Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Simos 18
Applies to
Simos 18.1
Tool groups
None
Manufacturers
Volkswagen Group

Scope. The examples below use the community SC8S5031_C_OEM Simos 18.1 cross-reference. Exact injection hardware, ECU software, operating mode, pulse numbering, angle reference, conversion and limits must be verified on the vehicle. Some extracted descriptions conflict; names and representable ranges are not recommended values. This guide concerns high-pressure direct injection (HPDI); see the separate MPI injection timing and phasing guide for port injection.

Start, end and duration

Start of injection (SOI) and end of injection (EOI) refer to different points in an injection event. Injection duration is a time; its crank-angle span grows with engine speed. At constant speed, a 1 ms interval spans 0.006 × rpm crank degrees: at 6,000 rpm that is 36°. This is arithmetic for the time interval, not an injector flow, allowed window, or recommended timing. Electrical command, actual needle motion and delivered fuel can differ.

The ECU may schedule different pulses and select different maps during startup, catalyst heating, normal operation or combined direct/port modes. A logged value must be interpreted with its injector, pulse, operating mode and crank-angle convention. “Higher” or “lower” on an angle display does not automatically mean earlier or later without the definition's reference and direction. The SC8S5031 INJR adaptation reference exposes different TDC-related and internal coordinate representations; do not compare their numeric values until the conversion is established.

Example SOI and separation maps

  • ip_soi_1_opp_1_cus is described as first-pulse SOI for single injection in the TDC-related representation, in crank-angle degrees, against predicted cylinder air mass m_air_cyl_pred in mg/stroke and injection speed n_inj in rpm. ip_soi_1_opp_1_cast_cus is the cold-phasing counterpart. Confirm which operating mode and representation the file actually uses. INJR adaptation reference.
  • ip_soi_1_ch_1_cus describes first-pulse SOI for single injection during catalyst heating, with predicted air mass and injection speed axes. Other entries describe multiple-pulse and combined-mode cases; existence in the definition does not prove those modes are used on every vehicle.
  • ip_crk_delta_1_2_opp_2 is a crank-angle difference between first and second injections for a double-injection path, against predicted cylinder air mass and injection speed. ip_crk_2_3_opp_3_homs_s similarly describes the second-to-third angle difference for a triple-injection path. Verify pulse indexing and how the scheduler applies the separation; these are not duration maps. INJR injection-phase application reference.
  • ip_ang_ofs_fup_inj_1_opp is a first-pulse phase offset against high fuel pressure fup_h in hPa; corresponding second- and third-pulse offsets are listed. This is an angle correction, not a rail-pressure setpoint.

Window and runtime signals

The adaptation reference describes ip_soi_max_cus as an earliest-SOI curve against engine speed. ip_eoi_min_hom_fup_cor is a fuel-pressure-dependent EOI-limit correction in the single-pulse path, while ip_eoi_lim_ofs_iga is an offset between ignition and latest EOI for selected combustion modes and engine speed. These describe constraints and corrections, not a complete safe injection window for every mode. Maintain the ECU's limits and verify the active path. INJR phase and limits.

ang_inj_sp[0][2][3] and ang_inj[0][2][3] are injection-angle request and applied runtime quantities in the reference; the field can represent SOI or EOI according to the mode. eoi_mes_cus[2][3] is described as estimated performed EOI. These are runtime signals, not calibration maps, and estimated timing is not proof of actual spray or mixture distribution. Verify indices, source and logger sampling. INJR adaptation and measurements.

Diagnosis and hardware changes

  1. Record ECU identifiers, injector and pump hardware, fuel, rail pressure, engine speed, operating mode and cylinder-specific faults. Confirm the sensor and injection-system health before attributing a complaint to timing.
  2. Where supported, compare injection mode and pulse widths, SOI/EOI and end limit, commanded and measured rail pressure, lambda target and actual, trims and per-cylinder misfire/knock data. COBB's MQB monitor list names per-cylinder primary and secondary SOI/EOI and an Injection Time Window Exceeded channel, but support and semantics depend on the product and vehicle.
  3. Increasing commanded fuel or changing fuel hardware can alter the time needed to deliver fuel and its relation to available injection windows. Pressure, injector characterization and pulse selection all matter. A single pulse-width log or a wideband lambda reading does not validate every cylinder's delivered mixture or combustion.
  4. Use the correct manufacturer procedures for high-pressure fuel work and maintain phase and component-protection limits. The MHH Auto Simos 18 tuning discussion contains participant reports about injection-window behavior; these are unverified observations, not universal angle or pressure recipes.

Related: direct injection and fuel pressure · MPI injection timing and phasing · MPI combustion modes · lambda control.

Sources