Page organisation in this revision
- Page type
- Technical article
- Subject
- ABS / DSC
- Parent
- AUMOVIO MK 100 UHP motorsport ABS
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- AUMOVIO
Changes from revision 1 to revision 1
Removed text is struck through; added text is highlighted.
Accessory connectors in AUMOVIO MK 100 UHP technical manual v2.1, figures 12–14, pages 17–18. These are accessory connector positions, not HECU positions. This applies to the described supplied kit hardware; check actual part numbers, connector orientation and revised supplier documentation.
Supplied PS20 external brake-pressure sensor
The manual identifies PS20 part 10.0522-9963. It warns against using a different external pressure sensor with this kit.
Sensor contactFunction1Ground2Signal output3Power supply positive
Supplied IMU connector
IMU contactFunction1Ground2CAN IMU low3CAN IMU high412 V supply
Supplied rotary mode switch
Switch pinWire colourUHP HECU connection1Red22, ABS_MODE_SW_SENSEEP2White23, ABS_MODE_SW_SIG3Black29, ABS_MODE_SW_GND
The manual warns to use the supplied switch. Consult the maker’s diagrams for connector face and orientation, and the separate HECU pinout for the ABS-only unit. Source: AUMOVIO MK 100 UHP technical manual v2.1, pages 17–18 and 22.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: AUMOVIO MK 100 UHP sensor and switch connector pinouts
Accessory connectors in AUMOVIO MK 100 UHP technical manual v2.1, figures 12–14, pages 17–18. These are accessory connector positions, not HECU positions. This applies to the described supplied kit hardware; check actual part numbers, connector orientation and revised supplier documentation.
Supplied PS20 external brake-pressure sensor
The manual identifies PS20 part 10.0522-9963. It warns against using a different external pressure sensor with this kit.
| Sensor contact | Function |
|---|
| 1 | Ground |
| 2 | Signal output |
| 3 | Power supply positive |
Supplied IMU connector
| IMU contact | Function |
|---|
| 1 | Ground |
| 2 | CAN IMU low |
| 3 | CAN IMU high |
| 4 | 12 V supply |
Supplied rotary mode switch
| Switch pin | Wire colour | UHP HECU connection |
|---|
| 1 | Red | 22, ABS_MODE_SW_SENSEEP |
| 2 | White | 23, ABS_MODE_SW_SIG |
| 3 | Black | 29, ABS_MODE_SW_GND |
The manual warns to use the supplied switch. Consult the maker’s diagrams for connector face and orientation, and the separate HECU pinout for the ABS-only unit. Source: AUMOVIO MK 100 UHP technical manual v2.1, pages 17–18 and 22.
Revision 1: AUMOVIO MK 100 UHP sensor and switch connector pinouts
Accessory connectors in AUMOVIO MK 100 UHP technical manual v2.1, figures 12–14, pages 17–18. These are accessory connector positions, not HECU positions. This applies to the described supplied kit hardware; check actual part numbers, connector orientation and revised supplier documentation.
Supplied PS20 external brake-pressure sensor
The manual identifies PS20 part 10.0522-9963. It warns against using a different external pressure sensor with this kit.
| Sensor contact | Function |
|---|
| 1 | Ground |
| 2 | Signal output |
| 3 | Power supply positive |
Supplied IMU connector
| IMU contact | Function |
|---|
| 1 | Ground |
| 2 | CAN IMU low |
| 3 | CAN IMU high |
| 4 | 12 V supply |
Supplied rotary mode switch
| Switch pin | Wire colour | UHP HECU connection |
|---|
| 1 | Red | 22, ABS_MODE_SW_SENSEEP |
| 2 | White | 23, ABS_MODE_SW_SIG |
| 3 | Black | 29, ABS_MODE_SW_GND |
The manual warns to use the supplied switch. Consult the maker’s diagrams for connector face and orientation, and the separate HECU pinout for the ABS-only unit. Source: AUMOVIO MK 100 UHP technical manual v2.1, pages 17–18 and 22.