Page organisation in this revision
- Page type
- Reference hub
- Subject
- ABS / DSC
- Parent
- AUMOVIO motorsport ABS systems
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- AUMOVIO
Changes from revision 1 to revision 3
Removed text is struck through; added text is highlighted.
The AUMOVIO Engineering Solutions MK 100 UHP is a configurable motorsport ABS kit based on the MK 100 platform. The kit includes the hydraulic/electronic unit, IMU, external brake-pressure sensor, rotary switch and connectors; the product page says wheel-speed sensors are not included. AUMOVIO product information.
Vehicle applications
Manual v2.1 describes race and track vehicles with front/rear split hydraulics and either a tandem master cylinder or two master cylinders with a balance bar. It describes FWD, RWD and AWD vehicle configurations; the product page also describes AWD support as awaiting firmware. Confirm the exact software release and vehicle configuration with AUMOVIO. No particular car model or original-equipment fitment is identified here. MK 100 UHP manual v2.1, page 7; product details.
Hydraulic envelope and HECU identificationManual revision 2.1 specifies maximum hydraulic volume consumption, including calipers and lines, of 34 mm³/bar at the front axle and 15 mm³/bar at the rear. The wheel-locking pressure at which ABS control begins must not exceed 100 bar in that manual’s vehicle environment. The listed HECU reference is 3-75000-013 with a 58-position TE MCon connector and internal front pressure measurement; rear pressure is measured externally. Verify the applicable revision, calibration and complete installation with the supplier: these limits do not establish that a particular vehicle is compatible. AUMOVIO MK 100 UHP manual revision 2.1, page 7.Identification and wiring
This is related through the MK 100 motorsport family to the earlier Continental Engineering Services RSX. Do not assume every RSX and UHP variant, calibration or harness is interchangeable; confirm the part number and current wiring. The MK 100 UHP HECU connector reference is transcribed from the UHP manual itself.
Kit sensor and switch connectorsThe external pressure sensor, IMU and rotary switch connector reference applies to the supplied kit components described in manual v2.1.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: AUMOVIO MK 100 UHP motorsport ABS
The AUMOVIO Engineering Solutions MK 100 UHP is a configurable motorsport ABS kit based on the MK 100 platform. The kit includes the hydraulic/electronic unit, IMU, external brake-pressure sensor, rotary switch and connectors; the product page says wheel-speed sensors are not included. AUMOVIO product information.
Vehicle applications
Manual v2.1 describes race and track vehicles with front/rear split hydraulics and either a tandem master cylinder or two master cylinders with a balance bar. It describes FWD, RWD and AWD vehicle configurations; the product page also describes AWD support as awaiting firmware. Confirm the exact software release and vehicle configuration with AUMOVIO. No particular car model or original-equipment fitment is identified here. MK 100 UHP manual v2.1, page 7; product details.
Identification and wiring
This is related through the MK 100 motorsport family to the earlier Continental Engineering Services RSX. Do not assume every RSX and UHP variant, calibration or harness is interchangeable; confirm the part number and current wiring. The MK 100 UHP HECU connector reference is transcribed from the UHP manual itself.
Revision 3: AUMOVIO MK 100 UHP motorsport ABS
The AUMOVIO Engineering Solutions MK 100 UHP is a configurable motorsport ABS kit based on the MK 100 platform. The kit includes the hydraulic/electronic unit, IMU, external brake-pressure sensor, rotary switch and connectors; the product page says wheel-speed sensors are not included. AUMOVIO product information.
Vehicle applications
Manual v2.1 describes race and track vehicles with front/rear split hydraulics and either a tandem master cylinder or two master cylinders with a balance bar. It describes FWD, RWD and AWD vehicle configurations; the product page also describes AWD support as awaiting firmware. Confirm the exact software release and vehicle configuration with AUMOVIO. No particular car model or original-equipment fitment is identified here. MK 100 UHP manual v2.1, page 7; product details.
Hydraulic envelope and HECU identification
Manual revision 2.1 specifies maximum hydraulic volume consumption, including calipers and lines, of 34 mm³/bar at the front axle and 15 mm³/bar at the rear. The wheel-locking pressure at which ABS control begins must not exceed 100 bar in that manual’s vehicle environment. The listed HECU reference is 3-75000-013 with a 58-position TE MCon connector and internal front pressure measurement; rear pressure is measured externally. Verify the applicable revision, calibration and complete installation with the supplier: these limits do not establish that a particular vehicle is compatible. AUMOVIO MK 100 UHP manual revision 2.1, page 7.
Identification and wiring
This is related through the MK 100 motorsport family to the earlier Continental Engineering Services RSX. Do not assume every RSX and UHP variant, calibration or harness is interchangeable; confirm the part number and current wiring. The MK 100 UHP HECU connector reference is transcribed from the UHP manual itself.
Kit sensor and switch connectors
The external pressure sensor, IMU and rotary switch connector reference applies to the supplied kit components described in manual v2.1.