Removed text is struck through; added text is highlighted.
This guide covers selected Jaguar-derived, belt-supercharged Land Rover and Range Rover petrol engines: the 3.0 AJ126 V6, 4.2 AJ33S V8 and 5.0 AJ133 V8. Their calibrations, charge-cooling systems and parts vary by model and year. Verify the vehicle and engine before using any example; a 3.0 supercharged V6 is not the newer turbocharged Ingenium straight-six.
Engine and ECU identification
Engine and exampleECU evidence and related wikiPractical distinction
4.2 supercharged V8, Range Rover/Range Rover SportA supplier identifies a Range Rover 4.2 AJ33S with Denso MB279700, HW NNN500411 and SW NV502089. File and map listing. See Denso petrol ECU overview, a generic family page rather than an MB279700-specific pinout.Land Rover's 2004 Sport launch specifies a 287 kW 4.2 supercharged and a separate naturally aspirated 4.4 V8. Check the fitted engine rather than the badge alone.
3.0 supercharged V6 AJ126, selected Discovery and Range RoverA Range Rover 3.0 AJ126 file is listed with Bosch MED17.8.31, software 1037549213 and calibration FPLA-14C204-TTC. This is one supplier-listed example.Land Rover describes a new supercharged V6 for 2014 Discovery. The supercharged V6 and the Ingenium hybrid I6 are different engines and controls.
5.0 supercharged V8 AJ133, selected Range Rover and SportA Range Rover 5.0 510 hp file is listed as Bosch MED17.8.31, hardware CPLA-12B684-YE, software 1037543516 and calibration DK62-14C204-RTD.Land Rover's 2011 Sport description identifies direct injection, a TVS supercharger and twin water-cooled intercoolers on a separate circuit. Naturally aspirated 5.0 versions require different parts and calibration.
The ECU links identify the relevant designation or family for the stated examples, not all cars with the same engine size. Record VIN, market, model year, engine code, ECU hardware and software numbers, current calibration, transmission, fuel and modifications. Verify the identification and the exact read/write method with the chosen tool's current support information. The same hardware label can carry different software; a calibration for one vehicle must not simply be flashed into another.
Baseline and diagnosis
Scan and save fault codes and live data before clearing anything. Investigate misfires, lean/rich corrections, sensor or boost/bypass faults and cooling warnings. Confirm the vehicle runs correctly in standard form.
Check service history, plugs and ignition coils, fuel delivery, air filters, hoses, charge-air leaks, engine cooling and oil condition. Test battery and charging stability before programming. Use the correct service procedure and components for the VIN.
Examine supercharger belt, tensioner, pulley alignment and bypass, and check for abnormal noise or mechanical play. On certain North American 2014 3.0 SC models, Land Rover bulletin LTB00669NAS1 discusses clatter caused by isolator wear and applies to the listed LR4, Range Rover and Sport VIN ranges. Follow the bulletin and current workshop procedures; the noise does not prove that diagnosis on every car.
Confirm charge-cooler pump operation, coolant level and flow, heat exchanger and hoses separately from the engine cooling circuit where fitted. Check for heat-soak-related power loss under repeated load.
On a suitable four-wheel-drive dynamometer, document baseline wheel and estimated crank power, fuel grade, ambient temperature and run conditions. Confirm the dyno setup is appropriate for the transfer case and stability systems.
Maps, functions and file-specific examples
Names below are third-party map-pack labels, not factory definitions. Their active logic, axes, scaling and units need independent verification against the exact ECU software; some functions may be represented by several interacting maps or strategies. A map list does not establish that every map is active in every condition.
Example fileWhat the seller listsWorkshop interpretation
4.2 Denso NNN500411 / NV502089Torque requests including automatic take-off, load and throttle, base spark and coolant correction, injection and speed limits.Assess driver request, torque model, throttle and fuelling together. Check temperature corrections and gearbox interactions rather than raising an isolated limit.
3.0 MED17.8.31 1037549213 / FPLA-14C204-TTCCategories listed include engine torque, limiters, injection, spark and air control.Confirm the map definition and units for the actual software, and calibrate to the installed supercharger drive, fuel and cooling system.
5.0 MED17.8.31 CPLA-12B684-YE / 1037543516Examples include gear-specific torque limits, torque request, requested lambda, component-protection lambda, spark advance and throttle/airflow.Maintain credible air and torque models, closed-loop and component protection, and transmission torque coordination. Log actual lambda, ignition corrections and fuel pressure.
For context, the 5.0 seller displays an “optimal spark advance” example with air charge and engine speed axes. At 2,000 rpm and a displayed 100% air-charge column the cell is 36.75 degrees. This is a seller-labelled value in one table of one file; it is not measured or final commanded spark and is not a tuning target or a safe value to copy. Final ignition depends on other maps, compensations, knock control and operating conditions.
Read and identify the original calibration and verify checksums and a practical recovery procedure before changing it. A calibration-only read may omit immobiliser data, EEPROM or other contents needed for full ECU recovery; an internet file is not proof of the vehicle's original configuration. Keep a record of all changes and avoid disabling protections or diagnostics to conceal faults.
How a supercharger package works
The blower is mechanically driven. A larger crank pulley or smaller supercharger pulley increases blower speed relative to engine speed, subject to the actual belt drive arrangement. More speed can increase airflow and charge temperature; manifold pressure depends on engine airflow, restrictions, bypass and operating conditions. A pressure reading alone is not a measure of combustion quality or safety.
Calibration-only: a tuner can adjust torque request and other appropriate calibration functions on a healthy vehicle using the intended fuel. Results depend on the original rating, drivetrain, temperature and calibration; independently measured gains are preferable to generic stage labels.
Pulley and calibration: Powerhouse's lower-pulley instructions cover specified AJ126 and AJ133 applications and explicitly require matched ECU remapping for that product. RENNtech describes a 5.0 package pairing a larger crank pulley with ECU software; David Appleby Engineering lists a V6 pulley and tune. These are examples, not universal fitment or promised power. Confirm part numbers, belt length and alignment, blower maximum speed, cooling, the tuner's fuel requirement and calibration before purchase. US pump-octane and UK RON labels are not numerically interchangeable.
Cooling and larger supercharger: confirm the standard charge-cooler circuit works first; then consider an appropriate heat exchanger, pump or reservoir package if testing shows sustained temperature is limiting the intended duty. A larger blower or a combined pulley package increases the need to verify rotor speed, fuel-system capacity, charge cooling, belt grip and calibration. Harrop's AJ133 TVS2300 installation guide is one example of a replacement-supercharger system requiring setup and dyno tuning. Verify fitment and supporting parts for the exact model.
Intake and exhaust changes require evidence of a restriction and testing; more noise does not establish a gain. Check clearance, filtration, catalyst compatibility and legal requirements. A standard cold-air feed and functioning charge cooler may outperform an intake that draws hot under-bonnet air.
Fuel, ignition and transmission
Agree a minimum fuel grade and use it consistently. A higher boost or load package must be calibrated against the available fuel, with adequate pump and injector headroom and functioning knock control. Monitor actual and requested lambda and pressure over a pull and during sustained load. Stoichiometric fuel trims in traffic do not prove high-load delivery is adequate. Do not copy another tuner's air/fuel ratio or timing figures: sensor position, fuel, conditions and calibration strategy matter.
Keep knock, misfire, coolant, intake-temperature and catalyst protection active. Investigate persistent cylinder-specific knock correction, abrupt throttle closure, high charge temperature, declining pressure or mismatch between requested and actual load. Check spark-plug and coil condition and use plug specifications recommended for the specific package and engine.
Identify the actual gearbox, service condition and torque-converter behaviour. Test kickdown, part-throttle shifts, full-load shifts and low-range use as appropriate, watching torque reduction requests. Additional engine torque increases demands on gearbox, transfer case, differentials, tyres, brakes and cooling. ZF notes that operating conditions and thermal load affect transmission oil life; service the actual unit to the applicable instructions. No universal safe torque figure is implied.
Validation and road use
On a suitable dyno, collect a consistent baseline and changed runs with the same fuel, gear strategy and corrections. Record actual versus requested lambda and load, fuel pressure, ignition and knock correction, charge temperature, coolant temperature and torque intervention where supported.
Validate idle, cold and hot starts, cruise, tip-in, overtaking, gear shifts and overrun as well as peak power. Repeat runs after heat soak and under the expected towing or sustained-load conditions. Stop and investigate a fault, misfire, unexpected heat or pressure drop.
Check belts, hoses, leaks, diagnostic codes and adaptations after testing. Provide the owner with fuel and service requirements, calibration identification and a measured before/after record.
Retain required emissions equipment and working diagnostics; verify applicable laws and insurance conditions. The Great Britain MOT inspection manual sets out current emissions inspection criteria.
Related wiki pages
See Land Rover engine failures and common problems for sourced timing-drive, crankshaft and Ingenium issues and service checks.
Land Rover petrol tuning and ECU identification.Bosch MED17.8.31 and Denso petrol ECU family.Eaton TVS R1900 supercharger and Supercharger types, drives and upgrades.Range Rover engines, Range Rover Sport engines and Discovery engines.
Open each version to inspect formatting, tables and photographs.
Revision 2: Land Rover 3.0 V6 and 4.2 and 5.0 V8 supercharged petrol tuning guide
This guide covers selected Jaguar-derived, belt-supercharged Land Rover and Range Rover petrol engines: the 3.0 AJ126 V6, 4.2 AJ33S V8 and 5.0 AJ133 V8. Their calibrations, charge-cooling systems and parts vary by model and year. Verify the vehicle and engine before using any example; a 3.0 supercharged V6 is not the newer turbocharged Ingenium straight-six.
Engine and ECU identification
| Engine and example | ECU evidence and related wiki | Practical distinction |
| 4.2 supercharged V8, Range Rover/Range Rover Sport | A supplier identifies a Range Rover 4.2 AJ33S with Denso MB279700, HW NNN500411 and SW NV502089. File and map listing. See Denso petrol ECU overview, a generic family page rather than an MB279700-specific pinout. | Land Rover's 2004 Sport launch specifies a 287 kW 4.2 supercharged and a separate naturally aspirated 4.4 V8. Check the fitted engine rather than the badge alone. |
| 3.0 supercharged V6 AJ126, selected Discovery and Range Rover | A Range Rover 3.0 AJ126 file is listed with Bosch MED17.8.31, software 1037549213 and calibration FPLA-14C204-TTC. This is one supplier-listed example. | Land Rover describes a new supercharged V6 for 2014 Discovery. The supercharged V6 and the Ingenium hybrid I6 are different engines and controls. |
| 5.0 supercharged V8 AJ133, selected Range Rover and Sport | A Range Rover 5.0 510 hp file is listed as Bosch MED17.8.31, hardware CPLA-12B684-YE, software 1037543516 and calibration DK62-14C204-RTD. | Land Rover's 2011 Sport description identifies direct injection, a TVS supercharger and twin water-cooled intercoolers on a separate circuit. Naturally aspirated 5.0 versions require different parts and calibration. |
The ECU links identify the relevant designation or family for the stated examples, not all cars with the same engine size. Record VIN, market, model year, engine code, ECU hardware and software numbers, current calibration, transmission, fuel and modifications. Verify the identification and the exact read/write method with the chosen tool's current support information. The same hardware label can carry different software; a calibration for one vehicle must not simply be flashed into another.
Baseline and diagnosis
- Scan and save fault codes and live data before clearing anything. Investigate misfires, lean/rich corrections, sensor or boost/bypass faults and cooling warnings. Confirm the vehicle runs correctly in standard form.
- Check service history, plugs and ignition coils, fuel delivery, air filters, hoses, charge-air leaks, engine cooling and oil condition. Test battery and charging stability before programming. Use the correct service procedure and components for the VIN.
- Examine supercharger belt, tensioner, pulley alignment and bypass, and check for abnormal noise or mechanical play. On certain North American 2014 3.0 SC models, Land Rover bulletin LTB00669NAS1 discusses clatter caused by isolator wear and applies to the listed LR4, Range Rover and Sport VIN ranges. Follow the bulletin and current workshop procedures; the noise does not prove that diagnosis on every car.
- Confirm charge-cooler pump operation, coolant level and flow, heat exchanger and hoses separately from the engine cooling circuit where fitted. Check for heat-soak-related power loss under repeated load.
- On a suitable four-wheel-drive dynamometer, document baseline wheel and estimated crank power, fuel grade, ambient temperature and run conditions. Confirm the dyno setup is appropriate for the transfer case and stability systems.
Maps, functions and file-specific examples
Names below are third-party map-pack labels, not factory definitions. Their active logic, axes, scaling and units need independent verification against the exact ECU software; some functions may be represented by several interacting maps or strategies. A map list does not establish that every map is active in every condition.
| Example file | What the seller lists | Workshop interpretation |
| 4.2 Denso NNN500411 / NV502089 | Torque requests including automatic take-off, load and throttle, base spark and coolant correction, injection and speed limits. | Assess driver request, torque model, throttle and fuelling together. Check temperature corrections and gearbox interactions rather than raising an isolated limit. |
| 3.0 MED17.8.31 1037549213 / FPLA-14C204-TTC | Categories listed include engine torque, limiters, injection, spark and air control. | Confirm the map definition and units for the actual software, and calibrate to the installed supercharger drive, fuel and cooling system. |
| 5.0 MED17.8.31 CPLA-12B684-YE / 1037543516 | Examples include gear-specific torque limits, torque request, requested lambda, component-protection lambda, spark advance and throttle/airflow. | Maintain credible air and torque models, closed-loop and component protection, and transmission torque coordination. Log actual lambda, ignition corrections and fuel pressure. |
For context, the 5.0 seller displays an “optimal spark advance” example with air charge and engine speed axes. At 2,000 rpm and a displayed 100% air-charge column the cell is 36.75 degrees. This is a seller-labelled value in one table of one file; it is not measured or final commanded spark and is not a tuning target or a safe value to copy. Final ignition depends on other maps, compensations, knock control and operating conditions.
Read and identify the original calibration and verify checksums and a practical recovery procedure before changing it. A calibration-only read may omit immobiliser data, EEPROM or other contents needed for full ECU recovery; an internet file is not proof of the vehicle's original configuration. Keep a record of all changes and avoid disabling protections or diagnostics to conceal faults.
How a supercharger package works
The blower is mechanically driven. A larger crank pulley or smaller supercharger pulley increases blower speed relative to engine speed, subject to the actual belt drive arrangement. More speed can increase airflow and charge temperature; manifold pressure depends on engine airflow, restrictions, bypass and operating conditions. A pressure reading alone is not a measure of combustion quality or safety.
Calibration-only: a tuner can adjust torque request and other appropriate calibration functions on a healthy vehicle using the intended fuel. Results depend on the original rating, drivetrain, temperature and calibration; independently measured gains are preferable to generic stage labels.
Pulley and calibration: Powerhouse's lower-pulley instructions cover specified AJ126 and AJ133 applications and explicitly require matched ECU remapping for that product. RENNtech describes a 5.0 package pairing a larger crank pulley with ECU software; David Appleby Engineering lists a V6 pulley and tune. These are examples, not universal fitment or promised power. Confirm part numbers, belt length and alignment, blower maximum speed, cooling, the tuner's fuel requirement and calibration before purchase. US pump-octane and UK RON labels are not numerically interchangeable.
Cooling and larger supercharger: confirm the standard charge-cooler circuit works first; then consider an appropriate heat exchanger, pump or reservoir package if testing shows sustained temperature is limiting the intended duty. A larger blower or a combined pulley package increases the need to verify rotor speed, fuel-system capacity, charge cooling, belt grip and calibration. Harrop's AJ133 TVS2300 installation guide is one example of a replacement-supercharger system requiring setup and dyno tuning. Verify fitment and supporting parts for the exact model.
Intake and exhaust changes require evidence of a restriction and testing; more noise does not establish a gain. Check clearance, filtration, catalyst compatibility and legal requirements. A standard cold-air feed and functioning charge cooler may outperform an intake that draws hot under-bonnet air.
Fuel, ignition and transmission
Agree a minimum fuel grade and use it consistently. A higher boost or load package must be calibrated against the available fuel, with adequate pump and injector headroom and functioning knock control. Monitor actual and requested lambda and pressure over a pull and during sustained load. Stoichiometric fuel trims in traffic do not prove high-load delivery is adequate. Do not copy another tuner's air/fuel ratio or timing figures: sensor position, fuel, conditions and calibration strategy matter.
Keep knock, misfire, coolant, intake-temperature and catalyst protection active. Investigate persistent cylinder-specific knock correction, abrupt throttle closure, high charge temperature, declining pressure or mismatch between requested and actual load. Check spark-plug and coil condition and use plug specifications recommended for the specific package and engine.
Identify the actual gearbox, service condition and torque-converter behaviour. Test kickdown, part-throttle shifts, full-load shifts and low-range use as appropriate, watching torque reduction requests. Additional engine torque increases demands on gearbox, transfer case, differentials, tyres, brakes and cooling. ZF notes that operating conditions and thermal load affect transmission oil life; service the actual unit to the applicable instructions. No universal safe torque figure is implied.
Validation and road use
- On a suitable dyno, collect a consistent baseline and changed runs with the same fuel, gear strategy and corrections. Record actual versus requested lambda and load, fuel pressure, ignition and knock correction, charge temperature, coolant temperature and torque intervention where supported.
- Validate idle, cold and hot starts, cruise, tip-in, overtaking, gear shifts and overrun as well as peak power. Repeat runs after heat soak and under the expected towing or sustained-load conditions. Stop and investigate a fault, misfire, unexpected heat or pressure drop.
- Check belts, hoses, leaks, diagnostic codes and adaptations after testing. Provide the owner with fuel and service requirements, calibration identification and a measured before/after record.
Retain required emissions equipment and working diagnostics; verify applicable laws and insurance conditions. The Great Britain MOT inspection manual sets out current emissions inspection criteria.
Related wiki pages
See Land Rover engine failures and common problems for sourced timing-drive, crankshaft and Ingenium issues and service checks.
Revision 2: Land Rover 3.0 V6 and 4.2 and 5.0 V8 supercharged petrol tuning guide
This guide covers selected Jaguar-derived, belt-supercharged Land Rover and Range Rover petrol engines: the 3.0 AJ126 V6, 4.2 AJ33S V8 and 5.0 AJ133 V8. Their calibrations, charge-cooling systems and parts vary by model and year. Verify the vehicle and engine before using any example; a 3.0 supercharged V6 is not the newer turbocharged Ingenium straight-six.
Engine and ECU identification
| Engine and example | ECU evidence and related wiki | Practical distinction |
| 4.2 supercharged V8, Range Rover/Range Rover Sport | A supplier identifies a Range Rover 4.2 AJ33S with Denso MB279700, HW NNN500411 and SW NV502089. File and map listing. See Denso petrol ECU overview, a generic family page rather than an MB279700-specific pinout. | Land Rover's 2004 Sport launch specifies a 287 kW 4.2 supercharged and a separate naturally aspirated 4.4 V8. Check the fitted engine rather than the badge alone. |
| 3.0 supercharged V6 AJ126, selected Discovery and Range Rover | A Range Rover 3.0 AJ126 file is listed with Bosch MED17.8.31, software 1037549213 and calibration FPLA-14C204-TTC. This is one supplier-listed example. | Land Rover describes a new supercharged V6 for 2014 Discovery. The supercharged V6 and the Ingenium hybrid I6 are different engines and controls. |
| 5.0 supercharged V8 AJ133, selected Range Rover and Sport | A Range Rover 5.0 510 hp file is listed as Bosch MED17.8.31, hardware CPLA-12B684-YE, software 1037543516 and calibration DK62-14C204-RTD. | Land Rover's 2011 Sport description identifies direct injection, a TVS supercharger and twin water-cooled intercoolers on a separate circuit. Naturally aspirated 5.0 versions require different parts and calibration. |
The ECU links identify the relevant designation or family for the stated examples, not all cars with the same engine size. Record VIN, market, model year, engine code, ECU hardware and software numbers, current calibration, transmission, fuel and modifications. Verify the identification and the exact read/write method with the chosen tool's current support information. The same hardware label can carry different software; a calibration for one vehicle must not simply be flashed into another.
Baseline and diagnosis
- Scan and save fault codes and live data before clearing anything. Investigate misfires, lean/rich corrections, sensor or boost/bypass faults and cooling warnings. Confirm the vehicle runs correctly in standard form.
- Check service history, plugs and ignition coils, fuel delivery, air filters, hoses, charge-air leaks, engine cooling and oil condition. Test battery and charging stability before programming. Use the correct service procedure and components for the VIN.
- Examine supercharger belt, tensioner, pulley alignment and bypass, and check for abnormal noise or mechanical play. On certain North American 2014 3.0 SC models, Land Rover bulletin LTB00669NAS1 discusses clatter caused by isolator wear and applies to the listed LR4, Range Rover and Sport VIN ranges. Follow the bulletin and current workshop procedures; the noise does not prove that diagnosis on every car.
- Confirm charge-cooler pump operation, coolant level and flow, heat exchanger and hoses separately from the engine cooling circuit where fitted. Check for heat-soak-related power loss under repeated load.
- On a suitable four-wheel-drive dynamometer, document baseline wheel and estimated crank power, fuel grade, ambient temperature and run conditions. Confirm the dyno setup is appropriate for the transfer case and stability systems.
Maps, functions and file-specific examples
Names below are third-party map-pack labels, not factory definitions. Their active logic, axes, scaling and units need independent verification against the exact ECU software; some functions may be represented by several interacting maps or strategies. A map list does not establish that every map is active in every condition.
| Example file | What the seller lists | Workshop interpretation |
| 4.2 Denso NNN500411 / NV502089 | Torque requests including automatic take-off, load and throttle, base spark and coolant correction, injection and speed limits. | Assess driver request, torque model, throttle and fuelling together. Check temperature corrections and gearbox interactions rather than raising an isolated limit. |
| 3.0 MED17.8.31 1037549213 / FPLA-14C204-TTC | Categories listed include engine torque, limiters, injection, spark and air control. | Confirm the map definition and units for the actual software, and calibrate to the installed supercharger drive, fuel and cooling system. |
| 5.0 MED17.8.31 CPLA-12B684-YE / 1037543516 | Examples include gear-specific torque limits, torque request, requested lambda, component-protection lambda, spark advance and throttle/airflow. | Maintain credible air and torque models, closed-loop and component protection, and transmission torque coordination. Log actual lambda, ignition corrections and fuel pressure. |
For context, the 5.0 seller displays an “optimal spark advance” example with air charge and engine speed axes. At 2,000 rpm and a displayed 100% air-charge column the cell is 36.75 degrees. This is a seller-labelled value in one table of one file; it is not measured or final commanded spark and is not a tuning target or a safe value to copy. Final ignition depends on other maps, compensations, knock control and operating conditions.
Read and identify the original calibration and verify checksums and a practical recovery procedure before changing it. A calibration-only read may omit immobiliser data, EEPROM or other contents needed for full ECU recovery; an internet file is not proof of the vehicle's original configuration. Keep a record of all changes and avoid disabling protections or diagnostics to conceal faults.
How a supercharger package works
The blower is mechanically driven. A larger crank pulley or smaller supercharger pulley increases blower speed relative to engine speed, subject to the actual belt drive arrangement. More speed can increase airflow and charge temperature; manifold pressure depends on engine airflow, restrictions, bypass and operating conditions. A pressure reading alone is not a measure of combustion quality or safety.
Calibration-only: a tuner can adjust torque request and other appropriate calibration functions on a healthy vehicle using the intended fuel. Results depend on the original rating, drivetrain, temperature and calibration; independently measured gains are preferable to generic stage labels.
Pulley and calibration: Powerhouse's lower-pulley instructions cover specified AJ126 and AJ133 applications and explicitly require matched ECU remapping for that product. RENNtech describes a 5.0 package pairing a larger crank pulley with ECU software; David Appleby Engineering lists a V6 pulley and tune. These are examples, not universal fitment or promised power. Confirm part numbers, belt length and alignment, blower maximum speed, cooling, the tuner's fuel requirement and calibration before purchase. US pump-octane and UK RON labels are not numerically interchangeable.
Cooling and larger supercharger: confirm the standard charge-cooler circuit works first; then consider an appropriate heat exchanger, pump or reservoir package if testing shows sustained temperature is limiting the intended duty. A larger blower or a combined pulley package increases the need to verify rotor speed, fuel-system capacity, charge cooling, belt grip and calibration. Harrop's AJ133 TVS2300 installation guide is one example of a replacement-supercharger system requiring setup and dyno tuning. Verify fitment and supporting parts for the exact model.
Intake and exhaust changes require evidence of a restriction and testing; more noise does not establish a gain. Check clearance, filtration, catalyst compatibility and legal requirements. A standard cold-air feed and functioning charge cooler may outperform an intake that draws hot under-bonnet air.
Fuel, ignition and transmission
Agree a minimum fuel grade and use it consistently. A higher boost or load package must be calibrated against the available fuel, with adequate pump and injector headroom and functioning knock control. Monitor actual and requested lambda and pressure over a pull and during sustained load. Stoichiometric fuel trims in traffic do not prove high-load delivery is adequate. Do not copy another tuner's air/fuel ratio or timing figures: sensor position, fuel, conditions and calibration strategy matter.
Keep knock, misfire, coolant, intake-temperature and catalyst protection active. Investigate persistent cylinder-specific knock correction, abrupt throttle closure, high charge temperature, declining pressure or mismatch between requested and actual load. Check spark-plug and coil condition and use plug specifications recommended for the specific package and engine.
Identify the actual gearbox, service condition and torque-converter behaviour. Test kickdown, part-throttle shifts, full-load shifts and low-range use as appropriate, watching torque reduction requests. Additional engine torque increases demands on gearbox, transfer case, differentials, tyres, brakes and cooling. ZF notes that operating conditions and thermal load affect transmission oil life; service the actual unit to the applicable instructions. No universal safe torque figure is implied.
Validation and road use
- On a suitable dyno, collect a consistent baseline and changed runs with the same fuel, gear strategy and corrections. Record actual versus requested lambda and load, fuel pressure, ignition and knock correction, charge temperature, coolant temperature and torque intervention where supported.
- Validate idle, cold and hot starts, cruise, tip-in, overtaking, gear shifts and overrun as well as peak power. Repeat runs after heat soak and under the expected towing or sustained-load conditions. Stop and investigate a fault, misfire, unexpected heat or pressure drop.
- Check belts, hoses, leaks, diagnostic codes and adaptations after testing. Provide the owner with fuel and service requirements, calibration identification and a measured before/after record.
Retain required emissions equipment and working diagnostics; verify applicable laws and insurance conditions. The Great Britain MOT inspection manual sets out current emissions inspection criteria.
Related wiki pages
See Land Rover engine failures and common problems for sourced timing-drive, crankshaft and Ingenium issues and service checks.