Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Simos 8.4 and 8.5
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 8

Removed text is struck through; added text is highlighted.

Simos 8.4 is a Siemens/Continental petrol ECU variant listed for some supercharged 3.0 V6 TFSI applications. Identify the ECU and exact software before selecting a file or map definition. The wider Simos 8.4 and 8.5 overview explains the documented engine system and the limits of application evidence.

ProcessorAutoTuner's ECU compatibility export of 28 October 2026 lists the Infineon TC1796 as the microcontroller of Simos 8.4. This is a tool-vendor listing, not manufacturer documentation, and it does not state the flash or EEPROM configuration.

Identification and the calibration

Alientech's vehicle list associates a 2012 Audi S4 Avant 3.0 TFSI CAKA with Simos 8.4. This is one product's application entry, not a universal mapping from engine code to ECU. Record the controller label, hardware and software numbers, calibration and gearbox on the actual vehicle.

For one specific file, a commercial map-pack listing for 8K0907551 0005 identifies an Audi S5 3.0 and advertises labelled groups for torque, air control, spark, injection and rail pressure. The vendor says the pack is a CSV map export, not a DAMOS or A2L. Its names and scaling are seller claims and were not independently checked here; this listing does not establish locations or functions in other software. Compare the actual read and definition, then verify axes, units and operation before editing.

The seller's list for 8K0907551 0005 distinguishes low- and high-speed torque-request groups, labels separate automatic-transmission request groups, and lists gear-dependent and clutch-protection torque limiters. It also lists requested engine load, lambda for component protection and rail-pressure groups. These are useful search terms for reviewing that seller's definition, not proof of a map's active operating mode or function. The public list gives names, and the seller also displays one illustrative table; the complete export's sizes, axes and positions are offered in the CSV. Neither the list nor the seller's labels establish that an individual map needs changing.A displayed torque-to-load exampleThe same seller’s public example labels one table “Requested engine load”, with 12 torque columns in Nm, 16 engine-speed rows in rpm and values in mg/st. At 3,008 rpm, its displayed cells for 300 and 440 Nm are 485 and 755 mg/st, respectively. This illustrates the seller’s proposed torque-to-load relationship for the advertised file; these cells are neither measured air charge nor recommended targets.The table’s label, axis scaling and source have not been independently verified against that original binary. A displayed cell does not prove that the ECU selected the table, that its inputs matched the nominal breakpoints, or that a specific requested torque was delivered. Match the complete file and definition, verify units and selection conditions, and compare requests and actual behaviour in a suitable log before drawing a conclusion. Other software and operating modes may use different tables.

Torque and air as an investigation

In the indexed Simos 8.4 Stage 1 project, participants describe torque requests and limits alongside air-mass and pressure functions. A later post presents an interpretation in which pedal demand leads to a clutch torque request and then an air-mass setpoint. This is a community explanation for the files being discussed, not a verified universal control diagram. Requested, limited, estimated and measured quantities should be kept distinct.

In a 2010 S4 manual discussion, an owner reported a specified pressure that tapered at higher speed despite a higher torque request. A reply suggested that the maps being investigated included limits for different transmissions and that air-mass limits also merited checking. The report does not prove which limiter was active or that the same diagnosis applies to another software version. Direct forum access was unavailable when this page was prepared; the indexed discussion was reviewed.

A practical investigation starts by recording the file and gearbox, baseline health, fuel, supercharger pulley and cooling system. With supported channels, compare pedal, torque request and any active torque or load limit, pressure request and actual pressure, throttle and bypass position, then lambda, fuel-pressure target and actual, ignition timing, knock correction and temperatures. Distinguish absolute and relative pressure, and confirm whether each channel is measured, modelled or requested. A raised limit does not itself establish increased airflow or safe combustion.

On the CAJA 3.0 TFSI described in Audi SSP 437, a belt-driven Roots supercharger uses a bypass flap and pressure-based air-mass calculation. The SSP calls the ECU Simos 8 without identifying an 8.4 suffix, so its system description is context, not proof of an exact 8.4 calibration. Inspect the actual installation.

For APR’s Simos 8.4 logging examples and the factory 3.0 TFSI bypass, pressure-sensor and charge-cooling context, see Simos 8.4 charge-air and bypass log review.

Community examples of calibration labelsIn a forum discussion of a Q7 described as Simos 8.33, a contributor identifies ip_flow_vol_scha_bas_1 as a supercharger basic-volume-flow map, ip_maf_max_stnd_vvl as an intake-air maximum for different valve lifts, and ip_map_max_pow_lim as a manifold-pressure limit for the air-mass setpoint. These are the contributor's interpretations for the files under discussion, not independently verified descriptions for the S5 8K0907551 0005 example above. Another participant disagreed about the effect of changing the first map and discussed the relationship of air and gear-dependent clutch torque limits. Neither viewpoint establishes which limit is active on a particular ECU or which maps must be changed.In the same discussion an owner reports first using the wrong stock-file revision while constructing a definition, and later says maps for an E revision did not work directly with C and D revisions. This is a useful illustration of file-matching risk, not a complete software compatibility determination. Identify the actual hardware, full software and file layout; validate symbol, axis, scaling and conditions against the loaded file before any controlled test. Similar labels or neighboring tables do not prove function, and an ECU-reported torque increase is not an independent torque measurement. Nefarious Motorsports discussion, replies 64–73.

Programming

Programming, logging, calibration editing and a usable recovery read are separate capabilities. Confirm the selected tool's operation for the exact hardware and software, checksum handling and recovery method before writing. Preserve protection functions and resolve mechanical or diagnostic faults rather than treating every restriction as a map to remove.

Product-specific controller and calibration selectionThe 034Motorsport Dynamic+ Portal guide illustrates its own OBD programming workflow with a demonstration screen identifying the engine controller as Simos 8.4, 8K0907551D 0003 alongside a separate DL501 G2 transmission controller, 8K2927156D 0004. This is a screenshot from one product’s guide, not independent evidence that those controllers or calibrations are fitted together in another car. It illustrates the need to identify and select the engine and transmission controllers separately.The same illustration presents multiple calibration groups and fuel/feature variants. Their names and displayed features are 034Motorsport product options, not factory Simos functions or an instruction to raise a limit. The guide says to match the selected file to its hardware and fuel requirements; verify the octane scale and current availability with that provider. Its Q&A says some applications require an OEM update before the performance file and recommends its Stock variant when an existing tune is uncertain. These are product-specific procedures. A provider’s stock file or update does not establish that the vehicle’s previous modified calibration or all ECU memory has been saved. Record the original identity and file provenance, confirm the operation and a suitable recovery path, and follow current tool instructions for the exact controller.See Simos 8 supercharged 3.0 TFSI fuel pressure and lambda log review for fuel-system and bank-mixture diagnosis.

Sources

Alientech Powergate vehicle list. Product-specific 8.4 application example. Accessed 17 November 2026. Audi Self-Study Programme 437: 3.0 V6 TFSI with Roots blower. Engine system and Simos 8 family context, without a variant suffix. Accessed 17 November 2026. Auto-Remap 8K0907551 0005 map-pack listing. Commercial, file-specific labels and advertised coverage; not independently validated. Accessed 17 November 2026. Nefarious Motorsports Simos 8.4 Stage 1 project, including the 2010 S4 manual discussion. Community observations, hypotheses and file-specific examples; direct access unavailable, indexed discussion reviewed 17 November 2026. AutoTuner ECU compatibility list (PDF export dated 28 October 2026). AutoTuner; tool-vendor listing of ECU type and microcontroller. Accessed 19 November 2026.Alientech Powergate vehicle list. Product-specific 8.4 application example. Accessed 17 November 2026. Audi Self-Study Programme 437: 3.0 V6 TFSI with Roots blower. Engine system and Simos 8 family context, without a variant suffix. Accessed 17 November 2026. Auto-Remap 8K0907551 0005 map-pack listing. Commercial, file-specific labels and advertised coverage; not independently validated. Accessed 17 November 2026. Nefarious Motorsports Simos 8.4 Stage 1 project, including the 2010 S4 manual discussion. Community observations, hypotheses and file-specific examples; direct access unavailable, indexed discussion reviewed 17 November 2026.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: Simos 8.4

Simos 8.4 is a Siemens/Continental petrol ECU variant listed for some supercharged 3.0 V6 TFSI applications. Identify the ECU and exact software before selecting a file or map definition. The wider Simos 8.4 and 8.5 overview explains the documented engine system and the limits of application evidence.

Identification and the calibration

Alientech's vehicle list associates a 2012 Audi S4 Avant 3.0 TFSI CAKA with Simos 8.4. This is one product's application entry, not a universal mapping from engine code to ECU. Record the controller label, hardware and software numbers, calibration and gearbox on the actual vehicle.

For one specific file, a commercial map-pack listing for 8K0907551 0005 identifies an Audi S5 3.0 and advertises labelled groups for torque, air control, spark, injection and rail pressure. The vendor says the pack is a CSV map export, not a DAMOS or A2L. Its names and scaling are seller claims and were not independently checked here; this listing does not establish locations or functions in other software. Compare the actual read and definition, then verify axes, units and operation before editing.

Torque and air as an investigation

In the indexed Simos 8.4 Stage 1 project, participants describe torque requests and limits alongside air-mass and pressure functions. A later post presents an interpretation in which pedal demand leads to a clutch torque request and then an air-mass setpoint. This is a community explanation for the files being discussed, not a verified universal control diagram. Requested, limited, estimated and measured quantities should be kept distinct.

In a 2010 S4 manual discussion, an owner reported a specified pressure that tapered at higher speed despite a higher torque request. A reply suggested that the maps being investigated included limits for different transmissions and that air-mass limits also merited checking. The report does not prove which limiter was active or that the same diagnosis applies to another software version. Direct forum access was unavailable when this page was prepared; the indexed discussion was reviewed.

A practical investigation starts by recording the file and gearbox, baseline health, fuel, supercharger pulley and cooling system. With supported channels, compare pedal, torque request and any active torque or load limit, pressure request and actual pressure, throttle and bypass position, then lambda, fuel-pressure target and actual, ignition timing, knock correction and temperatures. Distinguish absolute and relative pressure, and confirm whether each channel is measured, modelled or requested. A raised limit does not itself establish increased airflow or safe combustion.

On the CAJA 3.0 TFSI described in Audi SSP 437, a belt-driven Roots supercharger uses a bypass flap and pressure-based air-mass calculation. The SSP calls the ECU Simos 8 without identifying an 8.4 suffix, so its system description is context, not proof of an exact 8.4 calibration. Inspect the actual installation.

For APR’s Simos 8.4 logging examples and the factory 3.0 TFSI bypass, pressure-sensor and charge-cooling context, see Simos 8.4 charge-air and bypass log review.

Programming

Programming, logging, calibration editing and a usable recovery read are separate capabilities. Confirm the selected tool's operation for the exact hardware and software, checksum handling and recovery method before writing. Preserve protection functions and resolve mechanical or diagnostic faults rather than treating every restriction as a map to remove.

Sources

Revision 8: Simos 8.4

Simos 8.4 is a Siemens/Continental petrol ECU variant listed for some supercharged 3.0 V6 TFSI applications. Identify the ECU and exact software before selecting a file or map definition. The wider Simos 8.4 and 8.5 overview explains the documented engine system and the limits of application evidence.

Processor

AutoTuner's ECU compatibility export of 28 October 2026 lists the Infineon TC1796 as the microcontroller of Simos 8.4. This is a tool-vendor listing, not manufacturer documentation, and it does not state the flash or EEPROM configuration.

Identification and the calibration

Alientech's vehicle list associates a 2012 Audi S4 Avant 3.0 TFSI CAKA with Simos 8.4. This is one product's application entry, not a universal mapping from engine code to ECU. Record the controller label, hardware and software numbers, calibration and gearbox on the actual vehicle.

For one specific file, a commercial map-pack listing for 8K0907551 0005 identifies an Audi S5 3.0 and advertises labelled groups for torque, air control, spark, injection and rail pressure. The vendor says the pack is a CSV map export, not a DAMOS or A2L. Its names and scaling are seller claims and were not independently checked here; this listing does not establish locations or functions in other software. Compare the actual read and definition, then verify axes, units and operation before editing.

The seller's list for 8K0907551 0005 distinguishes low- and high-speed torque-request groups, labels separate automatic-transmission request groups, and lists gear-dependent and clutch-protection torque limiters. It also lists requested engine load, lambda for component protection and rail-pressure groups. These are useful search terms for reviewing that seller's definition, not proof of a map's active operating mode or function. The public list gives names, and the seller also displays one illustrative table; the complete export's sizes, axes and positions are offered in the CSV. Neither the list nor the seller's labels establish that an individual map needs changing.

A displayed torque-to-load example

The same seller’s public example labels one table “Requested engine load”, with 12 torque columns in Nm, 16 engine-speed rows in rpm and values in mg/st. At 3,008 rpm, its displayed cells for 300 and 440 Nm are 485 and 755 mg/st, respectively. This illustrates the seller’s proposed torque-to-load relationship for the advertised file; these cells are neither measured air charge nor recommended targets.

The table’s label, axis scaling and source have not been independently verified against that original binary. A displayed cell does not prove that the ECU selected the table, that its inputs matched the nominal breakpoints, or that a specific requested torque was delivered. Match the complete file and definition, verify units and selection conditions, and compare requests and actual behaviour in a suitable log before drawing a conclusion. Other software and operating modes may use different tables.

Torque and air as an investigation

In the indexed Simos 8.4 Stage 1 project, participants describe torque requests and limits alongside air-mass and pressure functions. A later post presents an interpretation in which pedal demand leads to a clutch torque request and then an air-mass setpoint. This is a community explanation for the files being discussed, not a verified universal control diagram. Requested, limited, estimated and measured quantities should be kept distinct.

In a 2010 S4 manual discussion, an owner reported a specified pressure that tapered at higher speed despite a higher torque request. A reply suggested that the maps being investigated included limits for different transmissions and that air-mass limits also merited checking. The report does not prove which limiter was active or that the same diagnosis applies to another software version. Direct forum access was unavailable when this page was prepared; the indexed discussion was reviewed.

A practical investigation starts by recording the file and gearbox, baseline health, fuel, supercharger pulley and cooling system. With supported channels, compare pedal, torque request and any active torque or load limit, pressure request and actual pressure, throttle and bypass position, then lambda, fuel-pressure target and actual, ignition timing, knock correction and temperatures. Distinguish absolute and relative pressure, and confirm whether each channel is measured, modelled or requested. A raised limit does not itself establish increased airflow or safe combustion.

On the CAJA 3.0 TFSI described in Audi SSP 437, a belt-driven Roots supercharger uses a bypass flap and pressure-based air-mass calculation. The SSP calls the ECU Simos 8 without identifying an 8.4 suffix, so its system description is context, not proof of an exact 8.4 calibration. Inspect the actual installation.

For APR’s Simos 8.4 logging examples and the factory 3.0 TFSI bypass, pressure-sensor and charge-cooling context, see Simos 8.4 charge-air and bypass log review.

Community examples of calibration labels

In a forum discussion of a Q7 described as Simos 8.33, a contributor identifies ip_flow_vol_scha_bas_1 as a supercharger basic-volume-flow map, ip_maf_max_stnd_vvl as an intake-air maximum for different valve lifts, and ip_map_max_pow_lim as a manifold-pressure limit for the air-mass setpoint. These are the contributor's interpretations for the files under discussion, not independently verified descriptions for the S5 8K0907551 0005 example above. Another participant disagreed about the effect of changing the first map and discussed the relationship of air and gear-dependent clutch torque limits. Neither viewpoint establishes which limit is active on a particular ECU or which maps must be changed.

In the same discussion an owner reports first using the wrong stock-file revision while constructing a definition, and later says maps for an E revision did not work directly with C and D revisions. This is a useful illustration of file-matching risk, not a complete software compatibility determination. Identify the actual hardware, full software and file layout; validate symbol, axis, scaling and conditions against the loaded file before any controlled test. Similar labels or neighboring tables do not prove function, and an ECU-reported torque increase is not an independent torque measurement. Nefarious Motorsports discussion, replies 64–73.

Programming

Programming, logging, calibration editing and a usable recovery read are separate capabilities. Confirm the selected tool's operation for the exact hardware and software, checksum handling and recovery method before writing. Preserve protection functions and resolve mechanical or diagnostic faults rather than treating every restriction as a map to remove.

Product-specific controller and calibration selection

The 034Motorsport Dynamic+ Portal guide illustrates its own OBD programming workflow with a demonstration screen identifying the engine controller as Simos 8.4, 8K0907551D 0003 alongside a separate DL501 G2 transmission controller, 8K2927156D 0004. This is a screenshot from one product’s guide, not independent evidence that those controllers or calibrations are fitted together in another car. It illustrates the need to identify and select the engine and transmission controllers separately.

The same illustration presents multiple calibration groups and fuel/feature variants. Their names and displayed features are 034Motorsport product options, not factory Simos functions or an instruction to raise a limit. The guide says to match the selected file to its hardware and fuel requirements; verify the octane scale and current availability with that provider. Its Q&A says some applications require an OEM update before the performance file and recommends its Stock variant when an existing tune is uncertain. These are product-specific procedures. A provider’s stock file or update does not establish that the vehicle’s previous modified calibration or all ECU memory has been saved. Record the original identity and file provenance, confirm the operation and a suitable recovery path, and follow current tool instructions for the exact controller.

See Simos 8 supercharged 3.0 TFSI fuel pressure and lambda log review for fuel-system and bank-mixture diagnosis.

Sources