Tuning Wiki
Browse MoTeC

MoTeC CDL3 (MoTeC part #18022) is a motorsport display and acquisition device. The information here is specific to the cited part; check the label, hardware revision, options and vehicle protocol before connection.

MoTeC CDL3 product photograph
MoTeC CDL3. Image: MoTeC, reproduced with permission. Manufacturer product page and specifications.

Specifications and options

  • Backlit monochrome display with a 70-segment bar graph and 13-character text bar, configurable pages and alerts.
  • Logging is optional: the data-logging upgrade adds 8 MB storage, with logging rates up to 500 samples per second.
  • Two configurable CAN or RS232 buses and a dedicated RS232 connection; additional analogue, temperature and auxiliary functions depend on the I/O upgrade.
  • Configuration is performed with MoTeC software; match the ECU interface and enabled options before installation.

Connector and pinout

34-way AMP: the table below follows the manufacturer’s pinout for part #18022. Check cavity numbering and the manufacturer's connector view; the functional map is not a physical connector-face drawing. Blank cells retain the source's unspecified function; do not assign them by assumption. Inputs marked as optional need the appropriate enabled upgrade.

PinNameStandard functionOptional function
1E-TX-Ethernet Transmit -
2E-TX+Ethernet Transmit +
3AV1Analogue Voltage Input 1
4AV2Analogue Voltage Input 2
5AV3Analogue Voltage Input 3
6AV4Analogue Voltage Input 4
78VSensor 8 V
85VSensor 5 V
90VSensor 0 V
10E-RX-Ethernet Receive -
11E-RX+Ethernet Receive +
12
13
14DIG1Alarm Ack*Digital Input 1
15DIG2Next Line*Digital Input 2
16AT1Analogue Temp Input 1
17AT2Analogue Temp Input 2
18CAN0L / RS232 0 GNDCAN0 Lo / RS232 0 GND
19CAN0H / RS232 0 RXCAN0 Hi / RS232 0 RX
20TXRS232 Output
21SPD1Speed Input 1
22SPD2Speed Input 2
23SPD3Brightness SwitchSpeed Input 3
24
25
26CAN1L / RS232 1 GNDCAN1 Lo / RS232 1 GND
27CAN1H / RS232 1 RXCAN1 Hi / RS232 1 RX
28RXRS232 Input
29AUX1Auxiliary Output 1
30AUX2Auxiliary Output 2
31AUX3Auxiliary Output 3
32AUX4Auxiliary Output 4
33BAT+Battery Positive
34BAT-Battery Negative

Wiring and configuration

MoTeC CDL3 simplified power and CAN wiring
Power and CAN example, functional schematic rather than connector geometry. Original Tuning Wiki illustration based on the MoTeC product pinout; verify the actual harness and matching ECU.

Use the correct connector, power and sensor return for this unit. Match CAN high and low to a compatible, correctly configured network and check existing termination. ECU channels, sensors and lap timing depend on the specific hardware, protocol, configuration and licensed options. Use manufacturer instructions for wire gauge, supply protection and continuity checks; do not connect vehicle battery voltage to a sensor reference output.

MoTeC i2 supports reviewing recorded data; Pro analysis and T2 telemetry require the applicable upgrades. A telemetry licence alone does not provide a radio or cellular connection. See the MoTeC manufacturer guide for family comparisons and references.

Data analysis software

MoTeC i2 data analysis with channel traces and gauges
MoTeC i2 data analysis showing channel traces and gauges. Image: MoTeC, reproduced with permission; manufacturer image.

The CDL3 needs its applicable data-logging upgrade or a logging-equipped kit before it can produce recordings for analysis. MoTeC i2 reviews recorded channels in graphs and reports; i2 Pro features depend on the device upgrade or applicable software licence. See the manufacturer model and analysis comparison and i2 software and licence information.

Retrieve a recording with the compatible MoTeC device manager, then open it in i2 to compare channels and laps when suitable position data has been recorded. Download MoTeC software from the official downloads library; see the MoTeC manufacturer guide for the Standard and Pro options.