The Weber DCOE (Doppio Corpo Orizzontale, double-body horizontal) and racing DCO/SP series are synchronous twin-choke sidedraft carburettors. Almost always installed so each throttle barrel feeds one individual cylinder runner, they combine interchangeable main venturis, auxiliary venturis, emulsion wells, idle progression jets and mechanical accelerator pumps in a compact alloy casting.
1. Choke (venturi) & barrel sizing
Power potential and low-RPM tractability are governed primarily by the removable main venturi (choke), not the outer barrel diameter (Dave Andrews Weber DCOE guide). Ideal throttle-barrel size is approximately venturi size × 1.25 (for example, a 36 mm choke pairs ideally with a 45 DCOE, though a 40 DCOE can also fit a 36 mm choke).
| Model | Available chokes | Factory baseline example (choke / main / em. tube / air / idle / pump / needle) |
|---|---|---|
| 40 DCOE 151 | 24–36 mm | 32 mm / 115 / F11 / 200 / 45F9 / 40 pump (50 bleed) / 1.75 |
| 42 DCOE | 24–34 mm | 32 mm / 135 / F15 / 155 / 55F2 / 45 pump / 2.00 (Maserati 3500 GT) |
| 45 DCOE 152 | 28–40 mm | 36 mm / 145 / F16 / 155 / 55F8 / 45 pump (40 bleed) / 2.00 |
| 48 DCOE | 40–42 mm | 42 mm / 180 / F9 / 160 / 60F8 / 45 pump (100 bleed) / 2.50 |
| 48 / 50 DCO/SP | 42–46 mm | 42 or 46 mm / 180 / F7 / 160 / 65F8 / 45 pump (100 bleed) / 2.50 |
| 55 DCO/SP | 46–48 mm | 48 mm / 180 / F9 / 180 / 60F8 / 45 pump (100 bleed) / 2.50 |
2. Float level & fuel pressure
- Fuel pressure: keep regulated delivery pressure around
2.5–3 psi; excessive pump pressure forces fuel past the needle valve and floods the auxiliary venturis. - Dry float height (lid vertical, gasket fitted, tang touching ball without compressing spring):
- 40 / 45 DCOE brass float: typically
8–9 mmclosed /14–15 mmdrop (5–8 mmon some early 45 DCOE models; verify exact float weight and casting type). - 40 / 45 DCOE / DCO-SP plastic float: typically
12.5 mmclosed /25 mmdrop (12 mmon 48/50/55 DCO/SP plastic float, Bigorre float chart; Pierce Manifolds).
- 40 / 45 DCOE brass float: typically
- Wet fuel-level check: with the emulsion tube removed, an acrylic optical depth gauge in the emulsion well typically reads
25 mm ± 1 mmbelow the top deck (Weber DCOE reference).
3. Idle, progression & the 2,500–3,000 rpm stumble
- Close air-bypass screws first: on late emissions-type
DCOE 151/152bodies with air-bleed bypass screws under 8 mm locknuts, lightly seat them closed before base idle setup. - Idle speed stop & Lean Best Idle: keep the idle speed stop no more than
¼–½ turnpast contact (so the throttle butterfly does not uncover progression holes at idle). Start mixture screws at1 turnout (2.5 turnson coarse-thread early DCOEs). Tune each barrel individually for smoothest, fastest idle. - Synchronise carbs: match airflow with a Synchrometer or Uni-Syn by bringing the higher-flowing carb down to the lower-flowing carb, then adjust both evenly to target idle (
900–1,100 rpmon cammed engines). - Fix 2,500–3,000 rpm stumble with the
F-bleed: Webcon UK notes that the DCOE idle jet's numeric prefix (e.g.50=0.50 mm) sets idle fuel flow so the mixture screw sits around1–3 turnsout, whereas theF-number sets the side air-bleed hole controlling upper progression just before the main circuit cuts in. Keep the fuel number fixed and step betweenF8(1.2 mm, leanest),F9(1.0 mm, standard start) andF6(0.7 mm, richest) to cure a lean misfire or rich stumble around2,500–3,000 rpm.
4. Main jet, emulsion tube & air corrector tuning
- Starting formulas:
main jet ≈ venturi (mm) × 4;air corrector ≈ main jet + 50. - Emulsion tubes by cylinder size:
250–325 cc→F11;275–400 cc→F15;350–475 cc→F9orF16;450–575 cc→F2. - Splitting roles: tune the main jet (Weber
41110.001) for full-load mid-to-upper RPM AFR, then use the air corrector (77401/41360series) to flatten the top-end slope (larger leans high RPM, smaller enriches high RPM).
5. Related pages
- Weber carburettor tuning overview
- Weber IDF carburettors: specs and tuning
- Weber IDA and IDA 3C carburettors: specs and tuning
- Carburettor synchronisation, faults and rebuilds