Mechanical ventilation and ECU modelling
Crankcase ventilation manages blow-by and separates oil before gases return to the intake. It is distinct from fuel-tank EVAP purge, although some applications connect the charcoal-filter path at the oil-separator assembly. Audi SSP 920243, printed pages 23–27, describes a Gen3 EA888 arrangement with a fine separator, pressure regulator and self-actuating check valves. In its example the intake-manifold path is used in suction operation and the turbo-compressor inlet path in boost. These are hardware-specific examples, not proof that every Simos 18 vehicle has the same hose routing or PCV assembly.
Volkswagen SSP 820533 describes related coarse and fine separation and oil return on its EA888 Gen3 applications. Check the engine code, market, separator revision, actual hose/check-valve layout and applicable repair information. The ECU-controlled N80 is the canister purge valve; a mechanical PCV pressure-regulating diaphragm is not automatically an ECU-controlled actuator.
Crankcase model maps: SC8S5031 example
The following are modelling research leads from SC8S5031_C_OEM INSY crankcase ventilation. They do not prove that every field is active in the file or that the car has a crankcase pressure sensor. Match ASW, CAL, sensor/actuator fitment, branch selectors, units, and active model before interpreting the definition.
ip_flow_crcv_blowby_airandip_flow_crcv_blowby_rgdescribe estimated fresh-air and residual-gas blow-by components. The referenced axes are pressure-labelled in hPa and speed-labelled in rpm, but both haveNO_INPUT_QUANTITYmetadata. The description says mass flow while the field lists l/s: resolve the inconsistency against the actual A2L and implementation before using the axes or units.ip_fac_cor_blowby_air_tcoandip_fac_cor_blowby_rg_tcoare coolant-temperature-related blow-by corrections. Their axis metadata also lacks a direct input name; do not assume a particular runtime signal without checking.ip_kp_prs_im_crcvis an rpm-indexed gain for matching measured and modelled intake-manifold pressure in this model. It is not a desired crankcase pressure or an idle fuel target. The reference warns excessive gain can destabilise the intake-manifold model.ip_prs_hc_vap_crcvconcerns fuel-vapour pressure with a temperature-labelled axis. The reference calls its vapour-model discussion preliminary and identifies the axis input asNO_INPUT_QUANTITY; confirm implementation before drawing conclusions.
The same INSY reference identifies ip_fac_cor_blowby_air_eff_iga and ip_fac_cor_blowby_rg_eff_iga as ignition-efficiency-related correction factors for the fresh-air and residual-gas blow-by estimates. The shared axis is labelled for ignition efficiency but its input is NO_INPUT_QUANTITY; establish the actual runtime input before using it. These factors affect the model, not the mechanical regulator setpoint or a direct blow-by measurement.
prs_crcv_oil_cpt is a calculated model-path pressure after the oil separator, distinct from prs_crcv inside the crankcase. Both are listed as runtime measurements in the reference; the measurement data type alone does not establish either is physically sensed. Compare like locations and pressure references when using an independent gauge.
The generic reference also contains ip_fac_pwm_slv_crcv, described as a solenoid-opening correction. Its presence is not evidence that a particular EA888 Gen3 vehicle has an electrically actuated PCV valve, nor that the map is used. Establish physical fitment and configured function first.
Regulator model and transient behaviour
The SC8S5031 INSY cross-reference also lists c_prs_ctl_dif_sp_crcv, a modelled pressure-setpoint difference from ambient in hPa; its narrative subtracts this value from ambient pressure. c_prs_loss_oil_cpt_crcv represents a modelled separator pressure loss in hPa. These are scalar calibration parameters, not direct pressure measurements or proof of an electronically commanded PCV valve. Confirm absolute versus differential pressure, active software branch and actual hardware; changing a model parameter does not physically alter the mechanical regulator or repair a restriction.
ip_t1_vlv_crcv is a temperature-related regulator-model low-pass time constant in seconds. Its temperature-labelled axis has NO_INPUT_QUANTITY metadata, and the description discusses a combination of coolant and intake temperatures: verify the actual lookup and branch. c_fac_prs_vlv_gain_crcv is the associated model gain; the reference warns that excessive gain can make model flow oscillate. ip_crlc_ratio_air_m_gas_im is described as a correlation factor for air-mass correction after start, with a seconds-labelled axis but no directly identified axis input. Neither is a generic fix for a hardware leak, tip-out surge or idle fault. INSY model reference.
The CEVC cross-reference lists ip_t_es_toil_evap_crcv_st[1] and ip_t_es_toil_fall_crcv_st[1] as engine-stop fuel-evaporation correction maps with gram outputs and minute- and temperature-labelled axes. The input fields are NO_INPUT_QUANTITY, so confirm the actual lookup signals, the meaning of each output and indexing against the matched implementation. ip_fac_mff_cor_evap_lq is a liquid-fuel-flow correction factor with a temperature-labelled axis, likewise without a declared input. These calculations help explain why warm restart and soak duration deserve controlled comparison; they do not measure fuel contamination in oil.
Oil vapour and fuel correction
The separate CEVC crankcase fuel-evaporation reference lists ip_fac_evap_crcv_mass as an evaporation correction against modelled fuel-in-oil mass mass_fuel_int_oil in grams. It is a model factor, not a valve duty setting or a laboratory measurement of oil dilution. The LACO oil-dilution reference contains detection and lambda-control interactions; neither a trim correction nor a modelled value alone diagnoses oil condition.
In the INSY reference, prs_crcv, mfl_air_crcv and related gas-flow variables are model-path runtime values. Their presence as measurements in a definition does not establish that a vehicle has a physical crankcase-pressure or flow sensor. Distinguish ECU estimates from a correctly installed physical gauge or other manufacturer-approved test.
Additional oil-vapour model terms
The SC8S5031 CEVC fuel-evaporation cross-reference also labels ip_fac_vol_crcv a crankcase-ventilation-flow factor. Its two axis units are g and hPa, but their input metadata is NO_INPUT_QUANTITY; verify both physical meanings and sign conventions against the matched implementation. ip_flow_vol_add_prs_pcv is described as an additional-flow term for the effect of fuel evaporation in oil, with mass_fuel_int_oil in g as its axis and an l/s output. This is a model correction, not a measured leak rate, a regulator setting or a standard catch-can calibration.
flow_vol_pcv and flow_vol_pcv_dly are runtime values listed in the model, whereas lamb_delta_fuel_vap_pred[0] in the CEVC oil-dilution reference is the predicted lambda influence of crankcase fuel evaporation. Logger exposure and whether these paths are active vary; their names alone establish neither a fitted flow sensor nor actual fuel dilution. Investigate actual hardware and oil condition independently.
Hardware changes and diagnosis
An intake, turbo-inlet, separator or catch-can change can alter the available pressure source, flow restriction, oil separation or check-valve behaviour. Compare the actual plumbing in vacuum and boost, ensure the correct orientation and function of check valves, and verify oil returns and connections using the applicable current service procedure. Do not infer that one aftermarket layout works across all EA888 revisions. Retain appropriate emissions equipment and fault monitoring.
Record idle quality, fuel trims, lambda, manifold and upstream pressures, temperatures, oil consumption and relevant faults, and compare against the documented hardware and test conditions. A crankcase pressure measurement and a manifold-vacuum measurement are different; do not copy a regulator design differential or intake-vacuum specification as a universal crankcase limit. Whistling, oil leaks, smoke or a trim shift can have several causes.
VW technical tip 01-18-14TT describes lean trims and excessive crankcase vacuum in particular 2013–2018 US-market vehicles and engine codes after other causes have been checked. Its example includes an intake-vacuum check and possible cylinder-head sealing plugs; it is not proof that every lean condition is a PCV failure or a universal crankcase specification.
Workshop example
In a 2015 Stage 1 GTI owner discussion, the owner reported rough idle, then found the oil filler cap sitting crooked and reported normal idle after reseating it. The thread includes several other possible diagnoses. ECU software and an independently measured leak were not reported, so this is an anecdotal check for cap seating, not proof that every rough idle is a PCV or cap fault.
On the engine illustrated by Audi SSP 920243 (printed pages 23–24), separated oil returns through a shutoff valve in the sump honeycomb insert. Audi describes the valve closing when cornering oil movement exposes the return. This is a reason to check the complete oil-return and separator arrangement when changing breather hardware; it does not prove the cause of any particular track failure.
In a separate MQB inlet-pipe investigation, an owner describes comparing multiple turbo inlets, stock and tuned boost, and measured PCV and crankcase vacuum. The author reports that inlet design affected the tested PCV system. Test conditions, separator revision and plumbing matter: turbo-inlet pressure and crankcase pressure are separate locations, and the result is not a universal specification or proof for every aftermarket inlet.
Track-use reports and retrofit evidence
One Mk7 GTI track owner reported a catch can filling with nearly a litre of oil after several hard laps, low engine oil level, EPC and P164B. The suggested cause involving crankcase pressure and oil pickup was the owner's hypothesis; measurements and the outcome of a later retrofit were not established in the post. Treat an oil-pressure warning as a reason to stop and investigate, not as evidence that the ECU model needs changing.
In a separate Data Driven MQB report, the author observed smoke and ignition knock retard correlated with hard right-hand turns, then reported an autocross without the earlier knock symptom after an experimental Mk8 separator retrofit. At that article's publication, track testing of the initial configuration remained pending. These are uncontrolled, hardware-specific observations, not proof of a universal cause or retrofit fitment. Check oil level and pressure, separator routing and oil return, engine condition, logging and part compatibility for the actual vehicle.
Related: EVAP purge · fuel trim · lambda control · idle control · bigger turbo tuning. References reviewed 17 November 2026.
For pre-turbo restriction, airflow tests and air-cleaner model examples, see Simos 18 intake and turbo inlet upgrades.
For the modelled fuel-in-oil path, lambda interaction and oil-analysis evidence, see Simos 18 oil dilution and fuel contamination.