Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Simos 18
Applies to
Simos 18.1
Tool groups
None
Manufacturers
Volkswagen Group

Applicability: The engineering identifiers below are from the community SC8S5031_C_OEM Simos 18.1 cross-reference unless another source is named. Identify the engine, hardware, ECU software, calibration and installed patches; match the A2L, axes, units, signs, indices and selectors. Extracted descriptions sometimes conflict. Values, addresses and states from another software version are not a calibration for this vehicle. SC8S5031 reference.

Phasing, lift and angle conventions

Continuous cam phasing changes the relationship of a camshaft to the crankshaft; switchable valve lift selects a different cam profile. These are separate controls, though lift, flap, cam position and combustion mode can affect which torque and ignition model entries are used. Volkswagen's SSP 522 describes both on its CHHA/CHHB 2.0 TSI examples; it does not establish the hardware fitted to every Simos 18 vehicle. For lift switching, see valve lift tuning.

Before comparing a map with a log, establish whether the angle is measured relative to crank top dead centre, the cam's passive reference position or another adjusted reference; confirm crank versus cam degrees and sign. A single displayed phaser value does not by itself establish valve overlap. The VVTI customer adaptation reference includes multiple reference conventions.

Cam setpoint maps

  • ip_cam_sp_vcp[1][1][0] is a port-flap- and valve-lift-dependent cam position setpoint in the published VVTI setpoint reference. This instance uses engine speed and torque-derived air-mass setpoint maf_stk_sp_tqi_vcp in mg/stroke as axes, and produces a crank-angle setpoint. The second axis is a requested model value, not necessarily measured airflow. The community XDF labels this instance intake/standard lift; verify every index and selector in the target software.
  • ip_cam_sp_scav_vcp[1] is an example dynamic driver-request/scavenging cam setpoint against speed and torque-related air-mass setpoint. ip_cam_sp_spt_vcp[1][1][0] is a sport-switch-dependent example; its displayed instance has very small dimensions, so presence alone does not prove a useful alternate map on another ECU.
  • ip_cam_sp_is_vcp[1] is an idle-speed cam setpoint example. ip_cam_sp_pl_ch_vcp[1][0] and ip_cam_sp_is_mplh_ch_vcp[1][0] relate to part-load and MPI idle catalyst-heating conditions respectively. These are separate operating paths; some extracted captions on the source page are mismatched, so confirm the function and actual activation in the matching definition.

Limits and controller signals

ip_cam_sp_toil_lim_max_vcp[1] is an example maximum cam setpoint versus oil temperature. ip_cam_sp_temp_lim_max_vcp[1] is a hot-condition setpoint limit, and ip_cam_sp_lim_act_vcp[1][0] and ip_cam_sp_lim_pas_vcp[1][0] are movement-gradient limit examples. They are not ordinary phase targets; compare conditions and final requests before attributing a slow response to the primary target map. VVTI setpoint and limits.

In the same source, cam_sp_hom_afs_tar_vcp[1] is an unlimited target and cam_sp_hom_afs_vcp[1] the final setpoint for the documented calculation, which includes temperature and gradient effects. These are runtime measurements, not editable maps. In the IVVT controller reference, cam_mdl_vcp[1] is modelled position and cam_sp_dif_vcp[1] is a setpoint difference against a no-delay actuator model, not necessarily an actual measured error. Controller PWM, position-validity and state signals are also diagnostic context, not proof of a particular mechanical fault.

Dynamic and steady position diagnosis

The SC8S5031 dynamic-position diagnosis describes ip_t_min_diag_dyn_act_vcp[1] and ip_t_min_diag_dyn_pas_vcp[1] as active- and passive-direction evaluation times in seconds against engine speed and oil temperature. cam_dif_diag_dyn_vcp[1] records cam-position change during the diagnostic event, while lv_diag_dyn_act_vcp[1] indicates that the dynamic diagnosis is active. These are not normal cam-position setpoints; absence of a fault when the monitor has not run does not establish healthy movement.

The distinct steady-setpoint diagnosis lists id_cam_hys_de_diag_vcp[1][1] as deviation hysteresis in crank degrees versus oil temperature and id_cam_dif_int_max_diag_vcp[1][1] as an integrator limit in crank degrees-seconds versus oil temperature. cam_dif_int_diag_vcp[1][1] is a runtime integrated deviation, not an editable angle target. Monitor activation, array indexing, filtered values and logger support must be checked on the target. Preserve the diagnostics and investigate oil, control and mechanical faults; these names do not supply a universal acceptable phase error.

Tuning and log review

EcuTek's EA888 guide describes evaluating intake and exhaust phasing at matched engine-speed/load points on its development application. Check torque response alongside air charge, boost, lambda, individual-cylinder knock and temperature, then check transitions and lower-load operation. Cam changes can alter the selected/interpolated torque and ignition model regions, so validate them together; a target angle alone is not evidence of a performance improvement.

EcuTek lists Intake Cam Absolute Position, Intake Cam Absolute Position Setpoint, Exhaust Cam Absolute Position and Exhaust Cam Absolute Position Setpoint for its supported applications. Compare request and actual with rpm, load, oil temperature, lift and flap state, controller status and faults. Check logging units, reference and sample timing; investigate oil supply, actuator and mechanical timing when an actual position repeatedly fails to follow an achievable request. The EA888 cam timing discussion is an exploratory community lead, not a verified universal angle recipe.

For crank and cam sensor events, synchronization and correlation-fault diagnosis, see Simos 18 crankshaft and camshaft synchronization.

Related: camshaft timing · valve lift tuning · torque model · ignition timing · bigger turbos · log diagnosis.

For phaser movement-control maps, holding PWM and deviation-learning diagnostics, see Simos 18 cam phaser control and holding PWM adaptation.