Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Simos 18
Applies to
Simos 18.1
Tool groups
None
Manufacturers
Volkswagen Group

Scope: Simos engineering names are examples from the community SC8S5031_C_OEM Simos 18.1 cross-reference unless a different source is named. Match ECU and gearbox hardware, engine, ASW, calibration, definition and any patches. Verify axes, units, array indices, signs, selectors and logger scaling: extracted labels can conflict. Product display names are not necessarily OEM identifiers. SC8S5031 reference.

ECU and TCU have separate jobs

The engine ECU reports modelled torque and responds to gearbox torque requests. The transmission controller has its own torque limits, clutch, hydraulic, shift and adaptation controls. The EcuTek DQ250 and DQ381 guides describe use of engine torque in their documented systems, including pressure control; both identify accurate ECU torque estimation as important. A lower reported torque is not a measurement of reduced clutch load. The EcuTek pressure derivation includes stated uncertainty and should not be generalised to every DSG.

Simos ECU intervention examples

The SC8S5031 TRSM gearbox-intervention reference identifies ip_t_tq_gb_intv_down[2] and ip_t_tq_gb_intv_up[2] as ramp times down or up to driver request at the end of a gearbox intervention. The published example uses transmission-related speed and gear axes, with time in seconds. They are engine-ECU post-intervention ramp calibrations, not TCU shift-duration maps; confirm index, selectors and direction in the actual software.

lv_tq_gb_intv_ramp_down, lv_tq_gb_intv_ramp_up and state_gb_intv_dec_fast are runtime flags/state, not calibration maps. Check the logger's enum and timing; a state alone does not prove the cause of a shift complaint. ip_tq_lim_gb_prot_max_dct is a separate ECU-side gearbox-protection clutch-torque limit, with rpm and gear axes in the published TRSM protection example; it is not a gearbox pressure control.

DQ250 six-speed example

EcuTek's DQ250 guide uses product labels including Clutch Target Torque Correction Clutch 1 & 2, Maximum Torque Clutch 1 & 2 and Line Pressure Setpoint (torque). Its interpretation of some pressure and protection calculations is qualified by the author. These are TCU controls for the documented example, not Simos ECU identifiers or recommended values. Pressure request, actual pressure, solenoid current, clutch slip and adaptation are distinct. See the existing DQ250 clutch-pressure and adaptation guide.

DQ381 seven-speed example

The EcuTek DQ381 guide describes TCU labels Torque Actual (& Efficiency), Torque Limit (Depleting & Efficiency), Maximum Torque (gearbox protection), Maximum Torque (temperature), Target Torque P4 1 & 2 and Target Pressure P4 1 & 2. EcuTek describes P4 targets in the adaptation context and explicitly notes that its torque-to-pressure derivation is not fully documented. Preserve that uncertainty and check the exact TCU and tool definition. These limits and requests do not establish actual pressure or physical torque capacity.

The COBB seven-speed guide also uses product labels Target Gear Change Time and Clutch Overlap. Shift time, overlap, torque reduction and clutch pressure interact; a shorter table target alone does not establish a completed or mechanically sound shift. COBB's six-speed guide describes its six-speed schedules with axle torque and throttle axes and engine-speed output, unlike its documented seven-speed schedules with vehicle-speed output. Verify gear, mode, direction, ratios and actual TCU software before comparing or transferring a schedule.

Logging and adaptation

Where supported, align ECU and TCU timestamps and compare engine torque request/limit/estimate, throttle, ignition, engine speed and gear with the gearbox's reported engine torque, target gear, shift state, torque-reduction request and active state, clutch speeds/slip, pressure and gearbox temperature. COBB lists (DSG)Engine Torque, (DSG)Torque Reduction Request, (DSG)Torque Reduction Active, (DSG)Clutch 1 Slip, (DSG)Clutch 2 Slip, (DSG)Line Pressure and (DSG)Line Pressure Set Point for selected MQB vehicles. It notes some intervention flags have unknown full enumerations; these are monitors rather than maps and are not available on every vehicle. COBB DSG monitor list. Compare actual and target quantities and remember controlled slip can occur during an intended handover.

EcuTek specifies adaptation after programming in its documented DQ250 and DQ381 workflows; consult the correct current vehicle, software and tool procedure, capture faults and existing state, and do not assume a blanket reset is appropriate for every flash or complaint. A large numeric torque field or patched representation is not a verified clutch, gearbox or hardware rating.

Related: torque and DSG overview · torque model calibration · DSG torque coordination · DQ250 pressure and adaptation · bigger turbo tuning · log diagnosis.