Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Simos 18
Applies to
Simos 18.1
Tool groups
None
Manufacturers
Volkswagen Group

Scope. Many EA888 applications use an electric turbo wastegate actuator with position feedback; other turbochargers or custom control systems use different hardware. This guide covers actuator travel learning and diagnosis, not the separate adaptive correction of boost-control feedforward. Match the vehicle, turbo and actuator part numbers, ECU ASW/CAL, tools and current service procedure before applying an example.

Mechanical stops and control adaptation

On an electric system, the ECU commands actuator motion and interprets position feedback over its travel. A first adaptation or basic setting establishes actuator endpoints under the conditions required by the diagnostic tool. This differs from the ip_ad_fac_bpa_sp adaptive boost-control correction described in wastegate and boost control; a completed travel learn does not prove that boost follows its target, and a boost-control adaptation reset does not repair a sticking linkage.

APR's IS38 installation note describes a first adaptation of the charge-pressure actuator and identifies an excessively tight or loose setting as a possible reason for failure. That procedure applies to its stated installation. Other turbochargers, actuators, software and diagnostic tools can have different specifications or conditions: do not transfer an online rod-turn count or voltage as a universal target. Record the original position, faults and measurements and use the correct manufacturer's procedure.

SC8S5031 field names

The following are research examples from the community SC8S5031_C_OEM actuator adaptation and diagnosis reference. They are not a promise of support or active use on every Simos 18 file. Check matching definitions, array index, scaling, units, state conditions and logger availability.

  • lv_bpa_ad_asa_suc[0] is a runtime indicator described as successful tester-requested adaptation. lv_bpa_ad_req[0] indicates an adaptation request in the actuator operating-manager reference. A request is not the same as a successful completion.
  • vp_bpa_ad_tol[0] is an adapted upper mechanical-stop voltage; vp_bpa_ad_bol_max[0] is described as a lifetime maximum for the lower-stop adaptation stored in non-volatile memory. These are runtime or stored values in volts, not maps or universal acceptable voltage limits. Stop naming and physical open/closed direction require verification for the installed actuator.
  • vp_bpa_ad_fil[0] is filtered sensor voltage for adaptation; vp_bpa_ad_dif[0] is a temperature-related adaptation voltage correction. The sensor reference labels posn_bpa_raw[0] a raw position value in percent, not raw voltage. Compare position request and feedback with consistent polarity and scaling.
  • ip_vp_bpa_ad_dif[0] is an exhaust-temperature-related voltage-correction curve. Its temperature axis metadata says NO_INPUT_QUANTITY; identify the actual runtime input in the matched implementation. ip_crlc_vp_bpa_ad_dif is a filtering coefficient against catalyst mass-flow mfl_sum_cat in kg/h. Neither is an adjustment for an incorrectly assembled linkage.
  • c_t_vp_bpa_ad_acq is an actuator sensor-limit acquisition timer; c_vb_bpa_pas_ad_min is a minimum battery-voltage threshold for passive adaptation. c_vp_bpa_ad_rel and c_vp_bpa_ad_rel_first describe different adaptation-change limits. These are calibration fields in the example, not guidance to relax diagnostics or force a failed basic setting to pass.

Faults and workshop evidence

Volkswagen technical bulletin 21-25-01 / 2077251 addresses a sticking wastegate adjustment on listed vehicles, including 2015–2021 GTI 2.0T and 2015–2019 Golf R 2.0T, with P00AF or P2563 stored. For P2563, the bulletin specifically requires symptom code 14846. It directs a check of linkage movement; if movement is easy, that bulletin is not the applicable repair. Its procedure uses ODIS basic settings following the relevant mechanical work. Confirm the vehicle, fault details, tool conditions and current repair information before applying it.

A Mk7/Mk7.5 GTI owner's P00AF discussion reports restricted movement when cold and improvement after treating the linkage; the owner later reported continued use with periodic maintenance. This is an individual account with no independently verified diagnosis or precise ECU software. Other causes include the actuator, sensor, wiring and turbo mechanics, so an identical code is not proof of the same fault. Follow the applicable manufacturer procedure rather than copying a forum lubricant or forcing a hot mechanism.

Diagnostic sequence

  1. Record full fault codes and subcodes, freeze-frame, temperature, battery voltage, ECU ID, turbo and actuator parts and recent hardware changes. Check whether a required basic setting completed or was aborted and retain the result.
  2. Check the linkage and valve travel, mounting, electrical supply, wiring and connector with the correct service procedure. Actuator travel and feedback may be affected by heat, binding, damage or incorrect adjustment.
  3. Where supported, compare specified and actual actuator position and sensor voltage during an appropriate controlled test, including stop-learning status. Check the channel's source, units and position direction. A plausible single voltage does not prove movement across the range.
  4. Only after mechanical and electrical issues are resolved, perform the specified adaptation under the tool's required conditions. Then compare requested and actual pressure and actuator position, including relevant torque intervention and boost-protection states. A successful test is not a substitute for checking operation under load.

Related: wastegate and boost control · bigger turbo tuning · MAP and boost pressure sensors · turbocharger protection. References reviewed 17 November 2026.