Removed text is struck through; added text is highlighted.
The Weber IDF series (36, 40, 44 and 48 IDF) is a vertical downdraft twin-choke individual-runner carburettor sharing the same emulsion-tube and main/air-jet architecture as the sidedraft DCOE, packaged for V-engines, boxer engines (air-cooled VW Type 1 / Type 4, Porsche 356/912) and tight engine bays (Alfa Romeo, Fiat, Ford).
For comparison: a Weber 48 IDA downdraft carburettor, a different model from the IDF described here. Photo: Reforma.imufomot, Wikimedia Commons, public domain.Adjustment screw diagramTypical IDF-XE layout: idle mixture, idle speed and air-bypass screws. Original simplified schematic for Tuning Wiki, CC BY 4.0, based on Redline’s IDF-XE control reference; not to scale, and variants or linkages may differ.View Redline's IDF-XE adjustment-control diagram. The diagram identifies the idle speed screw, separate idle mixture screws, air-bypass screws and locknuts, and accelerator-pump adjustment nut. The drawing is a typical IDF-XE layout; individual versions and linkage arrangements can differ.
Single centermount vs dual IDF note: CB Performance notes that when a single 40/44/48 IDF is mounted centrally on a plenum manifold (rather than in dual individual-runner pairs), airflow and vacuum distribution change markedly: single centermount setups commonly require larger main and idle jets, 000 pump bypass (closed), an F7 emulsion tube (Aircooled.Net), and a 2 mm hole drilled in each throttle butterfly to stabilise idle airflow.
2. Fuel pressure & float level
Fuel pressure: Redline Weber specifies 2.5–3 psi maximum; higher pressure causes bowl spillage and rich idling.
Float height: hold the top cover vertically with the gasket in place and tang resting lightly on the needle ball without compressing the spring. Typical settings are 10 mm closed / 32.5 mm drop on early brass-float 40 IDF and 12 mm closed on 40/44/48 IDF plastic floats (Bigorre float heights).
Off-road float drop limit: for rough off-road / Baja use, Redline recommends limiting maximum float drop to 15.5 mm.
3. IDF tuning approach
Bench prep & air-bypass screws: disconnect cross-linkage before tuning. Loosen the 8 mm locknuts on the idle air-bypass screws, seat them lightly shut, and lock the nuts (Redline IDF controls).
Speed screw & Lean Best Idle: set idle speed screws ¼–½ turn in after touching the lever (never wind them open past ½ turn, or the butterfly exposes progression holes at idle). Lightly seat each mixture screw and back out 1 full turn; adjust each barrel individually to fastest, smoothest idle.
Synchronise & verify idle jet size: match airflow across barrels/carbs by bringing the higher-flowing carb down to the lower-flowing carb. If best idle needs more than 1½ turns out, step up half an idle-jet size; if ½ turn or less, step down half a size (Redline IDF addendum).
Main circuit & emulsion tubes: IDF uses the same 73401 (41110.001) main jets, 77401 air correctors, and emulsion tubes as DCOE (most dual 40/44 IDF street builds use F11, moving to F2 or F7 on larger bores/centermounts). Use the pump bypass jet (e.g. 55 vs 000 closed) to adjust how much accelerator-pump fuel returns to the bowl rather than squirting into the throat.
4. Related pages
Weber carburettor tuning overview
Weber DCOE and DCO-SP carburettors: specs and tuning
Weber IDA and IDA 3C carburettors: specs and tuning
Carburettor synchronisation, faults and rebuilds
Open each version to inspect formatting, tables and photographs.
Revision 1: Weber IDF carburettors: specs and tuning
The Weber IDF series (36, 40, 44 and 48 IDF) is a vertical downdraft twin-choke individual-runner carburettor sharing the same emulsion-tube and main/air-jet architecture as the sidedraft DCOE, packaged for V-engines, boxer engines (air-cooled VW Type 1 / Type 4, Porsche 356/912) and tight engine bays (Alfa Romeo, Fiat, Ford).
1. Models & factory baseline jetting
Model
Factory choke / aux
Main jet
Emulsion tube
Air corrector
Idle jet
Pump jet / bypass
40 IDF 70
28 mm / 4.5
115
F11
200
50
50 / 55 bypass (1.75 needle)
44 IDF 71
36 mm / 4.5
135
F11
175
50
50 / 55 bypass (1.75 needle)
48 IDF 6
40 mm / 4.5
150
F2
180
55
50 / 000 bypass (2.00 needle)
Single centermount vs dual IDF note:CB Performance notes that when a single 40/44/48 IDF is mounted centrally on a plenum manifold (rather than in dual individual-runner pairs), airflow and vacuum distribution change markedly: single centermount setups commonly require larger main and idle jets, 000 pump bypass (closed), an F7 emulsion tube (Aircooled.Net), and a 2 mm hole drilled in each throttle butterfly to stabilise idle airflow.
Float height: hold the top cover vertically with the gasket in place and tang resting lightly on the needle ball without compressing the spring. Typical settings are 10 mm closed / 32.5 mm drop on early brass-float 40 IDF and 12 mm closed on 40/44/48 IDF plastic floats (Bigorre float heights).
Off-road float drop limit: for rough off-road / Baja use, Redline recommends limiting maximum float drop to 15.5 mm.
3. IDF tuning approach
Bench prep & air-bypass screws: disconnect cross-linkage before tuning. Loosen the 8 mm locknuts on the idle air-bypass screws, seat them lightly shut, and lock the nuts (Redline IDF controls).
Speed screw & Lean Best Idle: set idle speed screws ¼–½ turn in after touching the lever (never wind them open past ½ turn, or the butterfly exposes progression holes at idle). Lightly seat each mixture screw and back out 1 full turn; adjust each barrel individually to fastest, smoothest idle.
Synchronise & verify idle jet size: match airflow across barrels/carbs by bringing the higher-flowing carb down to the lower-flowing carb. If best idle needs more than 1½ turns out, step up half an idle-jet size; if ½ turn or less, step down half a size (Redline IDF addendum).
Main circuit & emulsion tubes: IDF uses the same 73401 (41110.001) main jets, 77401 air correctors, and emulsion tubes as DCOE (most dual 40/44 IDF street builds use F11, moving to F2 or F7 on larger bores/centermounts). Use the pump bypass jet (e.g. 55 vs 000 closed) to adjust how much accelerator-pump fuel returns to the bowl rather than squirting into the throat.
Revision 6: Weber IDF carburettors: specs and tuning
The Weber IDF series (36, 40, 44 and 48 IDF) is a vertical downdraft twin-choke individual-runner carburettor sharing the same emulsion-tube and main/air-jet architecture as the sidedraft DCOE, packaged for V-engines, boxer engines (air-cooled VW Type 1 / Type 4, Porsche 356/912) and tight engine bays (Alfa Romeo, Fiat, Ford).
For comparison: a Weber 48 IDA downdraft carburettor, a different model from the IDF described here. Photo: Reforma.imufomot, Wikimedia Commons, public domain.
Adjustment screw diagram
Typical IDF-XE layout: idle mixture, idle speed and air-bypass screws. Original simplified schematic for Tuning Wiki, CC BY 4.0, based on Redline’s IDF-XE control reference; not to scale, and variants or linkages may differ.
View Redline's IDF-XE adjustment-control diagram. The diagram identifies the idle speed screw, separate idle mixture screws, air-bypass screws and locknuts, and accelerator-pump adjustment nut. The drawing is a typical IDF-XE layout; individual versions and linkage arrangements can differ.
1. Models & factory baseline jetting
Model
Factory choke / aux
Main jet
Emulsion tube
Air corrector
Idle jet
Pump jet / bypass
40 IDF 70
28 mm / 4.5
115
F11
200
50
50 / 55 bypass (1.75 needle)
44 IDF 71
36 mm / 4.5
135
F11
175
50
50 / 55 bypass (1.75 needle)
48 IDF 6
40 mm / 4.5
150
F2
180
55
50 / 000 bypass (2.00 needle)
Single centermount vs dual IDF note:CB Performance notes that when a single 40/44/48 IDF is mounted centrally on a plenum manifold (rather than in dual individual-runner pairs), airflow and vacuum distribution change markedly: single centermount setups commonly require larger main and idle jets, 000 pump bypass (closed), an F7 emulsion tube (Aircooled.Net), and a 2 mm hole drilled in each throttle butterfly to stabilise idle airflow.
Float height: hold the top cover vertically with the gasket in place and tang resting lightly on the needle ball without compressing the spring. Typical settings are 10 mm closed / 32.5 mm drop on early brass-float 40 IDF and 12 mm closed on 40/44/48 IDF plastic floats (Bigorre float heights).
Off-road float drop limit: for rough off-road / Baja use, Redline recommends limiting maximum float drop to 15.5 mm.
3. IDF tuning approach
Bench prep & air-bypass screws: disconnect cross-linkage before tuning. Loosen the 8 mm locknuts on the idle air-bypass screws, seat them lightly shut, and lock the nuts (Redline IDF controls).
Speed screw & Lean Best Idle: set idle speed screws ¼–½ turn in after touching the lever (never wind them open past ½ turn, or the butterfly exposes progression holes at idle). Lightly seat each mixture screw and back out 1 full turn; adjust each barrel individually to fastest, smoothest idle.
Synchronise & verify idle jet size: match airflow across barrels/carbs by bringing the higher-flowing carb down to the lower-flowing carb. If best idle needs more than 1½ turns out, step up half an idle-jet size; if ½ turn or less, step down half a size (Redline IDF addendum).
Main circuit & emulsion tubes: IDF uses the same 73401 (41110.001) main jets, 77401 air correctors, and emulsion tubes as DCOE (most dual 40/44 IDF street builds use F11, moving to F2 or F7 on larger bores/centermounts). Use the pump bypass jet (e.g. 55 vs 000 closed) to adjust how much accelerator-pump fuel returns to the bowl rather than squirting into the throat.