Scope: This page concerns automatic engine stop/restart, not the ignition pushbutton itself. The control names are examples from the community SC8S5031_C_OEM Simos 18.1 reference; hardware, software, vehicle coordination and calibration differ by application. Match the exact ECU definition, state-machine behavior, units and indices before interpreting a field. The examples are not a universal disable recipe.
How stop and restart are coordinated
Automatic stop/start depends on conditions across the vehicle, not only an engine-speed threshold. In Volkswagen Tech Tip 27-19-02TT, which covers its listed 2018–2019 Atlas and Tiguan and 2019 Jetta and Arteon vehicles rather than all Simos 18 applications, the stop conditions include a closed driver's door and bonnet, seat belt, sufficient battery charge and suitable temperatures and climate demand. Low battery voltage, steering input or vehicle movement are among the listed reasons an automatic restart may be needed. An open door or bonnet can require a manual restart under that document's conditions. Confirm the vehicle-specific operating instructions.
An interrupted stop is a separate transition sometimes called change of mind: the control system can receive a restart demand while the engine is still stopping. Starter assistance, injection and ignition may therefore depend on engine state. It is not equivalent to a conventional cold start. The ENSS start-stop reference and IGSP starting-ignition reference describe examples of this distinction.
Example system and transition calibration names
The following fields are from the image-specific SysOpmDrv and ENSS references. The extracted descriptions do not establish the meaning of individual configuration bits or their behavior in another ECU:
DATA_SysOpmDrv.SysOpmDrv_stAcvBas_C_VWis a bit-coded base start/stop configuration.DATA_SysOpmDrv.SysOpmDrv_stStopPhd_C_VWandDATA_SysOpmDrv.SysOpmDrv_stStrtPhd_C_VWare described as stop- and start-prohibition masks, respectively. Their bit allocations and consequences are not confirmed here; do not infer an off value.DATA_SysOpmDrv.SysOpmDrv_tiDlyHldStopReq_C_VWdescribes a vehicle-standstill-recognition delay before a stop request;DATA_SysOpmDrv.SysOpmDrv_tiDlyStopEnaBas_C_VWis a delay to enable a base stop. Both are in seconds in this definition and are not ignition timing maps.c_t_dly_stst_st_reqis a start-request delay in milliseconds.c_t_ast_min_ena_stall_stis a minimum engine-run time to enable an automatic stall restart. Check operating conditions: an automatic stop/restart and a stall recovery are distinct events.c_n_max_stst_stop_intrand relatedc_n_min_stst_stop_intrfields are described as speed thresholds associated with stop interruption;lc_stst_stop_intr_enaconfigures an associated recovery strategy. These are transition controls, not evidence of a safe permanent setting.lv_stst_st_req_prepindicates preparation for a start request,lv_dly_inj_act_stst_stop_intrindicates an injection delay during a change-of-mind condition, andlv_stall_st_reqis an automatic stall-start request. These are runtime signals, not calibration maps, and may not be exposed by a particular logger.
Restart ignition examples
The SC8S5031 start ignition reference distinguishes restart paths. ip_iga_st_stst_h_prs[3] and ip_iga_st_stst_h_prs_dt[3] are described as high-pressure stop/start basic ignition maps for starts without and with an engaged gear, respectively. Their displayed axes are engine speed and coolant temperature; outputs are crank-angle degrees. Verify array selection and the applicable meaning of high-pressure start in the target software.
ip_iga_st_stst_cor is a stop/start ignition correction against manifold intake-air temperature and ambient pressure. ip_iga_stst_intr is an interruption-recovery ignition map against engine speed and cylinder air mass. These are starting or recovery calibrations; they are not ordinary full-load advance targets. Further selection, corrections and safety controls affect the final ignition angle.
Aftermarket features and checks
An MHH Auto post lists an inverted start/stop button among claimed Simos customisations, without supplying a verified implementation or calibration. Treat it as a community claim. The Simos.app Main Patch guide separately offers map selection via the start/stop button and states that the OEM start/stop function is not suppressed; an optional patch setting can take over the button lamp. This is specific to that patch and its settings. Button behavior, lamp indication, remembered map selection and actual stop/start state are separate things.
- Record engine and ECU software, transmission, installed patches, selected mode, start/stop button state, dashboard message and the conditions when the symptom occurs. Check applicable owner and workshop information.
- If the feature is unavailable, inspect stored faults and battery/charging condition, relevant door, bonnet, belt and climate states, temperatures and gear or brake status before assuming calibration damage. VW's Tech Tip distinguishes an informational standby message from a malfunction when operation is otherwise normal.
- Compare stop request, start request, transition state, engine speed, starter command and voltage when suitable supported channels are available. Availability, signal definitions and sampling rates vary. A button light alone does not prove the engine's actual state.
- Validate both a normal stop/restart and any reproducible interrupted-stop or restart complaint under appropriate workshop procedures. Preserve the vehicle's safety interlocks, automatic restart and fault handling; do not infer individual configuration bits from a similar software version.
Related: cold start tuning · idle control tuning · switchable maps · tuning and log diagnosis.
Sources
- VW Tech Tip 27-19-02TT, transaction 2055075/1 — vehicle-specific start/stop operating and diagnostic example.
- SC8S5031 SysOpmDrv, ENSS start-stop, and IGSP start ignition — community, image-specific ECU cross-references.
- Simos.app Main Patch documentation — its own button behavior and optional lamp control.
- MHH Auto Simos customisation discussion — unverified feature claim.