Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Simos 18
Applies to
Simos 18.1
Tool groups
None
Manufacturers
Volkswagen Group

Mechanical ventilation and ECU modelling

Crankcase ventilation manages blow-by and separates oil before gases return to the intake. It is distinct from fuel-tank EVAP purge, although some applications connect the charcoal-filter path at the oil-separator assembly. Audi SSP 920243, printed pages 23–27, describes a Gen3 EA888 arrangement with a fine separator, pressure regulator and self-actuating check valves. In its example the intake-manifold path is used in suction operation and the turbo-compressor inlet path in boost. These are hardware-specific examples, not proof that every Simos 18 vehicle has the same hose routing or PCV assembly.

Volkswagen SSP 820533 describes related coarse and fine separation and oil return on its EA888 Gen3 applications. Check the engine code, market, separator revision, actual hose/check-valve layout and applicable repair information. The ECU-controlled N80 is the canister purge valve; a mechanical PCV pressure-regulating diaphragm is not automatically an ECU-controlled actuator.

Crankcase model maps: SC8S5031 example

The following are modelling research leads from SC8S5031_C_OEM INSY crankcase ventilation. They do not prove that every field is active in the file or that the car has a crankcase pressure sensor. Match ASW, CAL, sensor/actuator fitment, branch selectors, units, and active model before interpreting the definition.

  • ip_flow_crcv_blowby_air and ip_flow_crcv_blowby_rg describe estimated fresh-air and residual-gas blow-by components. The referenced axes are pressure-labelled in hPa and speed-labelled in rpm, but both have NO_INPUT_QUANTITY metadata. The description says mass flow while the field lists l/s: resolve the inconsistency against the actual A2L and implementation before using the axes or units.
  • ip_fac_cor_blowby_air_tco and ip_fac_cor_blowby_rg_tco are coolant-temperature-related blow-by corrections. Their axis metadata also lacks a direct input name; do not assume a particular runtime signal without checking.
  • ip_kp_prs_im_crcv is an rpm-indexed gain for matching measured and modelled intake-manifold pressure in this model. It is not a desired crankcase pressure or an idle fuel target. The reference warns excessive gain can destabilise the intake-manifold model.
  • ip_prs_hc_vap_crcv concerns fuel-vapour pressure with a temperature-labelled axis. The reference calls its vapour-model discussion preliminary and identifies the axis input as NO_INPUT_QUANTITY; confirm implementation before drawing conclusions.

The same INSY reference identifies ip_fac_cor_blowby_air_eff_iga and ip_fac_cor_blowby_rg_eff_iga as ignition-efficiency-related correction factors for the fresh-air and residual-gas blow-by estimates. The shared axis is labelled for ignition efficiency but its input is NO_INPUT_QUANTITY; establish the actual runtime input before using it. These factors affect the model, not the mechanical regulator setpoint or a direct blow-by measurement.

prs_crcv_oil_cpt is a calculated model-path pressure after the oil separator, distinct from prs_crcv inside the crankcase. Both are listed as runtime measurements in the reference; the measurement data type alone does not establish either is physically sensed. Compare like locations and pressure references when using an independent gauge.

The generic reference also contains ip_fac_pwm_slv_crcv, described as a solenoid-opening correction. Its presence is not evidence that a particular EA888 Gen3 vehicle has an electrically actuated PCV valve, nor that the map is used. Establish physical fitment and configured function first.

Oil vapour and fuel correction

The separate CEVC crankcase fuel-evaporation reference lists ip_fac_evap_crcv_mass as an evaporation correction against modelled fuel-in-oil mass mass_fuel_int_oil in grams. It is a model factor, not a valve duty setting or a laboratory measurement of oil dilution. The LACO oil-dilution reference contains detection and lambda-control interactions; neither a trim correction nor a modelled value alone diagnoses oil condition.

In the INSY reference, prs_crcv, mfl_air_crcv and related gas-flow variables are model-path runtime values. Their presence as measurements in a definition does not establish that a vehicle has a physical crankcase-pressure or flow sensor. Distinguish ECU estimates from a correctly installed physical gauge or other manufacturer-approved test.

Additional oil-vapour model terms

The SC8S5031 CEVC fuel-evaporation cross-reference also labels ip_fac_vol_crcv a crankcase-ventilation-flow factor. Its two axis units are g and hPa, but their input metadata is NO_INPUT_QUANTITY; verify both physical meanings and sign conventions against the matched implementation. ip_flow_vol_add_prs_pcv is described as an additional-flow term for the effect of fuel evaporation in oil, with mass_fuel_int_oil in g as its axis and an l/s output. This is a model correction, not a measured leak rate, a regulator setting or a standard catch-can calibration.

flow_vol_pcv and flow_vol_pcv_dly are runtime values listed in the model, whereas lamb_delta_fuel_vap_pred[0] in the CEVC oil-dilution reference is the predicted lambda influence of crankcase fuel evaporation. Logger exposure and whether these paths are active vary; their names alone establish neither a fitted flow sensor nor actual fuel dilution. Investigate actual hardware and oil condition independently.

Hardware changes and diagnosis

An intake, turbo-inlet, separator or catch-can change can alter the available pressure source, flow restriction, oil separation or check-valve behaviour. Compare the actual plumbing in vacuum and boost, ensure the correct orientation and function of check valves, and verify oil returns and connections using the applicable current service procedure. Do not infer that one aftermarket layout works across all EA888 revisions. Retain appropriate emissions equipment and fault monitoring.

Record idle quality, fuel trims, lambda, manifold and upstream pressures, temperatures, oil consumption and relevant faults, and compare against the documented hardware and test conditions. A crankcase pressure measurement and a manifold-vacuum measurement are different; do not copy a regulator design differential or intake-vacuum specification as a universal crankcase limit. Whistling, oil leaks, smoke or a trim shift can have several causes.

VW technical tip 01-18-14TT describes lean trims and excessive crankcase vacuum in particular 2013–2018 US-market vehicles and engine codes after other causes have been checked. Its example includes an intake-vacuum check and possible cylinder-head sealing plugs; it is not proof that every lean condition is a PCV failure or a universal crankcase specification.

Workshop example

In a 2015 Stage 1 GTI owner discussion, the owner reported rough idle, then found the oil filler cap sitting crooked and reported normal idle after reseating it. The thread includes several other possible diagnoses. ECU software and an independently measured leak were not reported, so this is an anecdotal check for cap seating, not proof that every rough idle is a PCV or cap fault.

Related: EVAP purge · fuel trim · lambda control · idle control · bigger turbo tuning. References reviewed 17 November 2026.

For pre-turbo restriction, airflow tests and air-cleaner model examples, see Simos 18 intake and turbo inlet upgrades.