This guide concerns HP Tuners on selected Jeep Wrangler JL and Gladiator JT 3.6-litre Pentastar vehicles, with a 2024 Wrangler and 850RE eight-speed example. Check the vehicle, engine, PCM, transmission and calibration independently; the model name alone does not establish support.
Engine and gearbox identification
Jeep's 2024 Wrangler specifications describe a 3,604 cc 60-degree Pentastar V6 with chain-driven double overhead cams, 24 valves, sequential multiport injection, 285 hp and 260 lb-ft in the stated US specification. The 3.6 with engine stop-start was offered with a D478 six-speed manual or 850RE eight-speed automatic; equipment varies with trim and market. An automatic shift complaint and a manual-transmission hesitation require different investigation. Jeep: 2024 Wrangler specifications.
GPEC2A versus GPEC5 and access
HP Tuners lists 2018–23 Wrangler JL 3.6 with GPEC2A, and 2022–25 Wrangler 3.6 with GPEC5, as separate entries. Its GPEC5 service page also lists 2021–25 Gladiator 3.6. Overlapping years do not identify the fitted controller: verify the PCM and exact vehicle with HP Tuners. The service page specifies a send-in GPEC5 upgrade, 2018+ Smart Access Cable, MPVI3 or MPVI4, VCM Suite beta and separate PCM licensing. It says programming is not included in the upgrade. Its ZF8 TCM licensing is separate; verify the individual module, current software and prices before starting. Do not assume the same requirements or support for every Jeep or the 392 V8. HP Tuners: Stellantis vehicle list; GPEC5 PCM service.
Before a supported module read or tune, record diagnostic trouble codes, identify hardware and calibration, record fuel and modifications, and save the vehicle's own original read. HP Tuners warns that a vehicle read clears DTCs. A replacement module or operating-system change can have separate licensing or programming implications. HP Tuners: getting started; HP Tuners: licensing.
Low-speed hesitation: separate symptoms from causes
In a 2026 Wrangler forum discussion, the owner of a 2025 JL 3.6 described low-rpm hesitation and planned to investigate using HP Tuners. The poster suggested interactions involving cam timing, EGR and spark but explicitly presented them as hypotheses before testing. The thread alone does not establish a universal cause or justify copying a cam, spark or emissions-related setting.
In a separate review, a 2024 JLUR-X owner with 40-inch tyres and 5.38 axle gears reported improved 3–4 hesitation and different eighth-gear behaviour after both engine and transmission tuning. Multiple factors changed and the report is subjective; it does not isolate a faulty table, prove a cause, or establish the result for another vehicle. The same owner subsequently questioned whether the available fan settings were actually effective. Confirm commanded and actual behaviour on the specific vehicle rather than assuming a displayed table controls the expected function.
VCM Scanner investigation
- Record the exact event: engine and transmission warm-up, gear or manual mode, approximate road speed and rpm, pedal position, hill, trailer, fuel and whether it occurs during a shift or while the gear is held. Check tyre size and axle ratio against the vehicle's configuration and verify road speed using suitable independent measurement.
- Configure a supported VCM Scanner profile and record engine speed, vehicle speed, pedal and throttle, engine load or MAP, spark advance, knock-related channels, commanded and actual cam position, and fuel trims where available. For the automatic add requested and actual gear, transmission temperature and converter-clutch command or slip if exposed. Available names, definitions and update rates depend on the controller; a layout does not automatically add channels. HP Tuners: scanner configuration; scanner layouts and channels.
- Compare repeatable events at similar temperatures and load. A dip in rpm or change in spark around a shift is not by itself proof of knock, a cam fault or transmission damage. Inspect stored faults and mechanical, electrical and fuel-system conditions before changing calibration. When comparing a subsequent tune, document which modules and settings changed and obtain a fresh log; do not treat higher line pressure or reduced torque management as a universal remedy.
Check manufacturer service information
Stellantis TSB 21-020-25 concerns certain 2024 JL Wrangler 3.6 ERC vehicles with 850RE DFT where the MIL and P1DB7-00 torque-converter clutch performance code are present; it describes a TCM software update. It is not a diagnosis or fix for every hesitation complaint. TSB 18-050-24 Rev. B addresses specified 2024 3.6 ERC PCM conditions, with model build-date and fault-code restrictions. Check current revisions and VIN eligibility and follow the manufacturer's diagnostic procedure. The service-bulletin reflash is an OEM service procedure, not an HP Tuners calibration step.
Related pages
Jeep Wrangler generations and engines; HP Tuners VCM Scanner; HP Tuners MPVI4.