Applicability. This guide describes ignition-coil charge time and examples from the community SC8S5031_C_OEM Simos 18.1 cross-reference. Match the ECU hardware and software, coil, driver, definition, units and active combustion mode before using any name below. The source has conflicting extracted descriptions: axis metadata and functional context are leads for verification, not a substitute for testing the target. No addresses or universal dwell values are supplied.
What dwell controls
Dwell is the period used to charge an inductive ignition coil before the firing event. It is distinct from spark advance: spark advance specifies when the ignition event is commanded relative to crank position, whereas dwell concerns coil charging beforehand. Supply voltage, coil characteristics, driver behavior, temperature and available time matter. Too little dwell can impair ignition; excessive dwell can overheat or damage ignition hardware. Obtain the particular coil manufacturer's data and verify compatibility and wiring. Haltech dwell-time guidance; this general guidance is not a Simos-specific coil specification.
The ECU command, the current through the coil and the actual spark are different observations. If testing with a scope, use the correct procedure and appropriately rated equipment for the vehicle and ignition system; high ignition voltage is hazardous. Pico's primary-current explanation is a general distributor-system example and should not be copied as a wiring procedure for an integrated coil-on-plug module.
Example SC8S5031 dwell maps
The IGRE dwell-time reference lists:
ip_tdandip_td_h— dwell-related maps with millisecond output and axesmaf_hb(air mass in mg/stroke) andn_32(rpm). The latter is described for high-energy mode. An inherited narrative elsewhere mentions battery voltage and speed forip_td, conflicting with these axes; do not call it a voltage-by-rpm table without checking the actual implementation.ip_td_vb_cor— dwell-time correction related to battery voltage, output in milliseconds. The referenced axes are dwell time in ms and voltage in V; their runtime inputs are markedNO_INPUT_QUANTITYin the extraction. Confirm the input selection and whether the result is a corrected value or an additive correction before editing.ip_fac_td_n_grd— a factor whose axis metadata is engine speed and engine-speed gradient in rpm/s. The field label describes air mass instead, so validate the function in the matching software before attributing its effect.c_td_tol— described as maximum dwell time;c_td_open_bolis a minimum open time. Neither defines a safe value for a replacement coil by itself.
Combustion-mode selection is separate: lc_idx_ign_cmb_mod[38] maps combustion modes to ignition modes in this reference, while lv_egy_ign_h_mod is a runtime high-energy-mode flag. Do not infer all index meanings from another software build.
Limits and observable signals
The IGRE spark and dwell output reference lists ip_td_fac_min and ip_td_fac_max as minimum and maximum dwell factors against rpm, with separate starting factors c_td_fac_st_min and c_td_fac_st_max. In the dwell switch reference, c_vb_td_max_lim_l and c_vb_td_max_lim_h are voltage thresholds in maximum-dwell logic, and td_lim_max is a calculated runtime maximum. Confirm actual priority, limits and hysteresis in the target file.
The switch reference labels td_igc[3] the cylinder-specific nominal dwell request, td_igc_act[3] dwell currently applied by the ECU I/O software, and td_igc_mes[3] applied dwell for the selected cylinder. These are ECU-reported variables, not direct measurements of coil current or proof of spark energy or combustion. Check channel availability, selected cylinder and indexing on the target logger and software.
The same reference labels td_fac_min_tmp[3] and td_fac_max_tmp[3] cylinder-specific minimum and maximum dwell factors. Its extracted narrative describes td_fac_min_tmp * td_igc as a minimum during advance changes or strong acceleration, and td_fac_max_tmp * td_igc as a maximum during retard changes or strong deceleration. These limits can affect the available dwell interval as timing changes; compare the request, factors and ECU-reported applied timing before attributing a transient issue to the base dwell maps. The extraction is fragmented, so verify its logic in the matching file.
The dwell-period reference also labels c_map_drv_td_max a load-dynamics threshold for maximum dwell (hPa/ms) and c_t_td_max_map_dyn the associated time (s). These labels alone do not establish the comparison direction or activation logic. The switch reference also conflicts on whether the low-voltage threshold c_vb_td_max_lim_l applies above or below its value; resolve that in the target implementation before making changes.
Diagnosis and hardware changes
- Record the engine and ECU identifiers, installed coils and plugs, wiring, battery condition, software and the operating conditions of any misfire. Compare fault and freeze-frame data, lambda, fuel pressure, ignition timing and cylinder-specific misfire or knock data as available. The misfire guide explains why a misfire is not automatically a coil problem.
- Check supply and grounds under relevant electrical load using the manufacturer's method. ECU-reported voltage and the voltage at the coil are different measurement locations and need not be identical.
- For replacement coils, establish the supported drive method, connector and electrical specifications and acquire coil-specific dwell versus voltage and thermal information. Do not copy a value from a different coil or assume more dwell always yields more useful spark.
- Where appropriate, a trained technician can compare current and ignition waveforms with equipment and procedures suited to the installed coil and its integrated electronics. Confirm actual behavior over relevant conditions and respect component thermal limits; avoid assuming the ignition trigger exposes primary voltage.
Related: ignition timing · knock detection · misfire detection and diagnosis · tuning and log diagnosis.
For tuned EA888 plug selection and ignition-hardware diagnosis, see Simos 18 spark plugs, coils and tuned-engine misfire diagnosis.
Sources
- Community SC8S5031 IGRE dwell period definitions; image-specific, extracted descriptions may conflict.
- IGRE dwell and combustion-mode switches and spark and dwell output definitions.
- Haltech: Dwell Time, general coil-dependent guidance; Pico: primary voltage and current, general ignition principles.