Removed text is struck through; added text is highlighted.
A diesel particulate filter (DPF) differential pressure sensor reports the pressure difference between specified points in the exhaust. The engine control unit (ECU) uses this information with other inputs to monitor filter flow resistance and support soot-load estimation and regeneration. A high or low reading is evidence to investigate, not a direct weighing of soot or proof that a filter or sensor has failed.
For the whole system see petrol and diesel emissions, diesel particulate filters, DPF load models, DPF regeneration, particulate filter faults and exhaust temperature sensors.
Pressure difference and the sampling points
In a common two-line system the sensor compares pressure at an inlet-side tapping with pressure at an outlet-side tapping. The reported differential is normally inlet pressure minus outlet pressure. Exhaust passes through the filter walls; flow resistance creates a difference between those points. Pipes and hoses transmit pressure to a sensor mounted away from the hottest exhaust components. HELLA: DPF and differential pressure.
The exact tapping points and components between them depend on the exhaust layout. Do not assume a reading describes only a bare filter brick, or that every vehicle has two external hoses: some pressure-sensing arrangements use a pressure point and an atmospheric reference instead of directly measuring the difference across the filter. Continental documents a single-port exhaust gauge-pressure sensor for measurement before or after the DPF; it is not automatically a direct across-filter measurement. Continental sensor product booklet. A pressure sensor can also be used in a low-pressure EGR circuit. Identify the exact physical component and diagram before disconnecting anything. Bosch: differential pressure sensors and applications.
Differential pressure compares two points; gauge pressure compares a point with atmospheric pressure; absolute pressure uses a vacuum reference. They cannot be interchanged simply by relabelling a scan-tool value. For pressure differences, 1 kPa = 10 mbar = 1,000 Pa. A displayed minus sign, unit, sensor label and reference are part of the reading. Convert units before comparing values and check whether the tool reports a measured pressure, an inferred pressure or another parameter.
How the sensor and ECU use the signal
Bosch describes a differential-pressure device with a piezoresistive sensing element: a pressure-induced change in the element is processed into an electrical signal for the control unit. Actual circuit, pressure range, connector, transfer curve and offset depend on the part. A typical analogue circuit may use a supply, ground and signal, but the correct identification and measurement method come from the vehicle wiring diagram and service information; do not assume wire colour, pin position, voltage range or a calibration from another sensor. Bosch: sensor construction.
The ECU interprets pressure alongside exhaust flow, temperature, operating state and its calibration. Some strategies calculate engine-out soot and soot oxidation and compare that model with pressure; other strategies use different models or estimates. A scan-tool soot or ash mass is usually a calculated value, not something the sensor weighs. See DPF load models and the HELLA aftertreatment overview.
What makes a reading rise or fall?
InfluenceWhat it means for diagnosis
Exhaust flowPressure drop normally changes with flow. Compare measured values only at the manufacturer's specified engine conditions and flow, not against a single universal idle or road-speed figure.
Temperature and gas propertiesGas temperature and the control model influence the relationship between flow and pressure. A cold and a hot reading are not automatically comparable.
Soot loadingAccumulated soot can increase restriction. A successful regeneration oxidises soot under suitable conditions; a reading can change as the filter and operating state change.
Ash and permanent depositsNon-combustible ash can remain after soot regeneration and contribute to restriction. Pressure alone cannot reliably separate soot and ash mass. Follow the manufacturer's service assessment.
Damaged filter or leakA cracked substrate or exhaust leak can affect pressure and allow an unexpectedly low value; low restriction alone does not prove effective filtration.
Sensor, ports and hosesLeaks, restrictions, melted sections, condensate, swapped connections, wiring or sensor offset can distort the measured value independently of filter condition.
Pressure response is a system measurement. Soot, ash, exhaust flow, temperature and the actual sensor connection must be assessed together. A low static pressure does not prove the filter is intact or clean; a high value does not by itself prove the filter needs replacement. See soot and ash and particulate filter faults.
Pressure lines and sensor faults
Pressure pipes and hoses can crack, detach, chafe, melt, block with soot or collect condensate. A line restriction can delay or distort a response; a leak can cause an implausible signal. The result depends on which line and port are affected. Check the pressure take-offs as well as the visible hose. Before removing a line, record its routing and connections; use the correct heat-resistant specified replacements and clamps and route them away from heat and moving parts. Do not reverse inlet and outlet connections or blow compressed air through an attached sensor.
Electrical connectors can corrode, wires can fail from vibration or heat, and the sensor itself can drift or fail. A documented Mercedes-Benz service case identified hose and electrical issues among possible causes of sensor faults, while a HELLA Dacia Dokker example shows a cracked hose affecting plausibility. These are vehicle-specific examples. Mercedes-Benz service information.
Common problems: symptoms and checks
FindingPossible causes and first checks
DPF warning or regeneration faultsPressure-sensor and hose faults can affect the load calculation, but a restricted filter or an engine problem can cause similar symptoms. Inspect ports, hoses and wiring, then compare pressure and regeneration data under specified conditions.
Pressure value changes slowly or appears implausibleA restricted, split, melted or disconnected line, blocked tapping or sensor fault can distort the result. Check both lines and their correct routing where fitted; use the applicable diagram and safe cooled-exhaust procedure.
High pressure or excessive soot-load estimateSoot or ash restriction, a pressure-line problem or sensor offset are possible. Consider exhaust flow and temperature and use the manufacturer's test; a high reading alone cannot establish soot mass or condemn the filter.
Low or unexpected pressureA pressure or exhaust leak, a damaged filter, an incorrect sensor or signal issue can affect the reading. A low pressure reading does not prove that the filter is intact or filtering properly.
These findings require system-specific checks. HELLA: Dacia hose fault example; HELLA: aftertreatment diagnostics.
Fault codes and symptoms
Possible symptoms include a warning lamp, restricted power, regeneration problems, increased fuel consumption or a DPF warning. The same symptom can come from several components. Delphi lists P2452 for a pressure-sensor circuit, P2453 for circuit range/performance and P2454/P2455 for circuit low/high as examples. Code text, suffix and monitor conditions vary by vehicle; P2463 can relate to soot accumulation in a documented Chrysler application. An exhaust leak or defective hose can contribute to pressure-related codes. Delphi: differential-pressure sensor faults; FCA bulletin 18-054-15.
Workshop diagnosis
Identify the system. Record the vehicle, engine, sensor location, fault codes, freeze-frame data, actual part number and relevant technical bulletins. Obtain the exhaust diagram and the diagnostic procedure for that engine and software.
Check operating state. Record temperatures, engine speed and load, calculated or measured exhaust flow where available, the regeneration state and the unit used for the pressure. Compare like conditions and use the manufacturer's test limits.
Inspect safely. Once the exhaust has cooled as required, inspect the sensor, connector, wiring, pressure ports, metal pipes, flexible hoses, clamps and routing. Look for cracks, leaks, chafing, crushed sections, condensation and restricted take-offs. Check for exhaust leaks and other aftertreatment faults.
Check the zero or offset where specified. A no-flow key-on, engine-off reading can be a useful plausibility check on an applicable system, but its permitted offset, settling time and conditions come from the manufacturer. A value near zero does not prove accurate readings throughout the range, and a stored offset is not a universal fault. Do not open hot lines or infer a universal specification.
Test the sensor and circuit. Follow the appropriate wiring diagram and approved test equipment for supply, ground and signal. If directed, compare the sensor's pressure response against a suitable calibrated pressure source and gauge over the specified range, with the correct port and pressure limits. Never compare volts numerically with a pressure value or apply arbitrary pressure to an unknown sensor.
Assess filter and upstream causes. Investigate soot loading, ash, exhaust leaks, airflow, temperature and combustion or injection faults using the model-specific procedure. A pressure reading alone cannot distinguish a restricted filter from blocked pipes or an offset sensor.
Repair and verify. Restore the correct hoses and connections, rectify the cause, then carry out the manufacturer's required adaptation or reset and confirm readings and fault status under specified conditions. Clear fault codes when appropriate, and record results.
Do not run a forced regeneration solely to clear a pressure fault. Ensure the underlying cause and the filter condition have been assessed and all manufacturer preconditions are satisfied. Exhaust parts and regeneration can reach hazardous temperatures: use the vehicle-specific process, suitable exhaust extraction and fire precautions. HSE: vehicle exhaust emissions.
Replacement, offset and learned values
Select the correct sensor for the actual vehicle, engine and system. Similar housings, connectors and number of hose stubs do not guarantee equal pressure range, offset, transfer curve, installation or compatibility. Some vehicles require a sensor offset adaptation after a sensor or hose repair; others use a different procedure. For example, FCA bulletin 18-054-15 specifies an offset reset on its listed 2010–2015 2.8-litre diesel application. That instruction is not authority to reset the filter soot or ash values on every vehicle. FCA service bulletin.
Distinguish a pressure-sensor zero or offset from a learned DPF soot or ash value. Reset or replacement functions can have different names and effects in different tools. Use only the exact function required for the repair; resetting an estimate does not clean a filter or remove ash. If the filter was cleaned or replaced, follow the applicable manufacturer procedure for that work separately.
Examples of pressure sensors and applications
The following are documented examples, not an exhaustive application catalogue. A bulletin describes only the vehicles, market, dates and conditions it lists; parts can be superseded or specified as an assembly with different hoses. Confirm the current part, engine, exhaust arrangement, emissions equipment and VIN with the manufacturer's parts information before ordering. A DPF pressure sensor is not necessarily the similarly named EGR pressure sensor or a particulate-matter sensor.
Published sensor referenceDocumented example and limitsSource and identification notes
Volkswagen Group 059 906 051 A; HELLA 6PP 009 409-231HELLA lists VW Touareg 7P5 diesel TDI, model years 2010–2014, in a regeneration fault case.HELLA case. The case lists these two references; confirm the actual vehicle and current parts listing.
Audi 059 906 051 AAudi campaign 23L2 covers selected 2009–2012 Audi Q7 3.0 TDI vehicles in the USA and Canada.Audi campaign specifies the reference and shows two particulate-filter hoses. Campaign eligibility depends on VIN; it does not describe every Q7 worldwide.
FCA 56044587ABFCA bulletin 18-054-15 specifies 2010–2015 Chrysler Town & Country, international market, with the ENS 2.8-litre diesel.FCA service bulletin lists the sensor, connector kit and a procedure for its stated fault conditions.
Ford HC3Z-9J460-D2017–2018 F-Super Duty 6.7 L, built on or before 18 April 2018: pickup with 142-, 148- or 164-inch wheelbase.Ford bulletin 18-2371. These are distinct service references for the stated US-market bulletin conditions, not general cross-references.
Ford HC3Z-9J460-FSame bulletin: pickup with 160- or 176-inch wheelbase.
Ford HC3Z-9J460-ESame bulletin: chassis cab.
Land Rover LR0696602016 Range Rover (LG) 3.0 TDV6 Gen 2 in the North American bulletin's VIN range, single-speed transfer case.JLR bulletin LTB01192NAS1 gives market and VIN restrictions and also lists specified Range Rover Sport vehicles.
Land Rover LR069684Same bulletin and market, twin-speed transfer case.
Cummins 5492073 / Emission Solutions A061B903Selected X15 CM2350 X114B, X116B and X123B aftertreatment configurations.Cummins TSB200080 specifies different service kits by configuration; the sensor's larger ports require the corresponding larger tubes.
PACCAR 1818119Kenworth Canadian-registered chassis notice identifies the DPF differential-pressure sensor in selected 2017 MX-13 engines.PACCAR/Kenworth E273 notice lists it separately from the PM sensor; scope is the notice's identified chassis.
These examples show why matching a plug or a numerical part-family prefix is insufficient. Check whether the listed reference denotes a bare sensor, a complete sensor-and-line assembly, or a kit; compare the correct pressure connections and any required adaptation in current vehicle documentation.
Testing and UK MOT
A differential-pressure sensor monitors a pressure difference or a pressure used in a particular model; it is not a smoke meter, a particle-number counter or a NOx sensor. A low pressure reading does not demonstrate particle-filter efficiency. The DVSA MOT inspection manual, section 8 specifies applicable visible emissions-equipment, malfunction-indicator and smoke checks and exemptions; do not assume a routine MOT includes a dedicated differential-pressure accuracy test. See emissions testing equipment.
Sources and related reading
Bosch Mobility: differential pressure sensor — operating principle and DPF versus low-pressure EGR applications.
HELLA: exhaust aftertreatment diagnostics — DPF and pressure monitoring.
Delphi: DPF differential pressure sensor — hose defects and example codes. Use vehicle-specific electrical and pressure specifications.
FCA bulletin 18-054-15 — one vehicle-specific sensor and offset service procedure.
DVSA MOT manual, section 8 and HSE exhaust guidance.
Open each version to inspect formatting, tables and photographs.
Revision 2: DPF differential pressure sensors: operation, applications and diagnosis
A diesel particulate filter (DPF) differential pressure sensor reports the pressure difference between specified points in the exhaust. The engine control unit (ECU) uses this information with other inputs to monitor filter flow resistance and support soot-load estimation and regeneration. A high or low reading is evidence to investigate, not a direct weighing of soot or proof that a filter or sensor has failed.
For the whole system see petrol and diesel emissions, diesel particulate filters, DPF load models, DPF regeneration, particulate filter faults and exhaust temperature sensors.
Pressure difference and the sampling points
In a common two-line system the sensor compares pressure at an inlet-side tapping with pressure at an outlet-side tapping. The reported differential is normally inlet pressure minus outlet pressure. Exhaust passes through the filter walls; flow resistance creates a difference between those points. Pipes and hoses transmit pressure to a sensor mounted away from the hottest exhaust components. HELLA: DPF and differential pressure.
The exact tapping points and components between them depend on the exhaust layout. Do not assume a reading describes only a bare filter brick, or that every vehicle has two external hoses: some pressure-sensing arrangements use a pressure point and an atmospheric reference instead of directly measuring the difference across the filter. Continental documents a single-port exhaust gauge-pressure sensor for measurement before or after the DPF; it is not automatically a direct across-filter measurement. Continental sensor product booklet. A pressure sensor can also be used in a low-pressure EGR circuit. Identify the exact physical component and diagram before disconnecting anything. Bosch: differential pressure sensors and applications.
Differential pressure compares two points; gauge pressure compares a point with atmospheric pressure; absolute pressure uses a vacuum reference. They cannot be interchanged simply by relabelling a scan-tool value. For pressure differences, 1 kPa = 10 mbar = 1,000 Pa. A displayed minus sign, unit, sensor label and reference are part of the reading. Convert units before comparing values and check whether the tool reports a measured pressure, an inferred pressure or another parameter.
How the sensor and ECU use the signal
Bosch describes a differential-pressure device with a piezoresistive sensing element: a pressure-induced change in the element is processed into an electrical signal for the control unit. Actual circuit, pressure range, connector, transfer curve and offset depend on the part. A typical analogue circuit may use a supply, ground and signal, but the correct identification and measurement method come from the vehicle wiring diagram and service information; do not assume wire colour, pin position, voltage range or a calibration from another sensor. Bosch: sensor construction.
The ECU interprets pressure alongside exhaust flow, temperature, operating state and its calibration. Some strategies calculate engine-out soot and soot oxidation and compare that model with pressure; other strategies use different models or estimates. A scan-tool soot or ash mass is usually a calculated value, not something the sensor weighs. See DPF load models and the HELLA aftertreatment overview.
What makes a reading rise or fall?
| Influence | What it means for diagnosis |
| Exhaust flow | Pressure drop normally changes with flow. Compare measured values only at the manufacturer's specified engine conditions and flow, not against a single universal idle or road-speed figure. |
| Temperature and gas properties | Gas temperature and the control model influence the relationship between flow and pressure. A cold and a hot reading are not automatically comparable. |
| Soot loading | Accumulated soot can increase restriction. A successful regeneration oxidises soot under suitable conditions; a reading can change as the filter and operating state change. |
| Ash and permanent deposits | Non-combustible ash can remain after soot regeneration and contribute to restriction. Pressure alone cannot reliably separate soot and ash mass. Follow the manufacturer's service assessment. |
| Damaged filter or leak | A cracked substrate or exhaust leak can affect pressure and allow an unexpectedly low value; low restriction alone does not prove effective filtration. |
| Sensor, ports and hoses | Leaks, restrictions, melted sections, condensate, swapped connections, wiring or sensor offset can distort the measured value independently of filter condition. |
Pressure response is a system measurement. Soot, ash, exhaust flow, temperature and the actual sensor connection must be assessed together. A low static pressure does not prove the filter is intact or clean; a high value does not by itself prove the filter needs replacement. See soot and ash and particulate filter faults.
Pressure lines and sensor faults
Pressure pipes and hoses can crack, detach, chafe, melt, block with soot or collect condensate. A line restriction can delay or distort a response; a leak can cause an implausible signal. The result depends on which line and port are affected. Check the pressure take-offs as well as the visible hose. Before removing a line, record its routing and connections; use the correct heat-resistant specified replacements and clamps and route them away from heat and moving parts. Do not reverse inlet and outlet connections or blow compressed air through an attached sensor.
Electrical connectors can corrode, wires can fail from vibration or heat, and the sensor itself can drift or fail. A documented Mercedes-Benz service case identified hose and electrical issues among possible causes of sensor faults, while a HELLA Dacia Dokker example shows a cracked hose affecting plausibility. These are vehicle-specific examples. Mercedes-Benz service information.
Common problems: symptoms and checks
| Finding | Possible causes and first checks |
| DPF warning or regeneration faults | Pressure-sensor and hose faults can affect the load calculation, but a restricted filter or an engine problem can cause similar symptoms. Inspect ports, hoses and wiring, then compare pressure and regeneration data under specified conditions. |
| Pressure value changes slowly or appears implausible | A restricted, split, melted or disconnected line, blocked tapping or sensor fault can distort the result. Check both lines and their correct routing where fitted; use the applicable diagram and safe cooled-exhaust procedure. |
| High pressure or excessive soot-load estimate | Soot or ash restriction, a pressure-line problem or sensor offset are possible. Consider exhaust flow and temperature and use the manufacturer's test; a high reading alone cannot establish soot mass or condemn the filter. |
| Low or unexpected pressure | A pressure or exhaust leak, a damaged filter, an incorrect sensor or signal issue can affect the reading. A low pressure reading does not prove that the filter is intact or filtering properly. |
These findings require system-specific checks. HELLA: Dacia hose fault example; HELLA: aftertreatment diagnostics.
Fault codes and symptoms
Possible symptoms include a warning lamp, restricted power, regeneration problems, increased fuel consumption or a DPF warning. The same symptom can come from several components. Delphi lists P2452 for a pressure-sensor circuit, P2453 for circuit range/performance and P2454/P2455 for circuit low/high as examples. Code text, suffix and monitor conditions vary by vehicle; P2463 can relate to soot accumulation in a documented Chrysler application. An exhaust leak or defective hose can contribute to pressure-related codes. Delphi: differential-pressure sensor faults; FCA bulletin 18-054-15.
Workshop diagnosis
- Identify the system. Record the vehicle, engine, sensor location, fault codes, freeze-frame data, actual part number and relevant technical bulletins. Obtain the exhaust diagram and the diagnostic procedure for that engine and software.
- Check operating state. Record temperatures, engine speed and load, calculated or measured exhaust flow where available, the regeneration state and the unit used for the pressure. Compare like conditions and use the manufacturer's test limits.
- Inspect safely. Once the exhaust has cooled as required, inspect the sensor, connector, wiring, pressure ports, metal pipes, flexible hoses, clamps and routing. Look for cracks, leaks, chafing, crushed sections, condensation and restricted take-offs. Check for exhaust leaks and other aftertreatment faults.
- Check the zero or offset where specified. A no-flow key-on, engine-off reading can be a useful plausibility check on an applicable system, but its permitted offset, settling time and conditions come from the manufacturer. A value near zero does not prove accurate readings throughout the range, and a stored offset is not a universal fault. Do not open hot lines or infer a universal specification.
- Test the sensor and circuit. Follow the appropriate wiring diagram and approved test equipment for supply, ground and signal. If directed, compare the sensor's pressure response against a suitable calibrated pressure source and gauge over the specified range, with the correct port and pressure limits. Never compare volts numerically with a pressure value or apply arbitrary pressure to an unknown sensor.
- Assess filter and upstream causes. Investigate soot loading, ash, exhaust leaks, airflow, temperature and combustion or injection faults using the model-specific procedure. A pressure reading alone cannot distinguish a restricted filter from blocked pipes or an offset sensor.
- Repair and verify. Restore the correct hoses and connections, rectify the cause, then carry out the manufacturer's required adaptation or reset and confirm readings and fault status under specified conditions. Clear fault codes when appropriate, and record results.
Do not run a forced regeneration solely to clear a pressure fault. Ensure the underlying cause and the filter condition have been assessed and all manufacturer preconditions are satisfied. Exhaust parts and regeneration can reach hazardous temperatures: use the vehicle-specific process, suitable exhaust extraction and fire precautions. HSE: vehicle exhaust emissions.
Replacement, offset and learned values
Select the correct sensor for the actual vehicle, engine and system. Similar housings, connectors and number of hose stubs do not guarantee equal pressure range, offset, transfer curve, installation or compatibility. Some vehicles require a sensor offset adaptation after a sensor or hose repair; others use a different procedure. For example, FCA bulletin 18-054-15 specifies an offset reset on its listed 2010–2015 2.8-litre diesel application. That instruction is not authority to reset the filter soot or ash values on every vehicle. FCA service bulletin.
Distinguish a pressure-sensor zero or offset from a learned DPF soot or ash value. Reset or replacement functions can have different names and effects in different tools. Use only the exact function required for the repair; resetting an estimate does not clean a filter or remove ash. If the filter was cleaned or replaced, follow the applicable manufacturer procedure for that work separately.
Examples of pressure sensors and applications
The following are documented examples, not an exhaustive application catalogue. A bulletin describes only the vehicles, market, dates and conditions it lists; parts can be superseded or specified as an assembly with different hoses. Confirm the current part, engine, exhaust arrangement, emissions equipment and VIN with the manufacturer's parts information before ordering. A DPF pressure sensor is not necessarily the similarly named EGR pressure sensor or a particulate-matter sensor.
| Published sensor reference | Documented example and limits | Source and identification notes |
| Volkswagen Group 059 906 051 A; HELLA 6PP 009 409-231 | HELLA lists VW Touareg 7P5 diesel TDI, model years 2010–2014, in a regeneration fault case. | HELLA case. The case lists these two references; confirm the actual vehicle and current parts listing. |
| Audi 059 906 051 A | Audi campaign 23L2 covers selected 2009–2012 Audi Q7 3.0 TDI vehicles in the USA and Canada. | Audi campaign specifies the reference and shows two particulate-filter hoses. Campaign eligibility depends on VIN; it does not describe every Q7 worldwide. |
| FCA 56044587AB | FCA bulletin 18-054-15 specifies 2010–2015 Chrysler Town & Country, international market, with the ENS 2.8-litre diesel. | FCA service bulletin lists the sensor, connector kit and a procedure for its stated fault conditions. |
| Ford HC3Z-9J460-D | 2017–2018 F-Super Duty 6.7 L, built on or before 18 April 2018: pickup with 142-, 148- or 164-inch wheelbase. | Ford bulletin 18-2371. These are distinct service references for the stated US-market bulletin conditions, not general cross-references. |
| Ford HC3Z-9J460-F | Same bulletin: pickup with 160- or 176-inch wheelbase. |
| Ford HC3Z-9J460-E | Same bulletin: chassis cab. |
| Land Rover LR069660 | 2016 Range Rover (LG) 3.0 TDV6 Gen 2 in the North American bulletin's VIN range, single-speed transfer case. | JLR bulletin LTB01192NAS1 gives market and VIN restrictions and also lists specified Range Rover Sport vehicles. |
| Land Rover LR069684 | Same bulletin and market, twin-speed transfer case. |
| Cummins 5492073 / Emission Solutions A061B903 | Selected X15 CM2350 X114B, X116B and X123B aftertreatment configurations. | Cummins TSB200080 specifies different service kits by configuration; the sensor's larger ports require the corresponding larger tubes. |
| PACCAR 1818119 | Kenworth Canadian-registered chassis notice identifies the DPF differential-pressure sensor in selected 2017 MX-13 engines. | PACCAR/Kenworth E273 notice lists it separately from the PM sensor; scope is the notice's identified chassis. |
These examples show why matching a plug or a numerical part-family prefix is insufficient. Check whether the listed reference denotes a bare sensor, a complete sensor-and-line assembly, or a kit; compare the correct pressure connections and any required adaptation in current vehicle documentation.
Testing and UK MOT
A differential-pressure sensor monitors a pressure difference or a pressure used in a particular model; it is not a smoke meter, a particle-number counter or a NOx sensor. A low pressure reading does not demonstrate particle-filter efficiency. The DVSA MOT inspection manual, section 8 specifies applicable visible emissions-equipment, malfunction-indicator and smoke checks and exemptions; do not assume a routine MOT includes a dedicated differential-pressure accuracy test. See emissions testing equipment.
Sources and related reading
Revision 2: DPF differential pressure sensors: operation, applications and diagnosis
A diesel particulate filter (DPF) differential pressure sensor reports the pressure difference between specified points in the exhaust. The engine control unit (ECU) uses this information with other inputs to monitor filter flow resistance and support soot-load estimation and regeneration. A high or low reading is evidence to investigate, not a direct weighing of soot or proof that a filter or sensor has failed.
For the whole system see petrol and diesel emissions, diesel particulate filters, DPF load models, DPF regeneration, particulate filter faults and exhaust temperature sensors.
Pressure difference and the sampling points
In a common two-line system the sensor compares pressure at an inlet-side tapping with pressure at an outlet-side tapping. The reported differential is normally inlet pressure minus outlet pressure. Exhaust passes through the filter walls; flow resistance creates a difference between those points. Pipes and hoses transmit pressure to a sensor mounted away from the hottest exhaust components. HELLA: DPF and differential pressure.
The exact tapping points and components between them depend on the exhaust layout. Do not assume a reading describes only a bare filter brick, or that every vehicle has two external hoses: some pressure-sensing arrangements use a pressure point and an atmospheric reference instead of directly measuring the difference across the filter. Continental documents a single-port exhaust gauge-pressure sensor for measurement before or after the DPF; it is not automatically a direct across-filter measurement. Continental sensor product booklet. A pressure sensor can also be used in a low-pressure EGR circuit. Identify the exact physical component and diagram before disconnecting anything. Bosch: differential pressure sensors and applications.
Differential pressure compares two points; gauge pressure compares a point with atmospheric pressure; absolute pressure uses a vacuum reference. They cannot be interchanged simply by relabelling a scan-tool value. For pressure differences, 1 kPa = 10 mbar = 1,000 Pa. A displayed minus sign, unit, sensor label and reference are part of the reading. Convert units before comparing values and check whether the tool reports a measured pressure, an inferred pressure or another parameter.
How the sensor and ECU use the signal
Bosch describes a differential-pressure device with a piezoresistive sensing element: a pressure-induced change in the element is processed into an electrical signal for the control unit. Actual circuit, pressure range, connector, transfer curve and offset depend on the part. A typical analogue circuit may use a supply, ground and signal, but the correct identification and measurement method come from the vehicle wiring diagram and service information; do not assume wire colour, pin position, voltage range or a calibration from another sensor. Bosch: sensor construction.
The ECU interprets pressure alongside exhaust flow, temperature, operating state and its calibration. Some strategies calculate engine-out soot and soot oxidation and compare that model with pressure; other strategies use different models or estimates. A scan-tool soot or ash mass is usually a calculated value, not something the sensor weighs. See DPF load models and the HELLA aftertreatment overview.
What makes a reading rise or fall?
| Influence | What it means for diagnosis |
| Exhaust flow | Pressure drop normally changes with flow. Compare measured values only at the manufacturer's specified engine conditions and flow, not against a single universal idle or road-speed figure. |
| Temperature and gas properties | Gas temperature and the control model influence the relationship between flow and pressure. A cold and a hot reading are not automatically comparable. |
| Soot loading | Accumulated soot can increase restriction. A successful regeneration oxidises soot under suitable conditions; a reading can change as the filter and operating state change. |
| Ash and permanent deposits | Non-combustible ash can remain after soot regeneration and contribute to restriction. Pressure alone cannot reliably separate soot and ash mass. Follow the manufacturer's service assessment. |
| Damaged filter or leak | A cracked substrate or exhaust leak can affect pressure and allow an unexpectedly low value; low restriction alone does not prove effective filtration. |
| Sensor, ports and hoses | Leaks, restrictions, melted sections, condensate, swapped connections, wiring or sensor offset can distort the measured value independently of filter condition. |
Pressure response is a system measurement. Soot, ash, exhaust flow, temperature and the actual sensor connection must be assessed together. A low static pressure does not prove the filter is intact or clean; a high value does not by itself prove the filter needs replacement. See soot and ash and particulate filter faults.
Pressure lines and sensor faults
Pressure pipes and hoses can crack, detach, chafe, melt, block with soot or collect condensate. A line restriction can delay or distort a response; a leak can cause an implausible signal. The result depends on which line and port are affected. Check the pressure take-offs as well as the visible hose. Before removing a line, record its routing and connections; use the correct heat-resistant specified replacements and clamps and route them away from heat and moving parts. Do not reverse inlet and outlet connections or blow compressed air through an attached sensor.
Electrical connectors can corrode, wires can fail from vibration or heat, and the sensor itself can drift or fail. A documented Mercedes-Benz service case identified hose and electrical issues among possible causes of sensor faults, while a HELLA Dacia Dokker example shows a cracked hose affecting plausibility. These are vehicle-specific examples. Mercedes-Benz service information.
Common problems: symptoms and checks
| Finding | Possible causes and first checks |
| DPF warning or regeneration faults | Pressure-sensor and hose faults can affect the load calculation, but a restricted filter or an engine problem can cause similar symptoms. Inspect ports, hoses and wiring, then compare pressure and regeneration data under specified conditions. |
| Pressure value changes slowly or appears implausible | A restricted, split, melted or disconnected line, blocked tapping or sensor fault can distort the result. Check both lines and their correct routing where fitted; use the applicable diagram and safe cooled-exhaust procedure. |
| High pressure or excessive soot-load estimate | Soot or ash restriction, a pressure-line problem or sensor offset are possible. Consider exhaust flow and temperature and use the manufacturer's test; a high reading alone cannot establish soot mass or condemn the filter. |
| Low or unexpected pressure | A pressure or exhaust leak, a damaged filter, an incorrect sensor or signal issue can affect the reading. A low pressure reading does not prove that the filter is intact or filtering properly. |
These findings require system-specific checks. HELLA: Dacia hose fault example; HELLA: aftertreatment diagnostics.
Fault codes and symptoms
Possible symptoms include a warning lamp, restricted power, regeneration problems, increased fuel consumption or a DPF warning. The same symptom can come from several components. Delphi lists P2452 for a pressure-sensor circuit, P2453 for circuit range/performance and P2454/P2455 for circuit low/high as examples. Code text, suffix and monitor conditions vary by vehicle; P2463 can relate to soot accumulation in a documented Chrysler application. An exhaust leak or defective hose can contribute to pressure-related codes. Delphi: differential-pressure sensor faults; FCA bulletin 18-054-15.
Workshop diagnosis
- Identify the system. Record the vehicle, engine, sensor location, fault codes, freeze-frame data, actual part number and relevant technical bulletins. Obtain the exhaust diagram and the diagnostic procedure for that engine and software.
- Check operating state. Record temperatures, engine speed and load, calculated or measured exhaust flow where available, the regeneration state and the unit used for the pressure. Compare like conditions and use the manufacturer's test limits.
- Inspect safely. Once the exhaust has cooled as required, inspect the sensor, connector, wiring, pressure ports, metal pipes, flexible hoses, clamps and routing. Look for cracks, leaks, chafing, crushed sections, condensation and restricted take-offs. Check for exhaust leaks and other aftertreatment faults.
- Check the zero or offset where specified. A no-flow key-on, engine-off reading can be a useful plausibility check on an applicable system, but its permitted offset, settling time and conditions come from the manufacturer. A value near zero does not prove accurate readings throughout the range, and a stored offset is not a universal fault. Do not open hot lines or infer a universal specification.
- Test the sensor and circuit. Follow the appropriate wiring diagram and approved test equipment for supply, ground and signal. If directed, compare the sensor's pressure response against a suitable calibrated pressure source and gauge over the specified range, with the correct port and pressure limits. Never compare volts numerically with a pressure value or apply arbitrary pressure to an unknown sensor.
- Assess filter and upstream causes. Investigate soot loading, ash, exhaust leaks, airflow, temperature and combustion or injection faults using the model-specific procedure. A pressure reading alone cannot distinguish a restricted filter from blocked pipes or an offset sensor.
- Repair and verify. Restore the correct hoses and connections, rectify the cause, then carry out the manufacturer's required adaptation or reset and confirm readings and fault status under specified conditions. Clear fault codes when appropriate, and record results.
Do not run a forced regeneration solely to clear a pressure fault. Ensure the underlying cause and the filter condition have been assessed and all manufacturer preconditions are satisfied. Exhaust parts and regeneration can reach hazardous temperatures: use the vehicle-specific process, suitable exhaust extraction and fire precautions. HSE: vehicle exhaust emissions.
Replacement, offset and learned values
Select the correct sensor for the actual vehicle, engine and system. Similar housings, connectors and number of hose stubs do not guarantee equal pressure range, offset, transfer curve, installation or compatibility. Some vehicles require a sensor offset adaptation after a sensor or hose repair; others use a different procedure. For example, FCA bulletin 18-054-15 specifies an offset reset on its listed 2010–2015 2.8-litre diesel application. That instruction is not authority to reset the filter soot or ash values on every vehicle. FCA service bulletin.
Distinguish a pressure-sensor zero or offset from a learned DPF soot or ash value. Reset or replacement functions can have different names and effects in different tools. Use only the exact function required for the repair; resetting an estimate does not clean a filter or remove ash. If the filter was cleaned or replaced, follow the applicable manufacturer procedure for that work separately.
Examples of pressure sensors and applications
The following are documented examples, not an exhaustive application catalogue. A bulletin describes only the vehicles, market, dates and conditions it lists; parts can be superseded or specified as an assembly with different hoses. Confirm the current part, engine, exhaust arrangement, emissions equipment and VIN with the manufacturer's parts information before ordering. A DPF pressure sensor is not necessarily the similarly named EGR pressure sensor or a particulate-matter sensor.
| Published sensor reference | Documented example and limits | Source and identification notes |
| Volkswagen Group 059 906 051 A; HELLA 6PP 009 409-231 | HELLA lists VW Touareg 7P5 diesel TDI, model years 2010–2014, in a regeneration fault case. | HELLA case. The case lists these two references; confirm the actual vehicle and current parts listing. |
| Audi 059 906 051 A | Audi campaign 23L2 covers selected 2009–2012 Audi Q7 3.0 TDI vehicles in the USA and Canada. | Audi campaign specifies the reference and shows two particulate-filter hoses. Campaign eligibility depends on VIN; it does not describe every Q7 worldwide. |
| FCA 56044587AB | FCA bulletin 18-054-15 specifies 2010–2015 Chrysler Town & Country, international market, with the ENS 2.8-litre diesel. | FCA service bulletin lists the sensor, connector kit and a procedure for its stated fault conditions. |
| Ford HC3Z-9J460-D | 2017–2018 F-Super Duty 6.7 L, built on or before 18 April 2018: pickup with 142-, 148- or 164-inch wheelbase. | Ford bulletin 18-2371. These are distinct service references for the stated US-market bulletin conditions, not general cross-references. |
| Ford HC3Z-9J460-F | Same bulletin: pickup with 160- or 176-inch wheelbase. |
| Ford HC3Z-9J460-E | Same bulletin: chassis cab. |
| Land Rover LR069660 | 2016 Range Rover (LG) 3.0 TDV6 Gen 2 in the North American bulletin's VIN range, single-speed transfer case. | JLR bulletin LTB01192NAS1 gives market and VIN restrictions and also lists specified Range Rover Sport vehicles. |
| Land Rover LR069684 | Same bulletin and market, twin-speed transfer case. |
| Cummins 5492073 / Emission Solutions A061B903 | Selected X15 CM2350 X114B, X116B and X123B aftertreatment configurations. | Cummins TSB200080 specifies different service kits by configuration; the sensor's larger ports require the corresponding larger tubes. |
| PACCAR 1818119 | Kenworth Canadian-registered chassis notice identifies the DPF differential-pressure sensor in selected 2017 MX-13 engines. | PACCAR/Kenworth E273 notice lists it separately from the PM sensor; scope is the notice's identified chassis. |
These examples show why matching a plug or a numerical part-family prefix is insufficient. Check whether the listed reference denotes a bare sensor, a complete sensor-and-line assembly, or a kit; compare the correct pressure connections and any required adaptation in current vehicle documentation.
Testing and UK MOT
A differential-pressure sensor monitors a pressure difference or a pressure used in a particular model; it is not a smoke meter, a particle-number counter or a NOx sensor. A low pressure reading does not demonstrate particle-filter efficiency. The DVSA MOT inspection manual, section 8 specifies applicable visible emissions-equipment, malfunction-indicator and smoke checks and exemptions; do not assume a routine MOT includes a dedicated differential-pressure accuracy test. See emissions testing equipment.
Sources and related reading