Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Datalogging and telematics
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
AiM

MXG 1.3 is a colour motorsport dash with integrated recording. The similarly named Strada display variant must not be assumed to have the same built-in logging. For the range overview see AiM in-car dataloggers.

AiM MXG 1.3
AiM MXG 1.3. Image: AiM, reproduced with permission; AiM product picture library.

Specifications

ItemSpecification
Display7-inch TFT, 800 × 480 pixels
ECU / networksCAN, RS232 or K-Line; three CAN connections
InputsEight configurable analogue/digital inputs; four speed inputs and RPM
Storage / outputs4 GB internal; two digital outputs, 1 A maximum each
Motion / enclosureThree-axis accelerometer and gyro; IP67
GPSGPS09c supplied in listed kits; confirm specific part number

Specifications and kit contents: AiM AiM MXG 1.3 technical documentation. Check hardware generation and exact kit.

Pinout

The MXG 1.3 sheet shows the 37-pin and 22-pin Deutsch male connectors and separate camera Binder connector in external device view. Its 22-pin RS232 labels differ from EVO6.

Main 37-pin

PinFunction
19–15 V power input
2Battery ground
3CAN+ expansion
4Ground
5+Vbattery CAN
6CAN− expansion
7+Vb external
8CAN1+ ECU
9CAN1− ECU
10Ground
11K-Line ECU
12USB D+
13USB D−
14Ground
15RPM
16Ground
17+Vbattery
18Optical lap
19Speed 1
20Ground
21+Vbattery
22Analogue input 1
23Analogue ground
24+Vbattery
25+Vreference
26Analogue input 2
27Analogue ground
28+Vbattery
29+Vreference
30Analogue input 3
31Analogue ground
32+Vbattery
33+Vreference
34Analogue input 4
35Analogue ground
36+Vbattery
37+Vreference

Additional 22-pin

PinFunction
1Analogue input 5
2Analogue ground
3+Vbattery
4+Vreference
5Analogue input 6
6Analogue input 7
7Analogue ground
8+Vbattery
9+Vreference
10Analogue input 8
11Speed 2
12Ground
13+Vbattery
14Speed 3
15Speed 4
16Ground
17CAN2+ ECU
18CAN2− ECU
19Digital output 1
20Digital output 2
21ECU RS232 RX
22ECU RS232 TX

Camera connector, five-pin Binder

PinFunction
1Video input 1
2Ground
3+Vb output camera
4Ground
5Video input 2

Wiring and installation

MXG 1.3 example ECU and power wiring
MXG 1.3 example ECU and power wiring; original Tuning Wiki illustration based on AiM documentation. Schematic diagrams do not show physical connector positions unless explicitly labelled.

AiM lists a main 37-pin harness and optional 22-pin harness. The separate five-pin camera connector is not the CAN expansion port. Check GPS, rear-camera, ECU and sensor lead compatibility and exact kit contents.

Choose the correct model-specific lead and configure the ECU protocol in Race Studio 3. A connector shape alone does not establish vehicle compatibility. Confirm every cavity number, signal level, ground, power source and electrical limit in the linked AiM documentation before wiring; diagrams are from the device view or a conceptual schematic as stated. Secure the loom and make connections with power disconnected.

Software and further reading

Race Studio 3 Analysis example showing suspension traces; actual channels depend on the device and connected sensors
Race Studio 3 Analysis example showing suspension traces; actual channels depend on the device and connected sensors. Image: AiM, reproduced with permission; manufacturer source.

Analysis and download: Race Studio 3 provides setup and PC review of recorded MXG 1.3 data. AiM lists a USB cable in the kit; the recorded channels depend on the configured inputs and connected sources. AiM model guidance. Download the Windows software from AiM Race Studio 3 software downloads. For capabilities and compatibility see AiM data-log analysis software.

Use AiM Race Studio 3 to configure supported devices and analyse recorded sessions. Check the specific ECU protocol and cable before connection; not every source exposes every channel. Manufacturer references: model documentation; product and installation guidance.