Tuning Wiki
Applies to

Check the hardware and software limits stated in this article.

Commanded phasing and hydraulic response

Cam timing tables specify desired position; moving and holding that position is a separate control and mechanical task. The ECU commands the cam oil-control valve and evaluates camshaft-position feedback, but a duty command does not establish oil flow or actual phaser movement. On the EA888 engines listed in VW technical tip 10-18-01TT, the adjuster relies on engine oil pressure and a locking mechanism during start-up. Engine hardware and phaser arrangements vary: use current repair information for the actual engine code.

The fields below are examples from the community SC8S5031_C_OEM VVTI controller and related cross-references, not universal Simos 18 settings. Confirm ECU ASW/CAL, cam index and function configuration, source, axis units, signal reference and available logging. An array ending [1] does not on its own identify intake or exhaust on another software version. Some extracted captions or axis names conflict and are flagged below.

Movement model and control maps

  • ip_fac_ctl_act_vcp[1] and ip_fac_ctl_pas_vcp[1] weight proportional control in the documented active and passive directions. The displayed axes are engine speed n_32 in rpm and oil temperature toil in °C. These are movement-control factors, not the requested cam timing tables.
  • ip_vel_ivs_act_vcp[1] and ip_vel_ivs_pas_vcp[1] describe inverse actuator adjustment speed against the same physical quantities, with output in milliseconds per crank degree. They are model calibrations, not directly measured phaser velocity or proof of oil pressure. Verify active/passive polarity for the installed phaser before making inferences.
  • ip_t_ctl_act_vcp[1] and ip_t_ctl_pas_vcp[1] are labelled proportional-control adjustment energization times in milliseconds. Their cam-angle-related first axes are marked online_dummy; the active entry's copied prose describes a different reference-position time. Resolve the lookup and caption against the matching software before using the values. VVTI controller reference.

cam_mdl_vcp[1] is a modelled position; cam_mdl_dif_vcp[1] is described as actual versus modelled position, while cam_sp_dif_vcp[1] uses a no-delay model in the existing timing guide. These are different from actual-versus-requested phaser error. state_ctl_vcp[1], lv_vcp_psn_vld[1] and pwm_vcp[1] are runtime control state, position-validity and adjustment PWM examples. State encodings and availability are target-specific; a valid edge alone does not prove that the chain or phaser is mechanically correct.

Holding PWM and learned correction

The holding-PWM reference lists ip_fac_vb_pwm_vcp as an adjustment-PWM factor versus battery voltage vb, and ip_fac_tmag_pwm_vcp as a solenoid-temperature-related correction versus tmag_vcp. ip_frq_pwm_hld_vcp and ip_frq_pwm_vcp are separate holding and adjustment PWM frequency maps in Hz versus battery voltage and solenoid temperature in this reference. Temperature inputs can be calculated; do not infer a dedicated physical solenoid-temperature sensor from their names.

The deviation-adaptation reference lists pwm_hld_ad_vcp[1] as an adaptive holding-PWM table against tmag_vcp, and pwm_hld_de_ad_vcp[1][1] as the current learned deviation correction. Distinguish stored adaptive entries from a base map, actual valve position, and the cam reference-position adaptation used for correlation. A table value or ECU PWM does not show whether the spool valve or hydraulic circuit is healthy.

  • ip_cyc_min_de_ad_vcp gives the number of adaptation cycles for controller fading before this learning begins, against engine speed and oil temperature; the source describes a cycle in relation to used cam edges. ip_cycnr_max_de_ad_vcp limits adaptation cycles against oil temperature. Cycle counts are not seconds.
  • ip_cycnr_ramp_de_ad_vcp[1] describes cycles between learning steps; ip_pwm_vcp_chg_de_ad describes the PWM change per adaptation step, with oil temperature as its second axis. The cam-difference-labelled first axes in these entries identify online_dummy rather than a confirmed live input, and copied prose for the latter describes the former. Confirm the implementation and signal before tuning.
  • lv_vcp_de_ad_req[1][1] and lv_vcp_de_ad_end[1][1] are request and end-state flags; a request is not completion or proof of a successful repair. The source states that reaching the maximum cycle count can terminate adaptation without saving. Monitor conditions and fault states matter.

Fault investigation and tuning verification

Log intake and exhaust actual and requested position where supported, rpm, engine load, oil and coolant temperature, battery voltage, control state, timing fault codes and freeze frame. Ensure the same angle reference, crank-versus-cam degrees and correct sampling before comparing positions. A physically measured oil-pressure test uses the manufacturer's procedure and equipment; a temperature or duty signal is not an oil-pressure measurement.

VW's 10-18-01TT technical tip covers cold-start rattle and timing faults for its listed 2010–2018 US models and specific 1.8/2.0 engine codes. It calls for checking the timing drive and then specified/actual cam values; the diagnostic test conditions and values apply only to that document's listed engines. A rattle or a P0011 code alone does not establish a failed phaser. Follow current vehicle-specific service instructions and investigate oil supply, valve wiring, mechanical timing and phaser movement before changing calibration or clearing learned values.

In an IS38-tuned Mk7 GTI owner report, intermittent limp mode and rough running followed prior engine rebuilding; the owner supplied P000A and P0011 intake faults and freeze-frame readings. They considered electrical, mechanical and calibration causes, but the post does not establish a confirmed fault or repair. It is a reason to preserve freeze-frame and test the relevant paths, not a universal parts or map prescription.

Related: camshaft timing · crank and cam synchronisation · oil pressure control · valve lift tuning · log diagnosis. References reviewed 17 November 2026.

Continue the conversation

If this topic interests you, consider joining the following forums. They host material referenced in this article.