Removed text is struck through; added text is highlighted.
The Weber DCOE (Doppio Corpo Orizzontale, double-body horizontal) and racing DCO/SP series are synchronous twin-choke sidedraft carburettors. Almost always installed so each throttle barrel feeds one individual cylinder runner, they combine interchangeable main venturis, auxiliary venturis, emulsion wells, idle progression jets and mechanical accelerator pumps in a compact alloy casting.
Weber 40 DCOE sidedraft carburettor mounted on an Abarth 1000 Bialbero twin-cam. Photo: Mr.choppers, resized; Wikimedia Commons, CC BY-SA 3.0.Weber 40 DCOE sidedraft carburettor mounted on an Abarth 1000 Bialbero twin-cam. Photo: Mr.choppers, Wikimedia Commons, CC BY-SA 3.0.
Weber 45 DCOE 9 sidedraft body showing trumpets and top jet-cover access. Photo: Reforma.imufomot, Wikimedia Commons, Public domain.
Adjustment screw diagramWeber 45 DCOE 9: the two spring-loaded idle mixture screws, shown from above. The idle-speed linkage is outside this view. Original simplified redraw for Tuning Wiki, CC BY 4.0, from the public-domain photograph by Reforma.imufomot; control identification cross-checked against Redline’s DCOE diagram. Check the exact model; not to scale.View Redline's DCOE adjustment-control diagram. The labelled view identifies the idle speed screw, the two idle mixture screws and the air-bypass screws and locknuts. Scroll to “DCOE Adjustment controls”. This is a typical DCOE layout; confirm the precise variant and linkage before applying it to a DCO/SP.50 DCO/SP and 1/SP: Carburetion.com exploded drawing and parts key identifies the throttle-stop screw as item 36, mixture screws as 41, and air-bypass screws as 64. Confirm the exact carburettor number before applying the drawing to another DCO/SP size or version.
1. Choke (venturi) & barrel sizing
Power potential and low-RPM tractability are governed primarily by the removable main venturi (choke), not the outer barrel diameter (Dave Andrews Weber DCOE guide). Ideal throttle-barrel size is approximately venturi size × 1.25 (for example, a 36 mm choke pairs ideally with a 45 DCOE, though a 40 DCOE can also fit a 36 mm choke).
Fuel pressure: keep regulated delivery pressure around 2.5–3 psi; excessive pump pressure forces fuel past the needle valve and floods the auxiliary venturis.
Dry float height (lid vertical, gasket fitted, tang touching ball without compressing spring):
40 / 45 DCOE brass float: typically 8–9 mm closed / 14–15 mm drop (5–8 mm on some early 45 DCOE models; verify exact float weight and casting type).
40 / 45 DCOE / DCO-SP plastic float: typically 12.5 mm closed / 25 mm drop (12 mm on 48/50/55 DCO/SP plastic float, Bigorre float chart; Pierce Manifolds).
Wet fuel-level check: with the emulsion tube removed, an acrylic optical depth gauge in the emulsion well typically reads 25 mm ± 1 mm below the top deck (Weber DCOE reference).
3. Idle, progression & the 2,500–3,000 rpm stumble
Close air-bypass screws first: on late emissions-type DCOE 151/152 bodies with air-bleed bypass screws under 8 mm locknuts, lightly seat them closed before base idle setup.
Idle speed stop & Lean Best Idle: keep the idle speed stop no more than ¼–½ turn past contact (so the throttle butterfly does not uncover progression holes at idle). Start mixture screws at 1 turn out (2.5 turns on coarse-thread early DCOEs). Tune each barrel individually for smoothest, fastest idle.
Synchronise carbs: match airflow with a Synchrometer or Uni-Syn by bringing the higher-flowing carb down to the lower-flowing carb, then adjust both evenly to target idle (900–1,100 rpm on cammed engines).
Fix 2,500–3,000 rpm stumble with the F-bleed: Webcon UK notes that the DCOE idle jet's numeric prefix (e.g. 50 = 0.50 mm) sets idle fuel flow so the mixture screw sits around 1–3 turns out, whereas the F-number sets the side air-bleed hole controlling upper progression just before the main circuit cuts in. Keep the fuel number fixed and step between F8 (1.2 mm, leanest), F9 (1.0 mm, standard start) and F6 (0.7 mm, richest) to cure a lean misfire or rich stumble around 2,500–3,000 rpm.
4. Main jet, emulsion tube & air corrector tuning
Starting formulas: main jet ≈ venturi (mm) × 4; air corrector ≈ main jet + 50.
Emulsion tubes by cylinder size: 250–325 cc → F11; 275–400 cc → F15; 350–475 cc → F9 or F16; 450–575 cc → F2.
Splitting roles: tune the main jet (Weber 41110.001) for full-load mid-to-upper RPM AFR, then use the air corrector (77401 / 41360 series) to flatten the top-end slope (larger leans high RPM, smaller enriches high RPM).
5. Related pages
Weber carburettor tuning overview
Weber IDF carburettors: specs and tuning
Weber IDA and IDA 3C carburettors: specs and tuning
Carburettor synchronisation, faults and rebuilds
Sources
Weber Carburettors Type 38–48 DCOE Manual.
D. V. Andrews: Selection and Tuning of Weber DCOE Carburettors.
Webcon UK: Fixing 2500–3000 rpm DCOE Stumble/Misfire and Baseline Weber Jetting Chart.
Bigorre Carburateur Float Heights and Pierce Manifolds Float Level Sheet.
Page organisation changed
Field
Revision 2
Revision 8
Page type
Technical article
Technical article
Subject
Carburettors
Carb Tuning
Parent
Section level
Section level
Applies to
No ECU-specific applicability
No ECU-specific applicability
Tool groups
None
None
Vehicle makes
None
None
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: Weber DCOE and DCO-SP carburettors: specs and tuning
The Weber DCOE (Doppio Corpo Orizzontale, double-body horizontal) and racing DCO/SP series are synchronous twin-choke sidedraft carburettors. Almost always installed so each throttle barrel feeds one individual cylinder runner, they combine interchangeable main venturis, auxiliary venturis, emulsion wells, idle progression jets and mechanical accelerator pumps in a compact alloy casting.
Weber 40 DCOE sidedraft carburettor mounted on an Abarth 1000 Bialbero twin-cam. Photo: Mr.choppers, Wikimedia Commons, CC BY-SA 3.0.Weber 45 DCOE 9 sidedraft body showing trumpets and top jet-cover access. Photo: Reforma.imufomot, Wikimedia Commons, Public domain.
1. Choke (venturi) & barrel sizing
Power potential and low-RPM tractability are governed primarily by the removable main venturi (choke), not the outer barrel diameter (Dave Andrews Weber DCOE guide). Ideal throttle-barrel size is approximately venturi size × 1.25 (for example, a 36 mm choke pairs ideally with a 45 DCOE, though a 40 DCOE can also fit a 36 mm choke).
Model
Available chokes
Factory baseline example (choke / main / em. tube / air / idle / pump / needle)
Fuel pressure: keep regulated delivery pressure around 2.5–3 psi; excessive pump pressure forces fuel past the needle valve and floods the auxiliary venturis.
40 / 45 DCOE brass float: typically 8–9 mm closed / 14–15 mm drop (5–8 mm on some early 45 DCOE models; verify exact float weight and casting type).
40 / 45 DCOE / DCO-SP plastic float: typically 12.5 mm closed / 25 mm drop (12 mm on 48/50/55 DCO/SP plastic float, Bigorre float chart; Pierce Manifolds).
Wet fuel-level check: with the emulsion tube removed, an acrylic optical depth gauge in the emulsion well typically reads 25 mm ± 1 mm below the top deck (Weber DCOE reference).
3. Idle, progression & the 2,500–3,000 rpm stumble
Close air-bypass screws first: on late emissions-type DCOE 151/152 bodies with air-bleed bypass screws under 8 mm locknuts, lightly seat them closed before base idle setup.
Idle speed stop & Lean Best Idle: keep the idle speed stop no more than ¼–½ turn past contact (so the throttle butterfly does not uncover progression holes at idle). Start mixture screws at 1 turn out (2.5 turns on coarse-thread early DCOEs). Tune each barrel individually for smoothest, fastest idle.
Synchronise carbs: match airflow with a Synchrometer or Uni-Syn by bringing the higher-flowing carb down to the lower-flowing carb, then adjust both evenly to target idle (900–1,100 rpm on cammed engines).
Fix 2,500–3,000 rpm stumble with the F-bleed:Webcon UK notes that the DCOE idle jet's numeric prefix (e.g. 50 = 0.50 mm) sets idle fuel flow so the mixture screw sits around 1–3 turns out, whereas the F-number sets the side air-bleed hole controlling upper progression just before the main circuit cuts in. Keep the fuel number fixed and step between F8 (1.2 mm, leanest), F9 (1.0 mm, standard start) and F6 (0.7 mm, richest) to cure a lean misfire or rich stumble around 2,500–3,000 rpm.
4. Main jet, emulsion tube & air corrector tuning
Starting formulas:main jet ≈ venturi (mm) × 4; air corrector ≈ main jet + 50.
Emulsion tubes by cylinder size:250–325 cc → F11; 275–400 cc → F15; 350–475 cc → F9 or F16; 450–575 cc → F2.
Splitting roles: tune the main jet (Weber 41110.001) for full-load mid-to-upper RPM AFR, then use the air corrector (77401 / 41360 series) to flatten the top-end slope (larger leans high RPM, smaller enriches high RPM).
Revision 8: Weber DCOE and DCO-SP carburettors: specs and tuning
The Weber DCOE (Doppio Corpo Orizzontale, double-body horizontal) and racing DCO/SP series are synchronous twin-choke sidedraft carburettors. Almost always installed so each throttle barrel feeds one individual cylinder runner, they combine interchangeable main venturis, auxiliary venturis, emulsion wells, idle progression jets and mechanical accelerator pumps in a compact alloy casting.
Weber 40 DCOE sidedraft carburettor mounted on an Abarth 1000 Bialbero twin-cam. Photo: Mr.choppers, resized; Wikimedia Commons, CC BY-SA 3.0.Weber 45 DCOE 9 sidedraft body showing trumpets and top jet-cover access. Photo: Reforma.imufomot, Wikimedia Commons, Public domain.
Adjustment screw diagram
Weber 45 DCOE 9: the two spring-loaded idle mixture screws, shown from above. The idle-speed linkage is outside this view. Original simplified redraw for Tuning Wiki, CC BY 4.0, from the public-domain photograph by Reforma.imufomot; control identification cross-checked against Redline’s DCOE diagram. Check the exact model; not to scale.
View Redline's DCOE adjustment-control diagram. The labelled view identifies the idle speed screw, the two idle mixture screws and the air-bypass screws and locknuts. Scroll to “DCOE Adjustment controls”. This is a typical DCOE layout; confirm the precise variant and linkage before applying it to a DCO/SP.
50 DCO/SP and 1/SP:Carburetion.com exploded drawing and parts key identifies the throttle-stop screw as item 36, mixture screws as 41, and air-bypass screws as 64. Confirm the exact carburettor number before applying the drawing to another DCO/SP size or version.
1. Choke (venturi) & barrel sizing
Power potential and low-RPM tractability are governed primarily by the removable main venturi (choke), not the outer barrel diameter (Dave Andrews Weber DCOE guide). Ideal throttle-barrel size is approximately venturi size × 1.25 (for example, a 36 mm choke pairs ideally with a 45 DCOE, though a 40 DCOE can also fit a 36 mm choke).
Model
Available chokes
Factory baseline example (choke / main / em. tube / air / idle / pump / needle)
Fuel pressure: keep regulated delivery pressure around 2.5–3 psi; excessive pump pressure forces fuel past the needle valve and floods the auxiliary venturis.
40 / 45 DCOE brass float: typically 8–9 mm closed / 14–15 mm drop (5–8 mm on some early 45 DCOE models; verify exact float weight and casting type).
40 / 45 DCOE / DCO-SP plastic float: typically 12.5 mm closed / 25 mm drop (12 mm on 48/50/55 DCO/SP plastic float, Bigorre float chart; Pierce Manifolds).
Wet fuel-level check: with the emulsion tube removed, an acrylic optical depth gauge in the emulsion well typically reads 25 mm ± 1 mm below the top deck (Weber DCOE reference).
3. Idle, progression & the 2,500–3,000 rpm stumble
Close air-bypass screws first: on late emissions-type DCOE 151/152 bodies with air-bleed bypass screws under 8 mm locknuts, lightly seat them closed before base idle setup.
Idle speed stop & Lean Best Idle: keep the idle speed stop no more than ¼–½ turn past contact (so the throttle butterfly does not uncover progression holes at idle). Start mixture screws at 1 turn out (2.5 turns on coarse-thread early DCOEs). Tune each barrel individually for smoothest, fastest idle.
Synchronise carbs: match airflow with a Synchrometer or Uni-Syn by bringing the higher-flowing carb down to the lower-flowing carb, then adjust both evenly to target idle (900–1,100 rpm on cammed engines).
Fix 2,500–3,000 rpm stumble with the F-bleed:Webcon UK notes that the DCOE idle jet's numeric prefix (e.g. 50 = 0.50 mm) sets idle fuel flow so the mixture screw sits around 1–3 turns out, whereas the F-number sets the side air-bleed hole controlling upper progression just before the main circuit cuts in. Keep the fuel number fixed and step between F8 (1.2 mm, leanest), F9 (1.0 mm, standard start) and F6 (0.7 mm, richest) to cure a lean misfire or rich stumble around 2,500–3,000 rpm.
4. Main jet, emulsion tube & air corrector tuning
Starting formulas:main jet ≈ venturi (mm) × 4; air corrector ≈ main jet + 50.
Emulsion tubes by cylinder size:250–325 cc → F11; 275–400 cc → F15; 350–475 cc → F9 or F16; 450–575 cc → F2.
Splitting roles: tune the main jet (Weber 41110.001) for full-load mid-to-upper RPM AFR, then use the air corrector (77401 / 41360 series) to flatten the top-end slope (larger leans high RPM, smaller enriches high RPM).