MoTeC CDL3 (MoTeC part #18022) is a motorsport display and acquisition device. The information here is specific to the cited part; check the label, hardware revision, options and vehicle protocol before connection.

Specifications and options
- Backlit monochrome display with a 70-segment bar graph and 13-character text bar, configurable pages and alerts.
- Logging is optional: the data-logging upgrade adds 8 MB storage, with logging rates up to 500 samples per second.
- Two configurable CAN or RS232 buses and a dedicated RS232 connection; additional analogue, temperature and auxiliary functions depend on the I/O upgrade.
- Configuration is performed with MoTeC software; match the ECU interface and enabled options before installation.
Connector and pinout
34-way AMP: the table below follows the manufacturer’s pinout for part #18022. Check cavity numbering and the manufacturer's connector view; the functional map is not a physical connector-face drawing. Blank cells retain the source's unspecified function; do not assign them by assumption. Inputs marked as optional need the appropriate enabled upgrade.
| Pin | Name | Standard function | Optional function |
|---|---|---|---|
| 1 | E-TX- | Ethernet Transmit - | |
| 2 | E-TX+ | Ethernet Transmit + | |
| 3 | AV1 | Analogue Voltage Input 1 | |
| 4 | AV2 | Analogue Voltage Input 2 | |
| 5 | AV3 | Analogue Voltage Input 3 | |
| 6 | AV4 | Analogue Voltage Input 4 | |
| 7 | 8V | Sensor 8 V | |
| 8 | 5V | Sensor 5 V | |
| 9 | 0V | Sensor 0 V | |
| 10 | E-RX- | Ethernet Receive - | |
| 11 | E-RX+ | Ethernet Receive + | |
| 12 | |||
| 13 | |||
| 14 | DIG1 | Alarm Ack* | Digital Input 1 |
| 15 | DIG2 | Next Line* | Digital Input 2 |
| 16 | AT1 | Analogue Temp Input 1 | |
| 17 | AT2 | Analogue Temp Input 2 | |
| 18 | CAN0L / RS232 0 GND | CAN0 Lo / RS232 0 GND | |
| 19 | CAN0H / RS232 0 RX | CAN0 Hi / RS232 0 RX | |
| 20 | TX | RS232 Output | |
| 21 | SPD1 | Speed Input 1 | |
| 22 | SPD2 | Speed Input 2 | |
| 23 | SPD3 | Brightness Switch | Speed Input 3 |
| 24 | |||
| 25 | |||
| 26 | CAN1L / RS232 1 GND | CAN1 Lo / RS232 1 GND | |
| 27 | CAN1H / RS232 1 RX | CAN1 Hi / RS232 1 RX | |
| 28 | RX | RS232 Input | |
| 29 | AUX1 | Auxiliary Output 1 | |
| 30 | AUX2 | Auxiliary Output 2 | |
| 31 | AUX3 | Auxiliary Output 3 | |
| 32 | AUX4 | Auxiliary Output 4 | |
| 33 | BAT+ | Battery Positive | |
| 34 | BAT- | Battery Negative |
Wiring and configuration
Use the correct connector, power and sensor return for this unit. Match CAN high and low to a compatible, correctly configured network and check existing termination. ECU channels, sensors and lap timing depend on the specific hardware, protocol, configuration and licensed options. Use manufacturer instructions for wire gauge, supply protection and continuity checks; do not connect vehicle battery voltage to a sensor reference output.
MoTeC i2 supports reviewing recorded data; Pro analysis and T2 telemetry require the applicable upgrades. A telemetry licence alone does not provide a radio or cellular connection. See the MoTeC manufacturer guide for family comparisons and references.