Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Chevrolet, GMC, Holden

These examples concern HP Tuners work on 2.8-litre diesel Colorado pickups, with separately identified Holden owner questions and a 2016 Chevrolet/GMC North American factory example. They do not establish that calibrations, controllers, sensors or transmissions are interchangeable across regions or model years.

Vehicle, engine and gearbox identification

GM's 2016 Colorado and Canyon diesel technical bulletin PI1539 identifies the North American crew-cab diesel as a 2.8-litre, direct-injection, turbocharged DOHC four-cylinder, RPO LWN, paired with the six-speed Hydra-Matic 6L50 automatic, RPO MYB. The described converter includes a centrifugal pendulum vibration absorber. This factory US/Canada specification does not establish the engine or transmission in an Australian Holden or a modified truck.

HP Tuners' GM application list separately lists Chevrolet Colorado diesel and Holden Colorado 2.8 diesel applications. A 2014 Holden owner in the discussion below identifies their own ECU as E98; that report is not proof every Colorado 2.8 uses E98. Identify PCM hardware, calibration, model year, market and exact transmission and check current device, operating-system and licensing requirements. Engine listing alone does not establish TCM access.

MAF value flattening while boost falls

In an Australian Colorado 2.8 diesel HP Tuners discussion, an owner said airflow as logged with a Snap-on scanner stopped increasing at approximately 217 g/s while boost fell at higher engine speed. They used HP Tuners to edit, noted that another older Colorado used a voltage-based MAF table, and later said that an underlined frequency-axis heading in their own file was editable. The ECU, model year, actual sensor signal and outcome were not verified in the accessible thread. The tutor explicitly said they had not tuned this diesel. The observation is not proof of a universal 217 g/s limit, a sensor fault or a current VCM Scanner limitation.

When assessing a flat trace, compare the raw signal or frequency and scaled mass-airflow channels where available, rpm, requested and measured pressure, barometric pressure, temperature and boost-control command on the same timeline. Establish if the raw signal continues to move, whether the scanner or displayed channel saturates, and whether a calibration or sensor range has been reached. Check wiring, sensors, intake and charge piping, actuator and current service information. Do not assume the same PID, transfer curve or frequency/voltage axis across ECUs. If an axis is editable, extending it alone does not establish correct airflow values; verify the definition, physical sensor range and resulting calibration using an appropriate method. HP Tuners table editor and axis functions.

Fuel quantity, torque and rail pressure are distinct

In another Holden Colorado 2.8 discussion, an HP Tuners user asked why an indicated fuel quantity remained below the end of a base-fuelling table after changing torque limits. A respondent offered fuel-supply capacity as one possible explanation, without a confirmed diagnosis. The maximum axis entry is not necessarily an ECU command or a target to reach, and the reported figures are not safe values for another truck.

Record whether a quantity is requested, calculated or measured, its units and the conditions for the active mode. Where supported, compare desired and actual rail pressure, commanded fuel quantity, load, airflow, manifold pressure and temperature, together with faults and fuel-system condition. Fuel quantity, timing, rail pressure, available air and temperature interact; an isolated high value or higher pressure request does not verify adequate fuel delivery or a safe calibration. Follow the correct high-pressure diesel diagnostic procedure and equipment requirements.

Turbo hardware changes are not a selector-only job

In a separate 2014 Holden RG E98 case, an owner planning a variable-geometry to wastegated turbo swap asked whether a VCM Editor forced-induction selection was sufficient and what to do with the original actuator. The responder explicitly had not tested that setup; the accessible thread contains no validated conversion result, and attachments were not reviewed. Do not treat its suggested selector or actuator approach as a proven procedure. Confirm the exact hardware, actuator and control system, ECU definition, pressure sensor scaling and supplier instructions; check operation and maintain required emissions and protective functions.

6L50 transmission logging

GM's 2016 bulletin describes an internal transmission control module and a hydraulically applied converter clutch controlled by a pressure-control solenoid. Where available for the actual truck and scanner, compare requested and actual gear, vehicle and engine speed, throttle/load, transmission temperature and converter clutch command and slip. A shift request or converter command alone does not prove mechanical application; check fluid, diagnostic codes, wiring and hydraulic/mechanical condition before changing shift or torque controls. The North American 6L50 description should not be assumed for the Holden discussion vehicles. GM PI1539, transmission description.

Record DTCs before reading: HP Tuners warns that reading can clear them. Save the vehicle's own supported original calibration, note sensor and mechanical modifications, and capture a baseline; make a documented change only when its function is understood, then verify with a fresh log. HP Tuners: getting started with VCM Editor. See also VCM Scanner and MPVI4.