Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Simos 18
Applies to
Simos 18.1
Tool groups
None
Manufacturers
Volkswagen Group

Scope. Spark-plug and coil selection are hardware decisions for the specific EA888 engine and tune; Simos 18 software does not itself identify the correct part or gap. Exact engine, plug and coil part numbers, load, fuel, duty cycle and tuner requirements matter. The calibration examples below are from the community SC8S5031_C_OEM Simos 18.1 reference, not universal settings.

Plug gap, heat range and fitment

Incorrect gap or damaged electrodes can contribute to misfire; the useful gap depends on the plug, cylinder conditions and ignition system. NGK's gap guidance says to check the gap against the applicable specification and avoid levering against a fine centre electrode or insulator. Some plug designs are not intended for ordinary gap adjustment: follow the plug manufacturer's method. Greater cylinder pressure can increase ignition demand; reducing the gap is not a substitute for diagnosing low voltage, damaged coils, fuel delivery or mechanical faults.

Heat range describes the plug's ability to transfer heat from its firing end, not a direct instruction to cool the engine. NGK notes that modified engines with greater thermal demand may require a colder plug; its general technical guide also notes that an excessively cold plug can foul under low-temperature or light-load conditions. Heat-range number systems are manufacturer-specific. Match thread, reach, seat, projection, electrode design, material and plug/coil compatibility to the actual cylinder head and application.

One tuner's EA888.3 example

EQT's 2022 EA888.3 article describes a 2017 GTI stock-plug example and its own recommendations: one step colder with a 0.024-inch (about 0.61 mm) gap for its IS20/IS38 applications, and two steps colder at that gap for its stated larger-turbo applications. Those are EQT's examples for its documented applications, not an OEM specification or a universal recommendation. Check the current recommendations for the exact tune and plug, and verify vehicle fitment.

EQT also reports plug ground-electrode failures in its community and says the cause of individual failures is uncertain, including possible part, handling and operating factors. Its observations do not establish a failure rate or prove any one design caused every failure. If an electrode is visibly missing or damaged, stop running the engine and have the engine and missing material professionally assessed; don't continue load testing as a way to diagnose it.

Coil dwell is separate from spark timing

Dwell is the period commanded to charge a coil before ignition; ignition angle is the timing of the firing event. Neither an ECU dwell request nor an ignition angle guarantees actual current, spark energy or combustion. The SC8S5031 IGRE reference lists ip_td and ip_td_h as dwell-related maps and ip_td_vb_cor as a voltage-related dwell correction. Axis captions and extracted descriptions can conflict: verify the active mode, units, axes, driver and coil. Do not increase dwell merely because a plug misfires; excessive dwell can overheat a coil. See ignition coil dwell control for source details and limits.

Misfire diagnosis under load or at idle

Record the cylinder, engine speed, load, fuel, temperatures, gear, boost, lambda target and actual, rail-pressure target and actual, ignition timing, knock correction and misfire status where supported. A misfire count, knock correction and lean lambda indication are different observations. ECU-reported battery voltage and supply at a coil are different measurement points. Check whether misfire detection is active during any custom launch, cut or other intervention.

Volkswagen's misfire diagnostic bulletin 01-16-13 / 2033805 covers its listed gasoline models and describes using guided diagnostics, controlled component swaps and matching the original operating conditions. If the fault follows a component, that is useful evidence; if it stays with a cylinder, investigate other causes including injector, wiring and mechanical condition under the applicable repair procedure. P0300 alone does not identify the faulty part. High-pressure fuel-system work requires the correct service procedure.

In a 2017 hybrid-IS38 GTI owner discussion, the owner reported warm-idle cylinder-4 misfires after a plug change, with no observed misfire under boost; another plug and a coil swap did not change the reported symptom. The exact ECU software, diagnostic data and cause were not independently established. This is a useful reminder to compare idle and load conditions; it does not prove the new plug design was faulty or that the reported cure for another car will apply.

Related: misfire detection and diagnosis · coil dwell control · knock detection and control · bigger turbo tuning · direct injector characterisation. References reviewed 17 November 2026.