Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Datalogging and telematics
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
RACELOGIC

Changes from revision 6 to revision 11

Removed text is struck through; added text is highlighted.

Overview

RACELOGIC's VBOX Motorsport range uses satellite positioning for circuit driving, driver coaching and motorsport analysis. Different models add vehicle data, a driver display or synchronised video. Video VBOX products record the data used in the video overlay as well as footage for later comparison. Features vary by model and hardware generation; check the exact part number before specifying a system. [1]

Manufacturer photographs: VBOX Video HD1 · VBOX Video HD2 and analysis software. Images: RACELOGIC / VBOX Motorsport; rights remain with the manufacturer.

Models

Individual model pages: VBOX Video HD1 · VBOX Video HD2 · LapTimer S · LapTimer R · Mini LapTimer.

VBOX LapTimer and Mini LapTimer

The VBOX LapTimer family combines a driver display with GNSS data logging to an SD card. It provides lap timing, position-based predictive delta time and speed comparison LEDs; data can be reviewed in Circuit Tools after the session. The manufacturer lists the Mini LapTimer at 10 Hz and current LapTimer S and R versions at 25 Hz, with side and rear connectors respectively. Hardware generations differ: check the part number and manual. The LapTimer is not itself a Video HD1 or HD2 camera system. The product page also contains RACELOGIC photographs. LapTimer S datasheet.

VBOX Video HD1

VBOX Video HD1. Image: RACELOGIC; reproduced with permission. Manufacturer source.

HD1 integrates a single video camera, GNSS antenna and recorder in a compact vehicle-powered unit. It records 1920 × 1080 video at 30 frames per second and 25 Hz multi-constellation GNSS data, with an overlay including lap times, position, speed and g-force. It has two isolated CAN interfaces supporting CAN 2.0 and CAN FD, and can log up to 80 CAN channels. Speed-triggered recording, an HDMI output and optional predictive lap timing display are available. Circuit Tools 3 is included. [2] [1]

VBOX Video HD2 / HDMI

VBOX Video HD2 and HD2 HDMI equipment. Image: RACELOGIC; reproduced with permission. Manufacturer source.

HD2 accepts two camera inputs and synchronises 1080p30 video with position and vehicle data; the current 25 Hz version supports a customisable overlay and up to 80 CAN channels. The optional OLED display provides predictive lap timing. HDMI is provided on the HDMI variant. Older versions of HD2 used 10 Hz GNSS; identify the hardware version and consult the appropriate manual and datasheet rather than assuming all units have 25 Hz or HDMI. [3] [4] [5]

Live video with HD2 HDMI

The HD2 HDMI variant can output real-time video and audio to an HDMI-compatible monitor, recorder or separate streaming device. RACELOGIC describes using a LiveU Solo HDMI encoder to transmit HD2 video to remote viewers, including back to the pits. This requires the HDMI-equipped HD2, suitable cable, separate encoder, network connectivity and relevant service arrangements. HDMI output alone is not an internet connection or a remote numeric telemetry feed. Coverage, network capacity and delay affect a live stream; the locally recorded data and video can also be reviewed later. Check the HD2 product information for compatible firmware and setup software and confirm event rules before transmitting.

Analysis and setup

Step-by-step: review a session in Circuit Tools 3This walkthrough is for the Windows edition of Circuit Tools 3. The macOS and iOS editions have different interfaces and support limitations; select the version appropriate for the recording. A LapTimer alone does not create a video recording.Install the software. Download Circuit Tools 3 for Windows from the RACELOGIC software page and install it. Copy the session. Stop the logger and copy the .VBO data file and any associated video files from its SD card into a folder on the computer. Keep the associated files together for video playback. Open the recording. In Circuit Tools 3 choose File → Load, or drag the VBO file into the application. The software uses GPS data and its track database to identify the circuit when possible.Circuit Tools 3 File menu: choose Load VBO or DBN File at the top. The highlighted Load Circuit Overlay item is a different function. Image: RACELOGIC, reproduced with permission; source and guide. Check the track and laps. Review the track map and laps pane. If the circuit is not in the database, set its start/finish line on the track map. Confirm that the laps and sectors match the layout driven. Choose a reference. In the laps pane, tick Show for two laps. The fastest is selected as the reference by default; use the Ref box if a different comparison lap is needed. Compare the data. Use the graph and track-map panes to compare speed and the time-difference trace by position. Choose additional recorded channels through Channels, and play synchronised video if the session has compatible linked footage. Inspect the same corner across the two laps rather than relying on lap time alone.Circuit Tools 3: example video comparison for multiple laps; linked compatible video must be present. Image: RACELOGIC, reproduced with permission; source and guide. Review the result. Use Measure or Reports where useful, and save or export a selected lap or video through the File options. Available functions depend on the files and software edition.Source: RACELOGIC Circuit Tools 3 quick-start guide; see also the iOS guide and custom-track limitation.Circuit Tools comparing simulator laps with video, data traces and a track map; this image shows the earlier Circuit Tools interface. Image: RACELOGIC, reproduced with permission; manufacturer source.Circuit Tools is RACELOGIC's free motorsport analysis software for compatible VBOX recordings. Circuit Tools 3 for Windows loads a .VBO session, identifies supported circuits, and synchronises the lap list, track map, graphs and available video. Compare laps or sectors and use the time-difference trace to see where time was gained or lost. Circuit Tools 3 quick-start guide.Getting started: copy the .VBO data and associated video files from the SD card to the computer, load the recording, and select laps to compare. Video playback requires a recording with compatible video files. Circuit Tools is available for Windows, macOS and iOS; the manufacturer's software download page lists the available versions and platform requirements. The iOS and macOS editions support circuit files; check the edition's documentation for feature and file support. The iOS guide notes that unrecognised custom tracks require the Windows application.VBOX Test Suite is a separate Windows package for performance testing, whereas Circuit Tools focuses on circuit and driver analysis. Availability of CAN channels, video and review features depends on the logger, recorded data and application edition. RACELOGIC software downloads.

Circuit Tools allows comparison of laps, position on track, sector and delta times, and synchronised video. Use speed traces and available brake, throttle and gear channels to investigate where time was gained or lost. HD1 is configured using VBOX Video Setup and offers phone-based camera preview; HD2's setup software configures the logger, CAN channels and overlay layout. The capabilities of an analysis installation may vary by software version. [2] [6]

Vehicle data and installation considerations

Position, speed and lap timing come from GNSS; engine speed, throttle, brake pressure and other vehicle parameters need an appropriate source and a correctly configured interface. A listed channel is not proof that a particular vehicle or ECU broadcasts it. [3] Confirm the vehicle's CAN protocol, supported channels, wiring, bitrate, and the logger's hardware version before purchase or connection. HD1 has CAN FD; HD2 capabilities and available accessories depend on version. [2] [4] RACELOGIC describes connecting HD2 to AiM dashboards and to MoTeC equipment, with model-specific wiring and setup. Read its integration guidance and check the channel configuration. [3] Mount and secure the equipment and antenna in accordance with manufacturer guidance and the event or series rules. Confirm recording, satellite reception and channel scaling with a stationary and low-speed check before relying on a session.

Connectors, pinouts and cabling

Original Tuning Wiki connection map; schematic positions are not connector-face geometry. Source: RACELOGIC HD1 pinouts and HD2 pinouts.

Identify the exact model and hardware generation before wiring. The pin numbers below follow the manufacturer’s numbered connector diagrams; consult the linked drawings for the connector face and orientation, and distinguish the device socket from the mating cable’s wire side. RS232 TX and RX are labelled from the device documentation; check the other device’s direction. Disconnect power while checking continuity and individually insulate unused leads.

VBOX Video HD1 — Hirose power and communications

Original Tuning Wiki functional wiring illustration for HD1 COM1; not a connector-face view. Based on RACELOGIC's HD1 pinout. Verify the loom and vehicle power before connection.

RACELOGIC’s HD1 pinout lists the same six pin assignments for both power/communications HR30 connectors, with the OLED display supported only on COM1. The separate hardware overview identifies COM1 with CAN 1 and the second power/communications connector with CAN 2, while the pinout page describes both as CAN 1. Confirm the individual bus selection and hardware with RACELOGIC before wiring; the shared pin labels alone do not resolve that documentation conflict.

PinHD1 six-pin Hirose HR30 function1RS232 RX2RS232 TX3Ground4CAN low5CAN high6Power

The same pinout lists the separate three-pin external microphone connector: 1 audio in, 2 mic bias, 3 audio ground. The hardware overview specifies 6–18 V DC supply and separate GNSS antenna and micro-HDMI connections; HDMI output needs an external recorder or streaming encoder for remote video.

For the manufacturer's HD1 installation harness, red is nominal +12 V, blue ground, yellow CAN high and green CAN low. Those colours apply to that harness only; verify the cable supplied. The manufacturer recommends ignition-switched power and cautions against connection to a jump-start lead or charger under load.

VBOX Video HD2 — power and CAN/serial

The HD2 pinout and rear-panel drawing shows separate LEMO connectors. Its two-pin POWER connector has pin 1 power positive and pin 2 ground; chassis is ground. The five-pin CAN/SER connector is a different socket from the five-pin USB connector.

PinHD2 five-pin CAN/SER function1RS232 TX2RS232 RX3CAN high4CAN low5+V power output

For completeness, the separate five-pin HD2 USB connector is documented as 1 USB ID, 2 DP, 3 ground, 4 USB 5 V and 5 DM. The two nine-pin camera connectors and four-pin microphone are also shown in the manufacturer’s pinout. Do not assume any HD1, HD Lite or vehicle connector has the HD2 assignment.

RACELOGIC’s HD2 CAN connection guide identifies RLCAB069L for OBD-II, RLCAB015L for bare-wire CAN and RLACS182L for clipping onto a CAN pair; check compatibility with the hardware generation and display arrangement. A physical OBD-II connection does not prove that the desired ECU channels are available: configure the correct CAN bitrate and channel decoding for the vehicle.

Sources and further reading

RACELOGIC: VBOX Motorsport product overview.RACELOGIC: VBOX Video HD1.RACELOGIC: VBOX Video HD2.RACELOGIC: product documentation and version-specific datasheets.RACELOGIC: VBOX Video HDMI 25 Hz datasheet.RACELOGIC: VBOX Video HD2 Setup software.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 6: RACELOGIC VBOX Motorsport data loggers

Overview

RACELOGIC's VBOX Motorsport range uses satellite positioning for circuit driving, driver coaching and motorsport analysis. Different models add vehicle data, a driver display or synchronised video. Video VBOX products record the data used in the video overlay as well as footage for later comparison. Features vary by model and hardware generation; check the exact part number before specifying a system. [1]

Manufacturer photographs: VBOX Video HD1 · VBOX Video HD2 and analysis software. Images: RACELOGIC / VBOX Motorsport; rights remain with the manufacturer.

Models

Individual model pages: VBOX Video HD1 · VBOX Video HD2 · LapTimer S · LapTimer R · Mini LapTimer.

VBOX LapTimer and Mini LapTimer

The VBOX LapTimer family combines a driver display with GNSS data logging to an SD card. It provides lap timing, position-based predictive delta time and speed comparison LEDs; data can be reviewed in Circuit Tools after the session. The manufacturer lists the Mini LapTimer at 10 Hz and current LapTimer S and R versions at 25 Hz, with side and rear connectors respectively. Hardware generations differ: check the part number and manual. The LapTimer is not itself a Video HD1 or HD2 camera system. The product page also contains RACELOGIC photographs. LapTimer S datasheet.

VBOX Video HD1

RACELOGIC VBOX Video HD1 camera logger
VBOX Video HD1. Image: RACELOGIC; reproduced with permission. Manufacturer source.

HD1 integrates a single video camera, GNSS antenna and recorder in a compact vehicle-powered unit. It records 1920 × 1080 video at 30 frames per second and 25 Hz multi-constellation GNSS data, with an overlay including lap times, position, speed and g-force. It has two isolated CAN interfaces supporting CAN 2.0 and CAN FD, and can log up to 80 CAN channels. Speed-triggered recording, an HDMI output and optional predictive lap timing display are available. Circuit Tools 3 is included. [2] [1]

VBOX Video HD2 / HDMI

RACELOGIC VBOX Video HD2 and HD2 HDMI logger units
VBOX Video HD2 and HD2 HDMI equipment. Image: RACELOGIC; reproduced with permission. Manufacturer source.

HD2 accepts two camera inputs and synchronises 1080p30 video with position and vehicle data; the current 25 Hz version supports a customisable overlay and up to 80 CAN channels. The optional OLED display provides predictive lap timing. HDMI is provided on the HDMI variant. Older versions of HD2 used 10 Hz GNSS; identify the hardware version and consult the appropriate manual and datasheet rather than assuming all units have 25 Hz or HDMI. [3] [4] [5]

Live video with HD2 HDMI

The HD2 HDMI variant can output real-time video and audio to an HDMI-compatible monitor, recorder or separate streaming device. RACELOGIC describes using a LiveU Solo HDMI encoder to transmit HD2 video to remote viewers, including back to the pits. This requires the HDMI-equipped HD2, suitable cable, separate encoder, network connectivity and relevant service arrangements. HDMI output alone is not an internet connection or a remote numeric telemetry feed. Coverage, network capacity and delay affect a live stream; the locally recorded data and video can also be reviewed later. Check the HD2 product information for compatible firmware and setup software and confirm event rules before transmitting.

Analysis and setup

Circuit Tools allows comparison of laps, position on track, sector and delta times, and synchronised video. Use speed traces and available brake, throttle and gear channels to investigate where time was gained or lost. HD1 is configured using VBOX Video Setup and offers phone-based camera preview; HD2's setup software configures the logger, CAN channels and overlay layout. The capabilities of an analysis installation may vary by software version. [2] [6]

Vehicle data and installation considerations

  • Position, speed and lap timing come from GNSS; engine speed, throttle, brake pressure and other vehicle parameters need an appropriate source and a correctly configured interface. A listed channel is not proof that a particular vehicle or ECU broadcasts it. [3]
  • Confirm the vehicle's CAN protocol, supported channels, wiring, bitrate, and the logger's hardware version before purchase or connection. HD1 has CAN FD; HD2 capabilities and available accessories depend on version. [2] [4]
  • RACELOGIC describes connecting HD2 to AiM dashboards and to MoTeC equipment, with model-specific wiring and setup. Read its integration guidance and check the channel configuration. [3]
  • Mount and secure the equipment and antenna in accordance with manufacturer guidance and the event or series rules. Confirm recording, satellite reception and channel scaling with a stationary and low-speed check before relying on a session.

Connectors, pinouts and cabling

Schematic contact maps of VBOX HD1 six-pin and HD2 five-pin connections
Original Tuning Wiki connection map; schematic positions are not connector-face geometry. Source: RACELOGIC HD1 pinouts and HD2 pinouts.

Identify the exact model and hardware generation before wiring. The pin numbers below follow the manufacturer’s numbered connector diagrams; consult the linked drawings for the connector face and orientation, and distinguish the device socket from the mating cable’s wire side. RS232 TX and RX are labelled from the device documentation; check the other device’s direction. Disconnect power while checking continuity and individually insulate unused leads.

VBOX Video HD1 — Hirose power and communications

Schematic wiring paths for VBOX HD1 COM1 power and CAN
Original Tuning Wiki functional wiring illustration for HD1 COM1; not a connector-face view. Based on RACELOGIC's HD1 pinout. Verify the loom and vehicle power before connection.

RACELOGIC’s HD1 pinout lists the same six pin assignments for both power/communications HR30 connectors, with the OLED display supported only on COM1. The separate hardware overview identifies COM1 with CAN 1 and the second power/communications connector with CAN 2, while the pinout page describes both as CAN 1. Confirm the individual bus selection and hardware with RACELOGIC before wiring; the shared pin labels alone do not resolve that documentation conflict.

PinHD1 six-pin Hirose HR30 function
1RS232 RX
2RS232 TX
3Ground
4CAN low
5CAN high
6Power

The same pinout lists the separate three-pin external microphone connector: 1 audio in, 2 mic bias, 3 audio ground. The hardware overview specifies 6–18 V DC supply and separate GNSS antenna and micro-HDMI connections; HDMI output needs an external recorder or streaming encoder for remote video.

For the manufacturer's HD1 installation harness, red is nominal +12 V, blue ground, yellow CAN high and green CAN low. Those colours apply to that harness only; verify the cable supplied. The manufacturer recommends ignition-switched power and cautions against connection to a jump-start lead or charger under load.

VBOX Video HD2 — power and CAN/serial

The HD2 pinout and rear-panel drawing shows separate LEMO connectors. Its two-pin POWER connector has pin 1 power positive and pin 2 ground; chassis is ground. The five-pin CAN/SER connector is a different socket from the five-pin USB connector.

PinHD2 five-pin CAN/SER function
1RS232 TX
2RS232 RX
3CAN high
4CAN low
5+V power output

For completeness, the separate five-pin HD2 USB connector is documented as 1 USB ID, 2 DP, 3 ground, 4 USB 5 V and 5 DM. The two nine-pin camera connectors and four-pin microphone are also shown in the manufacturer’s pinout. Do not assume any HD1, HD Lite or vehicle connector has the HD2 assignment.

RACELOGIC’s HD2 CAN connection guide identifies RLCAB069L for OBD-II, RLCAB015L for bare-wire CAN and RLACS182L for clipping onto a CAN pair; check compatibility with the hardware generation and display arrangement. A physical OBD-II connection does not prove that the desired ECU channels are available: configure the correct CAN bitrate and channel decoding for the vehicle.

Sources and further reading

  1. RACELOGIC: VBOX Motorsport product overview.
  2. RACELOGIC: VBOX Video HD1.
  3. RACELOGIC: VBOX Video HD2.
  4. RACELOGIC: product documentation and version-specific datasheets.
  5. RACELOGIC: VBOX Video HDMI 25 Hz datasheet.
  6. RACELOGIC: VBOX Video HD2 Setup software.
Revision 11: RACELOGIC VBOX Motorsport data loggers

Overview

RACELOGIC's VBOX Motorsport range uses satellite positioning for circuit driving, driver coaching and motorsport analysis. Different models add vehicle data, a driver display or synchronised video. Video VBOX products record the data used in the video overlay as well as footage for later comparison. Features vary by model and hardware generation; check the exact part number before specifying a system. [1]

Manufacturer photographs: VBOX Video HD1 · VBOX Video HD2 and analysis software. Images: RACELOGIC / VBOX Motorsport; rights remain with the manufacturer.

Models

Individual model pages: VBOX Video HD1 · VBOX Video HD2 · LapTimer S · LapTimer R · Mini LapTimer.

VBOX LapTimer and Mini LapTimer

The VBOX LapTimer family combines a driver display with GNSS data logging to an SD card. It provides lap timing, position-based predictive delta time and speed comparison LEDs; data can be reviewed in Circuit Tools after the session. The manufacturer lists the Mini LapTimer at 10 Hz and current LapTimer S and R versions at 25 Hz, with side and rear connectors respectively. Hardware generations differ: check the part number and manual. The LapTimer is not itself a Video HD1 or HD2 camera system. The product page also contains RACELOGIC photographs. LapTimer S datasheet.

VBOX Video HD1

RACELOGIC VBOX Video HD1 camera logger
VBOX Video HD1. Image: RACELOGIC; reproduced with permission. Manufacturer source.

HD1 integrates a single video camera, GNSS antenna and recorder in a compact vehicle-powered unit. It records 1920 × 1080 video at 30 frames per second and 25 Hz multi-constellation GNSS data, with an overlay including lap times, position, speed and g-force. It has two isolated CAN interfaces supporting CAN 2.0 and CAN FD, and can log up to 80 CAN channels. Speed-triggered recording, an HDMI output and optional predictive lap timing display are available. Circuit Tools 3 is included. [2] [1]

VBOX Video HD2 / HDMI

RACELOGIC VBOX Video HD2 and HD2 HDMI logger units
VBOX Video HD2 and HD2 HDMI equipment. Image: RACELOGIC; reproduced with permission. Manufacturer source.

HD2 accepts two camera inputs and synchronises 1080p30 video with position and vehicle data; the current 25 Hz version supports a customisable overlay and up to 80 CAN channels. The optional OLED display provides predictive lap timing. HDMI is provided on the HDMI variant. Older versions of HD2 used 10 Hz GNSS; identify the hardware version and consult the appropriate manual and datasheet rather than assuming all units have 25 Hz or HDMI. [3] [4] [5]

Live video with HD2 HDMI

The HD2 HDMI variant can output real-time video and audio to an HDMI-compatible monitor, recorder or separate streaming device. RACELOGIC describes using a LiveU Solo HDMI encoder to transmit HD2 video to remote viewers, including back to the pits. This requires the HDMI-equipped HD2, suitable cable, separate encoder, network connectivity and relevant service arrangements. HDMI output alone is not an internet connection or a remote numeric telemetry feed. Coverage, network capacity and delay affect a live stream; the locally recorded data and video can also be reviewed later. Check the HD2 product information for compatible firmware and setup software and confirm event rules before transmitting.

Analysis and setup

Step-by-step: review a session in Circuit Tools 3

This walkthrough is for the Windows edition of Circuit Tools 3. The macOS and iOS editions have different interfaces and support limitations; select the version appropriate for the recording. A LapTimer alone does not create a video recording.

  1. Install the software. Download Circuit Tools 3 for Windows from the RACELOGIC software page and install it.
  2. Copy the session. Stop the logger and copy the .VBO data file and any associated video files from its SD card into a folder on the computer. Keep the associated files together for video playback.
  3. Open the recording. In Circuit Tools 3 choose File → Load, or drag the VBO file into the application. The software uses GPS data and its track database to identify the circuit when possible.
    Circuit Tools 3 File menu showing Load VBO or DBN File
    Circuit Tools 3 File menu: choose Load VBO or DBN File at the top. The highlighted Load Circuit Overlay item is a different function. Image: RACELOGIC, reproduced with permission; source and guide.
  4. Check the track and laps. Review the track map and laps pane. If the circuit is not in the database, set its start/finish line on the track map. Confirm that the laps and sectors match the layout driven.
  5. Choose a reference. In the laps pane, tick Show for two laps. The fastest is selected as the reference by default; use the Ref box if a different comparison lap is needed.
  6. Compare the data. Use the graph and track-map panes to compare speed and the time-difference trace by position. Choose additional recorded channels through Channels, and play synchronised video if the session has compatible linked footage. Inspect the same corner across the two laps rather than relying on lap time alone.
    Circuit Tools 3 showing multiple synchronised video panes
    Circuit Tools 3: example video comparison for multiple laps; linked compatible video must be present. Image: RACELOGIC, reproduced with permission; source and guide.
  7. Review the result. Use Measure or Reports where useful, and save or export a selected lap or video through the File options. Available functions depend on the files and software edition.

Source: RACELOGIC Circuit Tools 3 quick-start guide; see also the iOS guide and custom-track limitation.

Circuit Tools lap comparison showing simulator video, graphs and track map
Circuit Tools comparing simulator laps with video, data traces and a track map; this image shows the earlier Circuit Tools interface. Image: RACELOGIC, reproduced with permission; manufacturer source.

Circuit Tools is RACELOGIC's free motorsport analysis software for compatible VBOX recordings. Circuit Tools 3 for Windows loads a .VBO session, identifies supported circuits, and synchronises the lap list, track map, graphs and available video. Compare laps or sectors and use the time-difference trace to see where time was gained or lost. Circuit Tools 3 quick-start guide.

Getting started: copy the .VBO data and associated video files from the SD card to the computer, load the recording, and select laps to compare. Video playback requires a recording with compatible video files. Circuit Tools is available for Windows, macOS and iOS; the manufacturer's software download page lists the available versions and platform requirements. The iOS and macOS editions support circuit files; check the edition's documentation for feature and file support. The iOS guide notes that unrecognised custom tracks require the Windows application.

VBOX Test Suite is a separate Windows package for performance testing, whereas Circuit Tools focuses on circuit and driver analysis. Availability of CAN channels, video and review features depends on the logger, recorded data and application edition. RACELOGIC software downloads.

Circuit Tools allows comparison of laps, position on track, sector and delta times, and synchronised video. Use speed traces and available brake, throttle and gear channels to investigate where time was gained or lost. HD1 is configured using VBOX Video Setup and offers phone-based camera preview; HD2's setup software configures the logger, CAN channels and overlay layout. The capabilities of an analysis installation may vary by software version. [2] [6]

Vehicle data and installation considerations

  • Position, speed and lap timing come from GNSS; engine speed, throttle, brake pressure and other vehicle parameters need an appropriate source and a correctly configured interface. A listed channel is not proof that a particular vehicle or ECU broadcasts it. [3]
  • Confirm the vehicle's CAN protocol, supported channels, wiring, bitrate, and the logger's hardware version before purchase or connection. HD1 has CAN FD; HD2 capabilities and available accessories depend on version. [2] [4]
  • RACELOGIC describes connecting HD2 to AiM dashboards and to MoTeC equipment, with model-specific wiring and setup. Read its integration guidance and check the channel configuration. [3]
  • Mount and secure the equipment and antenna in accordance with manufacturer guidance and the event or series rules. Confirm recording, satellite reception and channel scaling with a stationary and low-speed check before relying on a session.

Connectors, pinouts and cabling

Schematic contact maps of VBOX HD1 six-pin and HD2 five-pin connections
Original Tuning Wiki connection map; schematic positions are not connector-face geometry. Source: RACELOGIC HD1 pinouts and HD2 pinouts.

Identify the exact model and hardware generation before wiring. The pin numbers below follow the manufacturer’s numbered connector diagrams; consult the linked drawings for the connector face and orientation, and distinguish the device socket from the mating cable’s wire side. RS232 TX and RX are labelled from the device documentation; check the other device’s direction. Disconnect power while checking continuity and individually insulate unused leads.

VBOX Video HD1 — Hirose power and communications

Schematic wiring paths for VBOX HD1 COM1 power and CAN
Original Tuning Wiki functional wiring illustration for HD1 COM1; not a connector-face view. Based on RACELOGIC's HD1 pinout. Verify the loom and vehicle power before connection.

RACELOGIC’s HD1 pinout lists the same six pin assignments for both power/communications HR30 connectors, with the OLED display supported only on COM1. The separate hardware overview identifies COM1 with CAN 1 and the second power/communications connector with CAN 2, while the pinout page describes both as CAN 1. Confirm the individual bus selection and hardware with RACELOGIC before wiring; the shared pin labels alone do not resolve that documentation conflict.

PinHD1 six-pin Hirose HR30 function
1RS232 RX
2RS232 TX
3Ground
4CAN low
5CAN high
6Power

The same pinout lists the separate three-pin external microphone connector: 1 audio in, 2 mic bias, 3 audio ground. The hardware overview specifies 6–18 V DC supply and separate GNSS antenna and micro-HDMI connections; HDMI output needs an external recorder or streaming encoder for remote video.

For the manufacturer's HD1 installation harness, red is nominal +12 V, blue ground, yellow CAN high and green CAN low. Those colours apply to that harness only; verify the cable supplied. The manufacturer recommends ignition-switched power and cautions against connection to a jump-start lead or charger under load.

VBOX Video HD2 — power and CAN/serial

The HD2 pinout and rear-panel drawing shows separate LEMO connectors. Its two-pin POWER connector has pin 1 power positive and pin 2 ground; chassis is ground. The five-pin CAN/SER connector is a different socket from the five-pin USB connector.

PinHD2 five-pin CAN/SER function
1RS232 TX
2RS232 RX
3CAN high
4CAN low
5+V power output

For completeness, the separate five-pin HD2 USB connector is documented as 1 USB ID, 2 DP, 3 ground, 4 USB 5 V and 5 DM. The two nine-pin camera connectors and four-pin microphone are also shown in the manufacturer’s pinout. Do not assume any HD1, HD Lite or vehicle connector has the HD2 assignment.

RACELOGIC’s HD2 CAN connection guide identifies RLCAB069L for OBD-II, RLCAB015L for bare-wire CAN and RLACS182L for clipping onto a CAN pair; check compatibility with the hardware generation and display arrangement. A physical OBD-II connection does not prove that the desired ECU channels are available: configure the correct CAN bitrate and channel decoding for the vehicle.

Sources and further reading

  1. RACELOGIC: VBOX Motorsport product overview.
  2. RACELOGIC: VBOX Video HD1.
  3. RACELOGIC: VBOX Video HD2.
  4. RACELOGIC: product documentation and version-specific datasheets.
  5. RACELOGIC: VBOX Video HDMI 25 Hz datasheet.
  6. RACELOGIC: VBOX Video HD2 Setup software.