Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Emissions control
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Bosch

For dosing pumps, injectors, supply lines and documented component examples, see AdBlue dosing systems and injectors.

What the reduction does

Selective catalytic reduction treats diesel nitrogen oxides in the exhaust. Bosch describes that reduction as taking place in the presence of oxygen. A urea solution is injected into the exhaust stream. Bosch identifies the urea as (NH2)2CO. Thermolysis and hydrolysis convert it to ammonia. On the catalyst, the ammonia reduces the nitrogen oxides to water and nitrogen. The opened Bosch pages name those steps and do not print balanced equations.

The American Petroleum Institute describes the same chain as heat from the exhaust, the fluid, and a catalyst. The VDA describes ammonia at the SCR catalyst converting nitrogen oxides to nitrogen and water. How the engine forms the nitrogen oxides is on petrol and diesel emissions. Exhaust-gas recirculation is a separate control, on EGR faults. The VDA also names a nitrogen-oxide storage catalyst as the other diesel aftertreatment route.

The fluid

The named fluid is AUS 32. ISO 22241-1 is the quality standard for that aqueous urea solution, for SCR systems on diesel engines. The public ISO catalogue entry states that duty. It does not print the composition figures.

The percentage is stated on other pages. Bosch's Denoxtronic page calls the metered fluid diesel exhaust fluid, an aqueous urea solution of 32.5%. The API calls diesel exhaust fluid a 32.5% solution of technically pure urea in purified water, and names ISO 22241 as the purity standard. A Mabanaft glossary describes AdBlue as 32.5% urea by mass in demineralised water. A Bosch workshop brochure uses a looser phrase: up to 32.5% urea and up to 67.5% demineralised water. Intertek's ISO 22241-1 testing page reproduces a urea-content target of 32.5% by mass, with limits of 31.8% to 33.2%. The opened pages use AdBlue and DEF as names for that AUS 32 solution.

NameWhere it comes fromWhat the opened page says
AUS 32ISO 22241Aqueous urea solution used as the NOx-reduction agent for diesel SCR.
AdBlueVDA trademarkThe VDA's licensed name for AUS 32. Quality is set by ISO 22241-1 to 4.
DEFNorth AmericaMabanaft states this is the North American name. The API certifies it as AUS 32 against ISO 22241.

The VDA says AdBlue is stored in its own tank, close to the diesel tank, and is not added to the diesel. The VDA QMC says fluid that misses ISO 22241 can put the SCR system out of action, and that a container can carry the AdBlue name without a VDA licence.

How Denoxtronic is arranged

Denoxtronic is Bosch's modular dosing system for this fluid. The tank holds the solution. A supply module brings it up to pressure and feeds a dosing module. The dosing module meters it, atomises it, and injects it into the exhaust pipe. Mabanaft places that injection upstream of the SCR catalyst. The dosing control unit calculates the quantity from engine and exhaust-gas data. Bosch describes that calculation as model-based. On the commercial-vehicle diagram that calculation can sit in the dosing control unit or in the engine control unit. Separate dosing controllers are listed on Bosch DCU dosing control.

The supply module on Bosch's current product page is welded to the bottom of the tank. A solenoid membrane pump runs when a dose is required. That version has no return line to the tank, and the system stays pressurised through a start-stop event. One sensor reads level, temperature and concentration. Bosch describes the filter as a lifetime filter. An aftermarket heating-pot kit carries the tank heater, a level sensor and a filter. A supply-module 2.1 drawing also shows a membrane pump, a valve for flow direction, and a control unit that cools the dosing module. Bosch marks that drawing as dependent on the system.

Bosch aftermarket brochures name Denoxtronic 1.1, 2.1, 2.2, 3.1, 5.1, 5.2, 5.3, 6-5 and 6-HD. A second Bosch diesel brochure dates some of those names differently, so the years are left out. For Denoxtronic 5.x on passenger cars and light commercial vehicles, Bosch places the pump under the tank. The pump can be replaced while the supply module and the tank stay fitted.

A commercial-vehicle diagram, given as an example for Denoxtronic 2.2, lists a mixer and an SCR catalyst with an ammonia-slip catalyst. The caption does not describe either job. Bosch's NOx-sensor page puts the sensor upstream of the SCR catalyst, downstream of it, or in both places, depending on the application. It measures nitrogen oxides and oxygen, and the page also includes an ammonia signal. Bosch uses the signals to evaluate the injected quantity and for on-board monitoring. The sensor is connected over CAN. Exhaust-gas temperature sensors in the workshop brochure monitor an optimum range and protect the turbocharger, the catalysts and the particulate filter.

Heat, freezing and crystals

The conversion of urea to ammonia is a hot-exhaust process. Bosch names thermolysis and hydrolysis. The API includes heat from the exhaust in the same description. The workshop brochure says the exhaust-temperature sensors monitor an optimum range for the aftertreatment components. No Bosch page opened for this article states a Celsius temperature at which dosing into the exhaust is allowed to start.

The fluid freezes in the tank. The VDA says it freezes below −11 °C, that freezing does not spoil it, and that it can be used again once it has thawed. Bosch's current supply-module page uses the same −11 °C point and says the tank heater then thaws enough fluid for dosing. The commercial-vehicle workshop brochure says the solution freezes and expands at −11.5 °C, and that compressible elements in the filter and the supply module allow for the expansion. Both temperatures appear on the pages above.

Cold hardware is a separate limit from the exhaust temperature. On the current supply module, turning the ignition off purges the pressure line. Bosch states that this protects the dosing module in a cold condition.

Crystals are a service finding. The workshop brochure says leaked solution creeps, because the viscosity is low, and crystallises in air. The diesel-components brochure says to drain the circuit, wash the parts in water, remove crystalline deposits, fit the filter, and vent the circuit. Those pages locate the crystals in leaked or residual solution. They do not describe spraying into a cold exhaust pipe.

The oxidation catalyst and the filter

Bosch's UK aftermarket page labels one exhaust order: exhaust gas, an oxidation catalyst, a diesel particulate filter, then the SCR catalyst. The Denoxtronic 2.2 drawing lists a coated filter, a mixer and an ammonia-slip catalyst as well. Both illustrations put the oxidation catalyst and the particulate filter ahead of the SCR catalyst. The filter itself, and regeneration, are on diesel particulate filters and DPF regeneration.

Departronic, where it is fitted, meters diesel into the exhaust upstream of the oxidation catalyst so the filter can regenerate. It does not meter the urea solution. Filter loading is a different measurement again. Bosch says a differential-pressure sensor reads the drop across the particulate filter, and a particulate sensor monitors the filter.

What the workshop meets

The level sensor is on the urea circuit, in the supply module or the heating pot. A low-fluid warning is that measurement. The VDA says the tank has to contain fluid: running without it risks damage to the SCR equipment, and the exhaust will not meet the legal limit. Filter loading stays with the pressure and particulate sensors.

Fluid quality reaches the same system. The supply module Bosch describes measures concentration as well as level. The VDA QMC says solution outside ISO 22241 can make the SCR system fail. Intertek records diesel in the urea tank as a known contaminant. The fill is the urea tank. The VDA says the solution is not put into the diesel.

A crystallised dosing path is dried solution in the circuit, washed off with water when the filter is serviced. The NOx sensor is how the control unit watches the catalyst. Upstream and downstream nitrogen-oxide readings, as fitted, and the ammonia signal are there to evaluate the injected quantity and to monitor the SCR system. Soot in the filter is the differential-pressure sensor and the particulate sensor.

PAT fluid is another tank and another job. On engines with a fuel-borne catalyst, that additive is metered into the diesel. AdBlue, DEF and AUS 32 are injected into the exhaust for the SCR catalyst. Both are set out on diesel particulate filters and on PAT fluid and fuel-borne catalysts.

Sources

  • Bosch Mobility: Denoxtronic exhaust-gas treatment. Urea solution of 32.5% called DEF; thermolysis and hydrolysis to ammonia; ammonia reduces nitrogen oxides to nitrogen and water in the presence of oxygen; urea written as (NH2)2CO; supply module, dosing module and model-based dosing in the control unit. Accessed 2026-11-13.
  • Bosch Mobility: Denoxtronic supply module. Solenoid membrane pump welded to the tank bottom; no return line; system stays pressurised in start-stop; purge at ignition-off to protect a cold dosing module; one sensor for level, temperature and concentration; freeze and tank heater below −11 °C. Accessed 2026-11-13.
  • Bosch Mobility: NOx sensor. Sensor upstream and downstream of the SCR catalyst; nitrogen oxides, oxygen and ammonia; used to judge injected AdBlue quantity and for on-board monitoring; CAN. Accessed 2026-11-13.
  • Bosch Aftermarket, UK: diesel systems. Letter order of exhaust gas, oxidation catalyst, particulate filter and SCR catalyst; dosing control unit calculates the quantity from engine and exhaust-gas data; supply module and dosing module; Denoxtronic 5.x pump under the tank, replaceable on its own. Accessed 2026-11-13.
  • Bosch Aftermarket: Denoxtronic brochure for commercial vehicles. Generation names; dosing control unit or engine control unit; up to 32.5% urea and up to 67.5% demineralised water; freeze and expansion at −11.5 °C; leaked solution crystallises in air; Denoxtronic 2.2 diagram listing mixer and ammonia-slip catalyst; exhaust-temperature sensors and the optimum range; differential-pressure sensor for filter loading; particulate sensor for the filter. Accessed 2026-11-13.
  • Bosch Aftermarket: diesel system components brochure. Heating pot with heater, level sensor and filter; crystalline deposits washed off with water at a filter change; Departronic meters diesel ahead of the oxidation catalyst; a second, conflicting set of Denoxtronic introduction years. Accessed 2026-11-13.
  • VDA: AdBlue. Trademark for AUS 32; ISO 22241-1 to 4; own tank and not added to diesel; ammonia converts nitrogen oxides to nitrogen and water; storage catalyst named as the other route; freezes below −11 °C and is usable after thawing; running without fluid risks the SCR equipment and the emissions result. Accessed 2026-11-13.
  • VDA QMC: AdBlue auditing. Fluid outside ISO 22241 can cause SCR failure; the trademark can appear without a VDA licence. Accessed 2026-11-13.
  • ISO 22241-1:2019 catalogue entry. AUS 32 is the aqueous urea solution specified for diesel SCR. The catalogue page does not publish the percentage. Accessed 2026-11-13.
  • API: diesel exhaust fluid. DEF, also called AUS 32, is a 32.5% solution of technically pure urea in purified water; heat, fluid and catalyst; ISO 22241 certification. Accessed 2026-11-13.
  • Mabanaft: AdBlue glossary. 32.5% urea by mass in demineralised water; DEF as the North American name; injection upstream of the SCR catalyst; conversion to ammonia. Accessed 2026-11-13.
  • Intertek: ISO 22241-1 testing page. Reproduced urea-content target of 32.5% by mass and limits 31.8% to 33.2%; diesel noted as a contaminant of the urea tank. Accessed 2026-11-13.