds engine speed against changing friction, electrical loads, air conditioning and gearbox load. The ECU can select or modify a speed request and coordinate air and ignition torque; a single target table does not describe the whole control system. Start and catalyst-heating phases can request different speeds from normal warm idle.
The following examples are from the community SC8S5031_C_OEM Simos 18.1 ENSC reference. Verify ECU software, engine, transmission, selected branch, A2L, axes, scaling and patch before interpreting a calibration. Square-bracketed array identifiers belong to this definition; do not infer the selected element solely from the name.
Idle speed setpoint maps
ip_n_sp_is_bas[3]: normal idle-speed setpoint, with coolant tco and oil temperature toil axes, output in rpm. ip_n_sp_is_bas_dri[3] provides the reference's LV_DRI drive-position case, with the same input types.
ip_n_sp_is_t_ast: speed setpoint by coolant at start tco_st and time after start t_ast_h. ip_n_sp_is_t_ast_ch is the catalyst-heating variant; ip_n_sp_is_t_ast_stst concerns stop-start. Check which path is active rather than assuming the warm-idle map determines the immediate post-start target.
ip_n_sp_is_ofs_fq: fuel-quality-related idle-speed offset, indexed by a fuel-quality adaptation factor and coolant; it is not itself an ethanol-percentage lookup. c_n_sp_is_bas_lgrd_up and c_n_sp_is_bas_lgrd_down are setpoint change-rate limits, not idle-speed targets.
The broader ENSC setpoint reference also identifies ip_n_sp_is_acin_at, ip_n_sp_is_acin_cvt, ip_n_sp_is_acin_dct and ip_n_sp_is_acin_mt for an air-conditioning-related request, with drive-engaged variants and temperature inputs. ip_n_sp_is_hot_det and its sensor-related variant address hot-detection cases. Transmission and load conditions can alter the selected result; do not copy a value across branches without verifying operation.
Torque reserve and control response
In the ENSC torque-reserve reference, ip_tq_add_is_bol is an idle torque-reserve map in Nm, indexed by predicted speed deviation n_dif_pred and coolant tco. ip_tq_add_is_bol_afu is an alternative-fuel variant, and ip_tq_add_is_driv_mod concerns driving-mode reserve. ip_t_n_dif_ofs_pred is a speed-indexed time constant for predicted speed deviation. These are not idle rpm setpoints; their interaction with the torque model and air-path dynamics matters.
A rough idle can result from a real load, air leak, fuel or ignition problem as well as control calibration. Increasing the speed request or controller response without identifying the cause can mask a fault or introduce oscillation. Preserve stall prevention, diagnostics and protective conditions; no one idle rpm or torque-reserve value suits every engine.
Logging and practical checks
Compare actual rpm with available idle request and operating state during cold and warm operation, neutral/park and drive as applicable, and with A/C or electrical loads changed. The reference lists n_sp_is_bas as a basic setpoint, n_sp_is_ac as an A/C-related request and tq_add_is_bol_2 as a calculated torque-reserve value; these are measurements, not maps or proof of actual delivered torque. idx_trans_typ_at identifies a configured transmission category in that reference, but does not by itself prove which array element is active. See setpoint calculation and torque reserve.
When supported, log coolant/oil temperatures, accelerator, throttle angle, manifold pressure, lambda target and measured lambda, fuel trims and pressure, ignition angle, cam position, misfire counts, torque request and load state. Check intake and PCV leaks, throttle adaptation, fuel delivery, ignition components and mechanical condition before changing idle tables. Compare the same operating conditions before and after a change, including the transition out of catalyst heating.
EVAP interaction: The SC8S5031 ENSC reference identifies n_sp_is_cp_req as a purge-related idle-speed request and lv_n_sp_is_cp_req as its request flag; its description links the request to the filtered canister-load estimate. These are runtime signals, not maps or the final idle target. Where available, log them alongside purge state, actual rpm and lambda when comparing a changing idle target. A request does not prove an EVAP fault; see EVAP purge tuning.
For the return from overrun, see deceleration fuel cut.
Vapour and ventilation guides: EVAP purge · crankcase ventilation.
For automatic restart and idle transitions after an engine stop, see start-stop control and restart.
Related: cold start and warm-up · throttle control · torque model · ignition timing · combustion modes. References reviewed 17 November 2026.
For compressor load estimates and A/C-related transient torque and idle requests, see Simos 18 air conditioning compressor torque and idle.
For alternator-load estimation, after-start response and charging-system checks, see Simos 18 alternator load and idle torque compensation.
Open each version to inspect formatting, tables and photographs.
Revision 7: Simos 18 idle control tuning
Idle is a coordinated target and torque response
Idle control holds engine speed against changing friction, electrical loads, air conditioning and gearbox load. The ECU can select or modify a speed request and coordinate air and ignition torque; a single target table does not describe the whole control system. Start and catalyst-heating phases can request different speeds from normal warm idle.
The following examples are from the community SC8S5031_C_OEM Simos 18.1 ENSC reference. Verify ECU software, engine, transmission, selected branch, A2L, axes, scaling and patch before interpreting a calibration. Square-bracketed array identifiers belong to this definition; do not infer the selected element solely from the name.
Idle speed setpoint maps
ip_n_sp_is_bas[3]: normal idle-speed setpoint, with coolant tco and oil temperature toil axes, output in rpm. ip_n_sp_is_bas_dri[3] provides the reference's LV_DRI drive-position case, with the same input types.
ip_n_sp_is_t_ast: speed setpoint by coolant at start tco_st and time after start t_ast_h. ip_n_sp_is_t_ast_ch is the catalyst-heating variant; ip_n_sp_is_t_ast_stst concerns stop-start. Check which path is active rather than assuming the warm-idle map determines the immediate post-start target.
ip_n_sp_is_ofs_fq: fuel-quality-related idle-speed offset, indexed by a fuel-quality adaptation factor and coolant; it is not itself an ethanol-percentage lookup. c_n_sp_is_bas_lgrd_up and c_n_sp_is_bas_lgrd_down are setpoint change-rate limits, not idle-speed targets.
The broader ENSC setpoint reference also identifies ip_n_sp_is_acin_at, ip_n_sp_is_acin_cvt, ip_n_sp_is_acin_dct and ip_n_sp_is_acin_mt for an air-conditioning-related request, with drive-engaged variants and temperature inputs. ip_n_sp_is_hot_det and its sensor-related variant address hot-detection cases. Transmission and load conditions can alter the selected result; do not copy a value across branches without verifying operation.
Torque reserve and control response
In the ENSC torque-reserve reference, ip_tq_add_is_bol is an idle torque-reserve map in Nm, indexed by predicted speed deviation n_dif_pred and coolant tco. ip_tq_add_is_bol_afu is an alternative-fuel variant, and ip_tq_add_is_driv_mod concerns driving-mode reserve. ip_t_n_dif_ofs_pred is a speed-indexed time constant for predicted speed deviation. These are not idle rpm setpoints; their interaction with the torque model and air-path dynamics matters.
A rough idle can result from a real load, air leak, fuel or ignition problem as well as control calibration. Increasing the speed request or controller response without identifying the cause can mask a fault or introduce oscillation. Preserve stall prevention, diagnostics and protective conditions; no one idle rpm or torque-reserve value suits every engine.
Logging and practical checks
Compare actual rpm with available idle request and operating state during cold and warm operation, neutral/park and drive as applicable, and with A/C or electrical loads changed. The reference lists n_sp_is_bas as a basic setpoint, n_sp_is_ac as an A/C-related request and tq_add_is_bol_2 as a calculated torque-reserve value; these are measurements, not maps or proof of actual delivered torque. idx_trans_typ_at identifies a configured transmission category in that reference, but does not by itself prove which array element is active. See setpoint calculation and torque reserve.
When supported, log coolant/oil temperatures, accelerator, throttle angle, manifold pressure, lambda target and measured lambda, fuel trims and pressure, ignition angle, cam position, misfire counts, torque request and load state. Check intake and PCV leaks, throttle adaptation, fuel delivery, ignition components and mechanical condition before changing idle tables. Compare the same operating conditions before and after a change, including the transition out of catalyst heating.
EVAP interaction: The SC8S5031 ENSC reference identifies n_sp_is_cp_req as a purge-related idle-speed request and lv_n_sp_is_cp_req as its request flag; its description links the request to the filtered canister-load estimate. These are runtime signals, not maps or the final idle target. Where available, log them alongside purge state, actual rpm and lambda when comparing a changing idle target. A request does not prove an EVAP fault; see EVAP purge tuning.
For the return from overrun, see deceleration fuel cut.
Vapour and ventilation guides: EVAP purge · crankcase ventilation.
For automatic restart and idle transitions after an engine stop, see start-stop control and restart.
Related: cold start and warm-up · throttle control · torque model · ignition timing · combustion modes. References reviewed 17 November 2026.
For compressor load estimates and A/C-related transient torque and idle requests, see Simos 18 air conditioning compressor torque and idle.
For alternator-load estimation, after-start response and charging-system checks, see Simos 18 alternator load and idle torque compensation.
Revision 7: Simos 18 idle control tuning
Idle is a coordinated target and torque response
Idle control holds engine speed against changing friction, electrical loads, air conditioning and gearbox load. The ECU can select or modify a speed request and coordinate air and ignition torque; a single target table does not describe the whole control system. Start and catalyst-heating phases can request different speeds from normal warm idle.
The following examples are from the community SC8S5031_C_OEM Simos 18.1 ENSC reference. Verify ECU software, engine, transmission, selected branch, A2L, axes, scaling and patch before interpreting a calibration. Square-bracketed array identifiers belong to this definition; do not infer the selected element solely from the name.
Idle speed setpoint maps
ip_n_sp_is_bas[3]: normal idle-speed setpoint, with coolant tco and oil temperature toil axes, output in rpm. ip_n_sp_is_bas_dri[3] provides the reference's LV_DRI drive-position case, with the same input types.
ip_n_sp_is_t_ast: speed setpoint by coolant at start tco_st and time after start t_ast_h. ip_n_sp_is_t_ast_ch is the catalyst-heating variant; ip_n_sp_is_t_ast_stst concerns stop-start. Check which path is active rather than assuming the warm-idle map determines the immediate post-start target.
ip_n_sp_is_ofs_fq: fuel-quality-related idle-speed offset, indexed by a fuel-quality adaptation factor and coolant; it is not itself an ethanol-percentage lookup. c_n_sp_is_bas_lgrd_up and c_n_sp_is_bas_lgrd_down are setpoint change-rate limits, not idle-speed targets.
The broader ENSC setpoint reference also identifies ip_n_sp_is_acin_at, ip_n_sp_is_acin_cvt, ip_n_sp_is_acin_dct and ip_n_sp_is_acin_mt for an air-conditioning-related request, with drive-engaged variants and temperature inputs. ip_n_sp_is_hot_det and its sensor-related variant address hot-detection cases. Transmission and load conditions can alter the selected result; do not copy a value across branches without verifying operation.
Torque reserve and control response
In the ENSC torque-reserve reference, ip_tq_add_is_bol is an idle torque-reserve map in Nm, indexed by predicted speed deviation n_dif_pred and coolant tco. ip_tq_add_is_bol_afu is an alternative-fuel variant, and ip_tq_add_is_driv_mod concerns driving-mode reserve. ip_t_n_dif_ofs_pred is a speed-indexed time constant for predicted speed deviation. These are not idle rpm setpoints; their interaction with the torque model and air-path dynamics matters.
A rough idle can result from a real load, air leak, fuel or ignition problem as well as control calibration. Increasing the speed request or controller response without identifying the cause can mask a fault or introduce oscillation. Preserve stall prevention, diagnostics and protective conditions; no one idle rpm or torque-reserve value suits every engine.
Logging and practical checks
Compare actual rpm with available idle request and operating state during cold and warm operation, neutral/park and drive as applicable, and with A/C or electrical loads changed. The reference lists n_sp_is_bas as a basic setpoint, n_sp_is_ac as an A/C-related request and tq_add_is_bol_2 as a calculated torque-reserve value; these are measurements, not maps or proof of actual delivered torque. idx_trans_typ_at identifies a configured transmission category in that reference, but does not by itself prove which array element is active. See setpoint calculation and torque reserve.
When supported, log coolant/oil temperatures, accelerator, throttle angle, manifold pressure, lambda target and measured lambda, fuel trims and pressure, ignition angle, cam position, misfire counts, torque request and load state. Check intake and PCV leaks, throttle adaptation, fuel delivery, ignition components and mechanical condition before changing idle tables. Compare the same operating conditions before and after a change, including the transition out of catalyst heating.
EVAP interaction: The SC8S5031 ENSC reference identifies n_sp_is_cp_req as a purge-related idle-speed request and lv_n_sp_is_cp_req as its request flag; its description links the request to the filtered canister-load estimate. These are runtime signals, not maps or the final idle target. Where available, log them alongside purge state, actual rpm and lambda when comparing a changing idle target. A request does not prove an EVAP fault; see EVAP purge tuning.
For the return from overrun, see deceleration fuel cut.
Vapour and ventilation guides: EVAP purge · crankcase ventilation.
For automatic restart and idle transitions after an engine stop, see start-stop control and restart.
Related: cold start and warm-up · throttle control · torque model · ignition timing · combustion modes. References reviewed 17 November 2026.
For compressor load estimates and A/C-related transient torque and idle requests, see Simos 18 air conditioning compressor torque and idle.
For alternator-load estimation, after-start response and charging-system checks, see Simos 18 alternator load and idle torque compensation.