Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Gearboxes
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Citroën, Peugeot

Changes from revision 3 to revision 5

Removed text is struck through; added text is highlighted.

Sensodrive is a five-speed MA manual gearbox with the clutch and the gear lever driven by electric motors. There is no clutch pedal and no mechanical gear linkage. The driver can leave the shifts to the ECU or take them with the selector and the steering-wheel paddles. The engine starts only with the brake pressed. It was used on the C2, C3 and C3 Pluriel, on the TU, ET3 and DV4 engines of those cars. The gearbox oil is filled for life. The clutch is the part whose temperature the ECU estimates.

A dedicated engine ECU talks to the gearbox ECU. That link is what allows a shift without lifting the accelerator: the engine ECU sets engine speed and cuts torque while the clutch is open. The gearbox ECU is Flash and is updated by download. The injection ECU is updated whenever the gearbox ECU is updated, and the other way round.

Actuators

The clutch actuator, 1665, is bolted to a bracket that also carries the ECU on rubber spacers. The bracket is four bolts to the gearbox, and the actuator is three bolts to the bracket. Inside an aluminium housing are a DC motor with two Hall sensors, a toothed segment, a compensating spring, a wear adjuster and a thrust-bearing tensioner. The clutch is a pushed type. Open and closed are both stable, and the motor is not powered to hold either of them.

To open, the ECU drives the motor, the wear adjuster locks, and the fork moves the thrust bearing. Declutch travel is about 20 mm whatever the wear. At the end of the segment travel the compensating spring helps the motor, and the motor is then switched off. Closing reverses the motor. With the clutch closed the adjuster unlocks and can shorten as the plate wears, so fork travel stays in the range the ECU has learnt. The adjuster is not repairable. The ECU has to have memorised total fork travel and the biting point.

The gearbox actuator engages each gear by lifting and then rotating the internal lever. Two motors share one housing and are not removable separately: gear-changing actuator 1663 and gear-selection actuator 1664. They never run at the same time. The three selection heights are about 5 to 7 mm apart, and the three rotational positions are about 17° to 20° apart. A ramp selects and engages together to save time.

A shift runs through preload in position, unmeshing, synchronisation, meshing and a confirmation of mesh, all under force and speed, then a retraction under current so the dog teeth are not left loaded. Once meshing has started, the ECU finishes the retraction before it will begin another shift. If a gear is hard to engage, the ECU tries twice more. Stationary, it opens and closes the clutch to help. After three failed attempts that gear is disabled and a fault is stored.

All three motors are direct current, controlled by a variable voltage. Resistance of each motor, measured on its two power pins, is about 2 ohms. The Hall sensors are supplied at 5 V, give a 0 to 5 V square wave, and produce 60 pulses per revolution.

The input-speed sensor, 1662, is a magnetic pickup facing the teeth of 2nd gear on the primary shaft. Resistance between its two pins is about 800 ohms. The wire is not shielded, so the harness route matters. The ECU uses it to see clutch slip against engine speed, to find the biting point, to close the clutch, and to see the end of synchronisation.

How a shift feels

The same phases run in automatic and in sequential. At the start the gearbox ECU tells the network that a shift is in progress and forbids a change of air-conditioning compressor state. The driver’s accelerator request is ignored and the clutch is still closed. As the clutch opens, the maximum torque the gearbox will allow is sent to the engine ECU and is updated continuously, and the engine ECU brings torque to 0 N·m by the time the clutch is open. With the clutch open, the gearbox ECU requests engine-speed regulation and moves that speed setting towards the speed that matches the gear being engaged and the road speed. The actuator does the shift in this phase. Another gear can still be requested until synchronisation of the current gear has started. Once synchronisation has started, the shift runs on to the end. The clutch then closes at one of three speeds, from the slowest and most comfortable to the fastest and most sporting, chosen from the driving style. Allowed torque rises with the clutch until it matches what the driver is asking, and the accelerator request is obeyed again.

In normal running the ECU relearns the biting point and the position where synchronisation starts, and it takes the age of the gearbox into account.

Driver controls and the laws

The left paddle is downshift and the right paddle is upshift. Paddles cannot select neutral or reverse. The selector is short-stroke and only the centre is stable: “+” up, “−” down, N and R. Between selector commands the lever has to pass through the centre. Between paddle commands the paddle has to be released. Opposite commands, a held selector or a held paddle are ignored until they are released. At every ignition-on the program is automatic. Using “+” or “−” in automatic also selects sequential and does that shift. The program button swaps between automatic and sequential, including while the car is moving. Snow is selected when wheel slip is detected, by the ESP ECU, or by the gearbox ECU from the four wheel speeds on a car that has ABS and no ESP. When slip stops, the law that was active before slip returns.

The gear and the program go from the gearbox ECU to the BSI, and the BSI repeats them to the instrument panel. Auto lit means automatic. Auto out means sequential. Snow lit means the snow law is active. A fault flashes auto and snow together and puts a dash on the gear display.

Nine laws are stored or calculated. Six are the adaptive references: L1 economy, L2 medium, L3 sport, L4 gentle slope, L5 steep slope and L6 downhill. L7 is snow. Intermediate laws between those references are calculated from the last few minutes of driving. A warm-up law runs for a time that depends on the engine, then drops out. A further law is reserved for the downgraded modes. Upshift and downshift thresholds are separated so the gearbox does not hunt. One example, at 80 percent accelerator, changes 3rd to 4th at 100 km/h and 4th back to 3rd below 72 km/h. That example is a shape of law, and every calibration does not use those speeds.

A fast lift blocks the upshift so engine braking remains, including in a corner seen from the wheel speeds, and downhill with the accelerator released. A fast press in automatic briefly raises sportiness, and lifting returns to the previous law at once. Braking downshifts can be forced, and in some cases the ECU makes a triple downshift. Kick-down delays the upshift and downshifts if the speed conditions are met. In snow, pull-away is in 2nd, shifts are less frequent, wheel torque is kept gentle, braking forces a downshift, and a kick-down downshift is allowed only below 15 km/h.

In sequential an impossible request is ignored. At maximum engine speed the ECU selects a higher gear and stays in sequential. If engine speed is too low it selects a lower gear, and if speed is still too low it opens the clutch to avoid a stall. Neutral can be engaged while moving, and the next “+” or “−” then picks a gear that fits the road speed. With the car parked and the engine off, 1st, 2nd, N and R can be engaged once the panel is active, but only one change is authorised in that state. A gear cannot be deselected with the ignition off.

After three minutes stationary with the engine running and a gear engaged, the ECU selects N. Pressing the accelerator engages 1st only if the stop has not already exceeded two minutes.

The ECU estimates clutch-plate temperature. Holding the car on a hill with the accelerator heats the clutch. When it is too hot the ECU cycles the clutch so the car oscillates until the engine stalls. The handbrake is how the car is held. The protection is that behaviour. No temperature figure is given.

What a command does

In the table, A means automatic remains or is selected, and M means the result is sequential. A single symbol is one action. A double symbol is two successive actions. Automatic, gear selector:

Engaged+−NR++−− RA, 1stnoneA, NnoneA, RA, R NA, 1stnonenoneA, RM, 2ndM, N 1M, 2ndM, 1stA, NA, RM, 3rdM, 1st 2M, 3rdM, 1stA, NA, RM, 4thM, 1st 3M, 4thM, 2ndA, NA, RM, 5thM, 1st 4M, 5thM, 3rdA, NA, RM, 5thM, 2nd 5M, 5thM, 4thA, NA, RM, 5thM, 3rd

Paddles have no N or R command. From N, “+” selects sequential and 1st. From 5th, “+” does nothing and “−” selects sequential and 4th. From R, the paddles do nothing. In sequential the same shifts happen and the program stays sequential. The program button swaps program and leaves the engaged gear where it is. Reverse is engaged only with the brake pressed and the car stationary. First is engaged from a “+” with the engine near idle.

A later software changes the automatic behaviour. With AUTO still displayed, a paddle or lever request is carried out at once, inside the under-rev and over-rev limits, and the gearbox returns to automatic after a time that depends on how the car is being used, or if the driver kick-downs. Permanent manual is the AUTO button. Return to automatic is the button, or ignition off. On a car below RP 10080 a paddle touch no longer leaves the car in manual for the rest of the journey, and that is explained when the car is handed back.

Starting, wake-up and the network

Unlocking the doors or opening the driver’s door runs a rapid initialisation of both actuators, switches the display on and opens the clutch if N is engaged. The ECU sleeps four minutes after the instrument panel goes off.

A full position initialisation, 10 seconds to 1 minute, runs with the ignition on and the brake pressed if the battery was disconnected before the panel went off or before the ECU slept, or if a programming operation failed. The engine is not allowed to crank during it. If programming has never been completed, this initialisation runs on every start attempt.

With 1st, 2nd or R engaged, the brake opens the clutch and cranking is allowed. Releasing the brake before the engine has started closes the clutch and cranking is refused. The starter-prohibition relay, 1005, is energised by an earth from the ECU, and only when the key is at crank, the actuators are in a start position and the brake is pressed. The relay is at the front of the left wheel arch, behind the left headlamp. On its black 9-way plug, pin 2 feeds the starter, pin 4 is 12 V from the engine relay unit, pin 5 is crank, and pin 9 is the earth from the gearbox ECU. A battery fault is stored above 16 V and below 8 V.

The ECU has a green 48-way connector and a blue 32-way connector. Permanent battery is on the green connector at L1, M1 and M2. Ignition-on is A2, crank is D4, the starter relay is B3, the driver’s door is E3, the stop switch is F3, and the K-line is H4. CAN high is J1 and CAN low is J2. Selector signals are C1, C2, E4 and H3, with the selector earth on J4. Paddles are J3 and K3, with paddle earth on K4. The program button is A4. Power earths are L3, L4 and M4.

On the blue connector the input-speed sensor is A1 and B1. The clutch motor is H2 and H3. The gear-changing motor is H1 and G1. The selection motor is H4 and G4. Two selection-actuator position inputs are listed, on C4 and D4.

Gear, program and fault information is sent on VAN and on CAN. On CAN the engine ECU receives the speed-regulation request, the speed setting, the torque reduction, the maximum torque the gearbox will allow, the compressor lock and the gear engaged. It returns engine torque, engine speed, coolant temperature, throttle position, the idle setting, the torque the driver asked for, actual torque and resistant torque. The ABS or ESP ECU provides vehicle speed, permission to shift, and whether regulation is in progress or faulty. Two brake switches are compared: a closing switch wired to the ECU, and a second switch the BSI puts on CAN.

Selector and paddle voltages

The selector has four signal wires, supplied by the ECU, and the ECU checks that the combination is coherent. Voltages are bands, measured between the electronic earth (connector pin 3, not body earth) and the signal pin. The high band is 2.4 to 4.1 V and the low band is 0.6 to 2.4 V.

PositionA1A2A3A4 Centrehighhighhighhigh +lowlowhighhigh −lowhighlowhigh Nlowhighhighlow Rhighhighlowlow

The paddles use the same two bands. Both released is high on both. The downshift paddle pressed pulls its channel low. Both pressed is low on both. The program button selects by an earth on its signal wire, and only while the button is held.

Diagnostic parameters include clutch state (slipping, clutched, declutched, synchronised), the selector position, both paddles, input speed and engine speed to 7,000 rpm, vehicle speed from the ABS ECU to 200 km/h, accelerator 0 to 100 percent, and coolant from −48 °C to 142.5 °C. Engine torque is shown both as the value from the engine ECU and as the value the gearbox ECU has calculated, over 10 to 40.8 m·daN.

Programming

Position initialisation at start-up is separate from programming. Programming stores the actuator, clutch and gate characteristics, and it is started with the diagnostic tool. The clutch actuator is always programmed before the gearbox actuator. Until programming has been done, the tool ignores actuator commands, and the start-up initialisation runs on every attempt.

Clutch end positions are learnt engine-off, car level, ignition on. The ECU opens the clutch and closes it, in about 2 seconds. The biting point is learnt with the engine idling, in N, handbrake on. The ECU makes a series of partial movements and watches the input-speed sensor for the first rotation of the primary shaft, in about 10 seconds. One replacement job allows up to 1 minute for the whole clutch-actuator program.

From diagnostic CD 32 the bite-point learn can report a false error. The manual sequence is: declutch, clutch, then the bite-point routine, end the diagnostic session and disconnect, ignition off, ignition on, select neutral, start, and with the brake held select 1st then neutral ten times, waiting 5 seconds in each neutral, then ignition off.

Gate learning is engine-off, handbrake off, car level, battery at or above 12.5 V. If voltage falls below 10.5 V the programming fails. A charger in parallel is allowed. The ignition is on and the clutch is open. One limit is 8 minutes. The job tables allow 12 minutes after refitting the actuator and 13 minutes for a gearbox refit or a clutch replacement that runs the combined sequence. The longer figure is the one the job was planned around. Afterwards the ignition is switched off, the panel is allowed to go out, and 4 minutes pass before the ignition is switched on again, so the values are stored. The same wait follows clutch programming.

The tool offers clutch only, gearbox only, and a combined sequence that does clutch ends, biting point, clutch opening, then the gate. Clutch-only asks for battery voltage above 12 V, which is a lower bar than the 12.5 V of the gate and the combined sequence.

Program the clutch after the clutch actuator is refitted, after a new clutch and after the road test, or when the ECU is replaced. Program the gate after the gearbox actuator is refitted, the gearbox is replaced, or the ECU is replaced. The combined sequence follows a gearbox refit and can replace the two separate programs after a download.

Counters are read and written, and reset when the related part is replaced. Clutch energy is stored as three levels and a total. Gear engagements are counted for 1st through 5th and reverse. Selector and paddle counts are separate. Replacing the steering-wheel controls is the reason to reset the paddle counter. On ECU replacement the counters are copied across before the combined program. Two Sensodrive ECUs are not swapped between cars. Moving one requires both programming operations on the car it is fitted to, or the actuators can be damaged. A new ECU needs no configuration.

The clutch specification is kept. A clutch of another make or with different characteristics makes the system malfunction. A mechanism that has been dropped is not fitted. Actuator tests produce high force at high speed. An actuator that has been removed is not commanded, except the assembly-position command, or it will be damaged. The fork and the internal lever are not moved by hand. Opening the driver’s door or switching the ignition on makes both actuators initialise, so the fork moves. To tow, N is engaged with the selector and confirmed on the display.

Evidence after a failed learn-in: Reproduced Citroën C3 I MA workshop information says an unsuccessful initialisation is recorded as a gearbox fault and directs the technician to note the diagnostic report and address the fault. It also describes stored context such as battery voltage, clutch and selected-gear state, input and vehicle speeds, and whether a shift was in progress. Capture these before clearing faults or attempting setup again. The document also directs checking the engine ECU fault memory when a piloted-gearbox defect is signalled. This is a C3 I example; use the current vehicle-specific service procedure and do not assume an unsuccessful initialisation identifies a defective actuator.

Downgraded behaviour

A fault flashes the auto and snow lamps and shows a dash, except where a row says the lamps stay off.

FaultBehaviour Programming incompleteActuators initialise at ignition-on with the brake pressed. The engine cannot crank during that. A gear jumps out, or will not engage after three attemptsThat gear is prohibited and another is selected. A gear will not disengageThe engaged gear is kept while driving. In 3rd, 4th or 5th, the ECU declutches at a stop and the car cannot be driven. In R, 1st or 2nd, driving is still allowed. ECU supplyNo gearbox operation. ECU output stage, RAM or ROMActuators are no longer controlled. Driving is impossible. Clutch or gear-changing position-sensor supplyDriving continues with reduced comfort. Selection position signalOpen-loop is tried. If a shift is still possible, sequential is selected, shifts are limited and double or triple shifts are dropped. If it is not, the gear is kept and N is engaged at a stop. Clutch position signalThe same open-loop trial. If the clutch can still be opened and closed, sequential is selected and shifts are limited. If it cannot, N is engaged at a stop and driving is impossible. Selector signalThe selector is deactivated. Lamps flash only after automatic has been selected. N and R can be selected with the paddles. If neither control works, automatic is selected. Paddle signalPaddles deactivated, with the same fallback. Input speedLamps do not flash. Wheel speed is used instead. Shift time increases. Power-latchLamps do not flash. The ECU stays awake and can flatten the battery. Disconnecting the battery during the power-latch stores a fault. Gear-changing motorThe gear is kept while driving. At a stop the clutch is opened. Clutch faultLamps do not flash. The number of shifts is reduced.

Remote faults are a loss of information from the engine ECU, the ABS ECU or the BSI, and a CAN fault. Each stored fault also keeps battery voltage, clutch status, the gear, input speed, vehicle speed, key position, whether a shift was in progress, engine speed and coolant temperature.

Software and the cars it was fitted to

A car that locks in reverse, or will not select a forward gear, is checked for injection parameters and for gearbox-actuator position before the gearbox is stripped. The correction is a gearbox software update, and the actuator is reset if the position is wrong.

After that software, the gear and AUTO symbols can flash on a gearbox that is working. The cause is ignition off while the car was still moving, even slowly, with the engine not restarted within 5 minutes. The display is resynchronised by starting, driving a short distance, stopping, waiting 5 minutes with the ignition off, and restarting. A later software removes that strategy.

Failure to select 1st or reverse is a selection-gate offset learnt wrongly at initialisation. The correction is the D4 download. Before D4 on a TU5JP4, the injection software is already the latest available. Identities are supplier 04, system 00, application 01, edition C201.

CarEngineVersion C2TU3JPE7 C2TU5JP4EA C2DV4TD 150 N·mE8 C2DV4TD 160 N·mEB C3TU5JP4 up to RP 9639E1 C3TU5JP4 from RP 9640E2 C3DV4TD 150 N·mE3 C3DV4TD 160 N·mE9 C3ET3J4EE PlurielTU5JP4 up to RP 9639E5 PlurielTU5JP4 from RP 9640E6

One oblong actuator fixing hole was later replaced by a round 9.3 mm hole for the 8 mm screw, so the actuator sits with less offset on the gates.

BSI software 39.1 is incompatible with some Sensodrive ECUs. Those gearbox ECUs are replaced before 39.1 is downloaded. DV4TD Sensodrive software was compatible. The incompatible references are 9651497480, 9651497380 and 9652762680 on Pluriel up to the OPR 9639/9640 break, 9652762280 on C2 TU3JP, 9652762580 on C2 TU5JP4, 9651497280 on C3 TU5JP4 up to OPR 9639, 9650922180 and 9652762780 on C3 TU5JP4 from OPR 9640, and 9651933780 on C3 ET3.

Check the fault description before acting: A reproduced C3 I facelift MA piloted-manual fault-code table describes P1755 as a clutch-actuator coherence fault and P1804 as activated clutch-actuator thermal protection. This contradicts an earlier description on this page that called P1755 thermal protection and attributed skipped gears to lost learned values. Do not diagnose the component, reset adaptations or apply a software download solely from the code: capture its full manufacturer description and other faults, and use the applicable vehicle and controller test plan. The linked reproduction is in Chinese; verify the exact model and current service information.Historical notes identify D4.4 with CAN-VAN and N2.3 with full CAN, and say P1704 brake-signal coherence is no longer used from those software versions. Treat those statements as historical leads, not verified current programming instructions; confirm software applicability and any required repair with Citroën for the individual vehicle.A gearbox that skips gears and stores P1755 has lost its learnt values. P1755 here is clutch thermal protection. The download is by architecture: D4.4 on CAN-VAN, N2.3 on full CAN. From these softwares, P1704 (brake-signal coherence) is no longer used, and P1804 is clutch-actuator thermal protection.

N2.3 references: C3 TU5JP4 9661418580, C3 ET3J4 9661418480, C3 DV4TD 9661418280, Pluriel TU5JP4 9661418780, C2 TU3A 9661419180, C2 TU5JP4 9661419280, C2 ET3J4 9661419080, C2 DV4TD 160 N·m 9661418880. The ET3J4 files are also valid for the stop-start STT2. D4.4 is a separate reference list, split by ADR and NDR and, on the Pluriel, by whether the clutch lining is chlorinated. The reference follows the car’s equipment. The two families are not interchangeable.

The MA gearbox under the actuators has its own mechanical faults, shared with the manual MA. A loose crown wheel, a manufacturing fault of April 2003, loses drive and was seen especially on C3 DV4TD driving-school cars, and it is possible on Pluriel, Saxo, Xsara and every Sensodrive. A primary-shaft bearing that starts as a noise around 50,000 miles on late-2003 and 2004 cars, DV4 excluded, will destroy the gearbox. The shaft and the bearings are replaced. A bell-housing leak on boxes built from October 2004 to January 2005 is a badly machined primary-shaft sealing face. The seal tube and the primary shaft are replaced. Any job that removes the gearbox greases the primary-shaft splines with Molykote G Rapid Plus, grease 998405.

For comparisons with other manufacturers’ systems, see BMW SMG, Ferrari F1, Maserati Cambiocorsa and Fiat systems and automated manual clutch and gearshift control. Each system has its own service and diagnostic procedures.

For separate city-car examples, see Peugeot 108 and Citroën C1 ETG operation and diagnosis. The handbook examples do not establish interchangeable actuator, fluid or learning procedures with this gearbox.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 3: Sensodrive MA gearbox

Sensodrive is a five-speed MA manual gearbox with the clutch and the gear lever driven by electric motors. There is no clutch pedal and no mechanical gear linkage. The driver can leave the shifts to the ECU or take them with the selector and the steering-wheel paddles. The engine starts only with the brake pressed. It was used on the C2, C3 and C3 Pluriel, on the TU, ET3 and DV4 engines of those cars. The gearbox oil is filled for life. The clutch is the part whose temperature the ECU estimates.

A dedicated engine ECU talks to the gearbox ECU. That link is what allows a shift without lifting the accelerator: the engine ECU sets engine speed and cuts torque while the clutch is open. The gearbox ECU is Flash and is updated by download. The injection ECU is updated whenever the gearbox ECU is updated, and the other way round.

Actuators

The clutch actuator, 1665, is bolted to a bracket that also carries the ECU on rubber spacers. The bracket is four bolts to the gearbox, and the actuator is three bolts to the bracket. Inside an aluminium housing are a DC motor with two Hall sensors, a toothed segment, a compensating spring, a wear adjuster and a thrust-bearing tensioner. The clutch is a pushed type. Open and closed are both stable, and the motor is not powered to hold either of them.

To open, the ECU drives the motor, the wear adjuster locks, and the fork moves the thrust bearing. Declutch travel is about 20 mm whatever the wear. At the end of the segment travel the compensating spring helps the motor, and the motor is then switched off. Closing reverses the motor. With the clutch closed the adjuster unlocks and can shorten as the plate wears, so fork travel stays in the range the ECU has learnt. The adjuster is not repairable. The ECU has to have memorised total fork travel and the biting point.

The gearbox actuator engages each gear by lifting and then rotating the internal lever. Two motors share one housing and are not removable separately: gear-changing actuator 1663 and gear-selection actuator 1664. They never run at the same time. The three selection heights are about 5 to 7 mm apart, and the three rotational positions are about 17° to 20° apart. A ramp selects and engages together to save time.

A shift runs through preload in position, unmeshing, synchronisation, meshing and a confirmation of mesh, all under force and speed, then a retraction under current so the dog teeth are not left loaded. Once meshing has started, the ECU finishes the retraction before it will begin another shift. If a gear is hard to engage, the ECU tries twice more. Stationary, it opens and closes the clutch to help. After three failed attempts that gear is disabled and a fault is stored.

All three motors are direct current, controlled by a variable voltage. Resistance of each motor, measured on its two power pins, is about 2 ohms. The Hall sensors are supplied at 5 V, give a 0 to 5 V square wave, and produce 60 pulses per revolution.

The input-speed sensor, 1662, is a magnetic pickup facing the teeth of 2nd gear on the primary shaft. Resistance between its two pins is about 800 ohms. The wire is not shielded, so the harness route matters. The ECU uses it to see clutch slip against engine speed, to find the biting point, to close the clutch, and to see the end of synchronisation.

How a shift feels

The same phases run in automatic and in sequential. At the start the gearbox ECU tells the network that a shift is in progress and forbids a change of air-conditioning compressor state. The driver’s accelerator request is ignored and the clutch is still closed. As the clutch opens, the maximum torque the gearbox will allow is sent to the engine ECU and is updated continuously, and the engine ECU brings torque to 0 N·m by the time the clutch is open. With the clutch open, the gearbox ECU requests engine-speed regulation and moves that speed setting towards the speed that matches the gear being engaged and the road speed. The actuator does the shift in this phase. Another gear can still be requested until synchronisation of the current gear has started. Once synchronisation has started, the shift runs on to the end. The clutch then closes at one of three speeds, from the slowest and most comfortable to the fastest and most sporting, chosen from the driving style. Allowed torque rises with the clutch until it matches what the driver is asking, and the accelerator request is obeyed again.

In normal running the ECU relearns the biting point and the position where synchronisation starts, and it takes the age of the gearbox into account.

Driver controls and the laws

The left paddle is downshift and the right paddle is upshift. Paddles cannot select neutral or reverse. The selector is short-stroke and only the centre is stable: “+” up, “−” down, N and R. Between selector commands the lever has to pass through the centre. Between paddle commands the paddle has to be released. Opposite commands, a held selector or a held paddle are ignored until they are released. At every ignition-on the program is automatic. Using “+” or “−” in automatic also selects sequential and does that shift. The program button swaps between automatic and sequential, including while the car is moving. Snow is selected when wheel slip is detected, by the ESP ECU, or by the gearbox ECU from the four wheel speeds on a car that has ABS and no ESP. When slip stops, the law that was active before slip returns.

The gear and the program go from the gearbox ECU to the BSI, and the BSI repeats them to the instrument panel. Auto lit means automatic. Auto out means sequential. Snow lit means the snow law is active. A fault flashes auto and snow together and puts a dash on the gear display.

Nine laws are stored or calculated. Six are the adaptive references: L1 economy, L2 medium, L3 sport, L4 gentle slope, L5 steep slope and L6 downhill. L7 is snow. Intermediate laws between those references are calculated from the last few minutes of driving. A warm-up law runs for a time that depends on the engine, then drops out. A further law is reserved for the downgraded modes. Upshift and downshift thresholds are separated so the gearbox does not hunt. One example, at 80 percent accelerator, changes 3rd to 4th at 100 km/h and 4th back to 3rd below 72 km/h. That example is a shape of law, and every calibration does not use those speeds.

A fast lift blocks the upshift so engine braking remains, including in a corner seen from the wheel speeds, and downhill with the accelerator released. A fast press in automatic briefly raises sportiness, and lifting returns to the previous law at once. Braking downshifts can be forced, and in some cases the ECU makes a triple downshift. Kick-down delays the upshift and downshifts if the speed conditions are met. In snow, pull-away is in 2nd, shifts are less frequent, wheel torque is kept gentle, braking forces a downshift, and a kick-down downshift is allowed only below 15 km/h.

In sequential an impossible request is ignored. At maximum engine speed the ECU selects a higher gear and stays in sequential. If engine speed is too low it selects a lower gear, and if speed is still too low it opens the clutch to avoid a stall. Neutral can be engaged while moving, and the next “+” or “−” then picks a gear that fits the road speed. With the car parked and the engine off, 1st, 2nd, N and R can be engaged once the panel is active, but only one change is authorised in that state. A gear cannot be deselected with the ignition off.

After three minutes stationary with the engine running and a gear engaged, the ECU selects N. Pressing the accelerator engages 1st only if the stop has not already exceeded two minutes.

The ECU estimates clutch-plate temperature. Holding the car on a hill with the accelerator heats the clutch. When it is too hot the ECU cycles the clutch so the car oscillates until the engine stalls. The handbrake is how the car is held. The protection is that behaviour. No temperature figure is given.

What a command does

In the table, A means automatic remains or is selected, and M means the result is sequential. A single symbol is one action. A double symbol is two successive actions. Automatic, gear selector:

Engaged+−NR++−−
RA, 1stnoneA, NnoneA, RA, R
NA, 1stnonenoneA, RM, 2ndM, N
1M, 2ndM, 1stA, NA, RM, 3rdM, 1st
2M, 3rdM, 1stA, NA, RM, 4thM, 1st
3M, 4thM, 2ndA, NA, RM, 5thM, 1st
4M, 5thM, 3rdA, NA, RM, 5thM, 2nd
5M, 5thM, 4thA, NA, RM, 5thM, 3rd

Paddles have no N or R command. From N, “+” selects sequential and 1st. From 5th, “+” does nothing and “−” selects sequential and 4th. From R, the paddles do nothing. In sequential the same shifts happen and the program stays sequential. The program button swaps program and leaves the engaged gear where it is. Reverse is engaged only with the brake pressed and the car stationary. First is engaged from a “+” with the engine near idle.

A later software changes the automatic behaviour. With AUTO still displayed, a paddle or lever request is carried out at once, inside the under-rev and over-rev limits, and the gearbox returns to automatic after a time that depends on how the car is being used, or if the driver kick-downs. Permanent manual is the AUTO button. Return to automatic is the button, or ignition off. On a car below RP 10080 a paddle touch no longer leaves the car in manual for the rest of the journey, and that is explained when the car is handed back.

Starting, wake-up and the network

Unlocking the doors or opening the driver’s door runs a rapid initialisation of both actuators, switches the display on and opens the clutch if N is engaged. The ECU sleeps four minutes after the instrument panel goes off.

A full position initialisation, 10 seconds to 1 minute, runs with the ignition on and the brake pressed if the battery was disconnected before the panel went off or before the ECU slept, or if a programming operation failed. The engine is not allowed to crank during it. If programming has never been completed, this initialisation runs on every start attempt.

With 1st, 2nd or R engaged, the brake opens the clutch and cranking is allowed. Releasing the brake before the engine has started closes the clutch and cranking is refused. The starter-prohibition relay, 1005, is energised by an earth from the ECU, and only when the key is at crank, the actuators are in a start position and the brake is pressed. The relay is at the front of the left wheel arch, behind the left headlamp. On its black 9-way plug, pin 2 feeds the starter, pin 4 is 12 V from the engine relay unit, pin 5 is crank, and pin 9 is the earth from the gearbox ECU. A battery fault is stored above 16 V and below 8 V.

The ECU has a green 48-way connector and a blue 32-way connector. Permanent battery is on the green connector at L1, M1 and M2. Ignition-on is A2, crank is D4, the starter relay is B3, the driver’s door is E3, the stop switch is F3, and the K-line is H4. CAN high is J1 and CAN low is J2. Selector signals are C1, C2, E4 and H3, with the selector earth on J4. Paddles are J3 and K3, with paddle earth on K4. The program button is A4. Power earths are L3, L4 and M4.

On the blue connector the input-speed sensor is A1 and B1. The clutch motor is H2 and H3. The gear-changing motor is H1 and G1. The selection motor is H4 and G4. Two selection-actuator position inputs are listed, on C4 and D4.

Gear, program and fault information is sent on VAN and on CAN. On CAN the engine ECU receives the speed-regulation request, the speed setting, the torque reduction, the maximum torque the gearbox will allow, the compressor lock and the gear engaged. It returns engine torque, engine speed, coolant temperature, throttle position, the idle setting, the torque the driver asked for, actual torque and resistant torque. The ABS or ESP ECU provides vehicle speed, permission to shift, and whether regulation is in progress or faulty. Two brake switches are compared: a closing switch wired to the ECU, and a second switch the BSI puts on CAN.

Selector and paddle voltages

The selector has four signal wires, supplied by the ECU, and the ECU checks that the combination is coherent. Voltages are bands, measured between the electronic earth (connector pin 3, not body earth) and the signal pin. The high band is 2.4 to 4.1 V and the low band is 0.6 to 2.4 V.

PositionA1A2A3A4
Centrehighhighhighhigh
+lowlowhighhigh
−lowhighlowhigh
Nlowhighhighlow
Rhighhighlowlow

The paddles use the same two bands. Both released is high on both. The downshift paddle pressed pulls its channel low. Both pressed is low on both. The program button selects by an earth on its signal wire, and only while the button is held.

Diagnostic parameters include clutch state (slipping, clutched, declutched, synchronised), the selector position, both paddles, input speed and engine speed to 7,000 rpm, vehicle speed from the ABS ECU to 200 km/h, accelerator 0 to 100 percent, and coolant from −48 °C to 142.5 °C. Engine torque is shown both as the value from the engine ECU and as the value the gearbox ECU has calculated, over 10 to 40.8 m·daN.

Programming

Position initialisation at start-up is separate from programming. Programming stores the actuator, clutch and gate characteristics, and it is started with the diagnostic tool. The clutch actuator is always programmed before the gearbox actuator. Until programming has been done, the tool ignores actuator commands, and the start-up initialisation runs on every attempt.

Clutch end positions are learnt engine-off, car level, ignition on. The ECU opens the clutch and closes it, in about 2 seconds. The biting point is learnt with the engine idling, in N, handbrake on. The ECU makes a series of partial movements and watches the input-speed sensor for the first rotation of the primary shaft, in about 10 seconds. One replacement job allows up to 1 minute for the whole clutch-actuator program.

From diagnostic CD 32 the bite-point learn can report a false error. The manual sequence is: declutch, clutch, then the bite-point routine, end the diagnostic session and disconnect, ignition off, ignition on, select neutral, start, and with the brake held select 1st then neutral ten times, waiting 5 seconds in each neutral, then ignition off.

Gate learning is engine-off, handbrake off, car level, battery at or above 12.5 V. If voltage falls below 10.5 V the programming fails. A charger in parallel is allowed. The ignition is on and the clutch is open. One limit is 8 minutes. The job tables allow 12 minutes after refitting the actuator and 13 minutes for a gearbox refit or a clutch replacement that runs the combined sequence. The longer figure is the one the job was planned around. Afterwards the ignition is switched off, the panel is allowed to go out, and 4 minutes pass before the ignition is switched on again, so the values are stored. The same wait follows clutch programming.

The tool offers clutch only, gearbox only, and a combined sequence that does clutch ends, biting point, clutch opening, then the gate. Clutch-only asks for battery voltage above 12 V, which is a lower bar than the 12.5 V of the gate and the combined sequence.

Program the clutch after the clutch actuator is refitted, after a new clutch and after the road test, or when the ECU is replaced. Program the gate after the gearbox actuator is refitted, the gearbox is replaced, or the ECU is replaced. The combined sequence follows a gearbox refit and can replace the two separate programs after a download.

Counters are read and written, and reset when the related part is replaced. Clutch energy is stored as three levels and a total. Gear engagements are counted for 1st through 5th and reverse. Selector and paddle counts are separate. Replacing the steering-wheel controls is the reason to reset the paddle counter. On ECU replacement the counters are copied across before the combined program. Two Sensodrive ECUs are not swapped between cars. Moving one requires both programming operations on the car it is fitted to, or the actuators can be damaged. A new ECU needs no configuration.

The clutch specification is kept. A clutch of another make or with different characteristics makes the system malfunction. A mechanism that has been dropped is not fitted. Actuator tests produce high force at high speed. An actuator that has been removed is not commanded, except the assembly-position command, or it will be damaged. The fork and the internal lever are not moved by hand. Opening the driver’s door or switching the ignition on makes both actuators initialise, so the fork moves. To tow, N is engaged with the selector and confirmed on the display.

Downgraded behaviour

A fault flashes the auto and snow lamps and shows a dash, except where a row says the lamps stay off.

FaultBehaviour
Programming incompleteActuators initialise at ignition-on with the brake pressed. The engine cannot crank during that.
A gear jumps out, or will not engage after three attemptsThat gear is prohibited and another is selected.
A gear will not disengageThe engaged gear is kept while driving. In 3rd, 4th or 5th, the ECU declutches at a stop and the car cannot be driven. In R, 1st or 2nd, driving is still allowed.
ECU supplyNo gearbox operation.
ECU output stage, RAM or ROMActuators are no longer controlled. Driving is impossible.
Clutch or gear-changing position-sensor supplyDriving continues with reduced comfort.
Selection position signalOpen-loop is tried. If a shift is still possible, sequential is selected, shifts are limited and double or triple shifts are dropped. If it is not, the gear is kept and N is engaged at a stop.
Clutch position signalThe same open-loop trial. If the clutch can still be opened and closed, sequential is selected and shifts are limited. If it cannot, N is engaged at a stop and driving is impossible.
Selector signalThe selector is deactivated. Lamps flash only after automatic has been selected. N and R can be selected with the paddles. If neither control works, automatic is selected.
Paddle signalPaddles deactivated, with the same fallback.
Input speedLamps do not flash. Wheel speed is used instead. Shift time increases.
Power-latchLamps do not flash. The ECU stays awake and can flatten the battery. Disconnecting the battery during the power-latch stores a fault.
Gear-changing motorThe gear is kept while driving. At a stop the clutch is opened.
Clutch faultLamps do not flash. The number of shifts is reduced.

Remote faults are a loss of information from the engine ECU, the ABS ECU or the BSI, and a CAN fault. Each stored fault also keeps battery voltage, clutch status, the gear, input speed, vehicle speed, key position, whether a shift was in progress, engine speed and coolant temperature.

Software and the cars it was fitted to

A car that locks in reverse, or will not select a forward gear, is checked for injection parameters and for gearbox-actuator position before the gearbox is stripped. The correction is a gearbox software update, and the actuator is reset if the position is wrong.

After that software, the gear and AUTO symbols can flash on a gearbox that is working. The cause is ignition off while the car was still moving, even slowly, with the engine not restarted within 5 minutes. The display is resynchronised by starting, driving a short distance, stopping, waiting 5 minutes with the ignition off, and restarting. A later software removes that strategy.

Failure to select 1st or reverse is a selection-gate offset learnt wrongly at initialisation. The correction is the D4 download. Before D4 on a TU5JP4, the injection software is already the latest available. Identities are supplier 04, system 00, application 01, edition C201.

CarEngineVersion
C2TU3JPE7
C2TU5JP4EA
C2DV4TD 150 N·mE8
C2DV4TD 160 N·mEB
C3TU5JP4 up to RP 9639E1
C3TU5JP4 from RP 9640E2
C3DV4TD 150 N·mE3
C3DV4TD 160 N·mE9
C3ET3J4EE
PlurielTU5JP4 up to RP 9639E5
PlurielTU5JP4 from RP 9640E6

One oblong actuator fixing hole was later replaced by a round 9.3 mm hole for the 8 mm screw, so the actuator sits with less offset on the gates.

BSI software 39.1 is incompatible with some Sensodrive ECUs. Those gearbox ECUs are replaced before 39.1 is downloaded. DV4TD Sensodrive software was compatible. The incompatible references are 9651497480, 9651497380 and 9652762680 on Pluriel up to the OPR 9639/9640 break, 9652762280 on C2 TU3JP, 9652762580 on C2 TU5JP4, 9651497280 on C3 TU5JP4 up to OPR 9639, 9650922180 and 9652762780 on C3 TU5JP4 from OPR 9640, and 9651933780 on C3 ET3.

A gearbox that skips gears and stores P1755 has lost its learnt values. P1755 here is clutch thermal protection. The download is by architecture: D4.4 on CAN-VAN, N2.3 on full CAN. From these softwares, P1704 (brake-signal coherence) is no longer used, and P1804 is clutch-actuator thermal protection.

N2.3 references: C3 TU5JP4 9661418580, C3 ET3J4 9661418480, C3 DV4TD 9661418280, Pluriel TU5JP4 9661418780, C2 TU3A 9661419180, C2 TU5JP4 9661419280, C2 ET3J4 9661419080, C2 DV4TD 160 N·m 9661418880. The ET3J4 files are also valid for the stop-start STT2. D4.4 is a separate reference list, split by ADR and NDR and, on the Pluriel, by whether the clutch lining is chlorinated. The reference follows the car’s equipment. The two families are not interchangeable.

The MA gearbox under the actuators has its own mechanical faults, shared with the manual MA. A loose crown wheel, a manufacturing fault of April 2003, loses drive and was seen especially on C3 DV4TD driving-school cars, and it is possible on Pluriel, Saxo, Xsara and every Sensodrive. A primary-shaft bearing that starts as a noise around 50,000 miles on late-2003 and 2004 cars, DV4 excluded, will destroy the gearbox. The shaft and the bearings are replaced. A bell-housing leak on boxes built from October 2004 to January 2005 is a badly machined primary-shaft sealing face. The seal tube and the primary shaft are replaced. Any job that removes the gearbox greases the primary-shaft splines with Molykote G Rapid Plus, grease 998405.

For comparisons with other manufacturers’ systems, see BMW SMG, Ferrari F1, Maserati Cambiocorsa and Fiat systems and automated manual clutch and gearshift control. Each system has its own service and diagnostic procedures.

For separate city-car examples, see Peugeot 108 and Citroën C1 ETG operation and diagnosis. The handbook examples do not establish interchangeable actuator, fluid or learning procedures with this gearbox.

Revision 5: Sensodrive MA gearbox

Sensodrive is a five-speed MA manual gearbox with the clutch and the gear lever driven by electric motors. There is no clutch pedal and no mechanical gear linkage. The driver can leave the shifts to the ECU or take them with the selector and the steering-wheel paddles. The engine starts only with the brake pressed. It was used on the C2, C3 and C3 Pluriel, on the TU, ET3 and DV4 engines of those cars. The gearbox oil is filled for life. The clutch is the part whose temperature the ECU estimates.

A dedicated engine ECU talks to the gearbox ECU. That link is what allows a shift without lifting the accelerator: the engine ECU sets engine speed and cuts torque while the clutch is open. The gearbox ECU is Flash and is updated by download. The injection ECU is updated whenever the gearbox ECU is updated, and the other way round.

Actuators

The clutch actuator, 1665, is bolted to a bracket that also carries the ECU on rubber spacers. The bracket is four bolts to the gearbox, and the actuator is three bolts to the bracket. Inside an aluminium housing are a DC motor with two Hall sensors, a toothed segment, a compensating spring, a wear adjuster and a thrust-bearing tensioner. The clutch is a pushed type. Open and closed are both stable, and the motor is not powered to hold either of them.

To open, the ECU drives the motor, the wear adjuster locks, and the fork moves the thrust bearing. Declutch travel is about 20 mm whatever the wear. At the end of the segment travel the compensating spring helps the motor, and the motor is then switched off. Closing reverses the motor. With the clutch closed the adjuster unlocks and can shorten as the plate wears, so fork travel stays in the range the ECU has learnt. The adjuster is not repairable. The ECU has to have memorised total fork travel and the biting point.

The gearbox actuator engages each gear by lifting and then rotating the internal lever. Two motors share one housing and are not removable separately: gear-changing actuator 1663 and gear-selection actuator 1664. They never run at the same time. The three selection heights are about 5 to 7 mm apart, and the three rotational positions are about 17° to 20° apart. A ramp selects and engages together to save time.

A shift runs through preload in position, unmeshing, synchronisation, meshing and a confirmation of mesh, all under force and speed, then a retraction under current so the dog teeth are not left loaded. Once meshing has started, the ECU finishes the retraction before it will begin another shift. If a gear is hard to engage, the ECU tries twice more. Stationary, it opens and closes the clutch to help. After three failed attempts that gear is disabled and a fault is stored.

All three motors are direct current, controlled by a variable voltage. Resistance of each motor, measured on its two power pins, is about 2 ohms. The Hall sensors are supplied at 5 V, give a 0 to 5 V square wave, and produce 60 pulses per revolution.

The input-speed sensor, 1662, is a magnetic pickup facing the teeth of 2nd gear on the primary shaft. Resistance between its two pins is about 800 ohms. The wire is not shielded, so the harness route matters. The ECU uses it to see clutch slip against engine speed, to find the biting point, to close the clutch, and to see the end of synchronisation.

How a shift feels

The same phases run in automatic and in sequential. At the start the gearbox ECU tells the network that a shift is in progress and forbids a change of air-conditioning compressor state. The driver’s accelerator request is ignored and the clutch is still closed. As the clutch opens, the maximum torque the gearbox will allow is sent to the engine ECU and is updated continuously, and the engine ECU brings torque to 0 N·m by the time the clutch is open. With the clutch open, the gearbox ECU requests engine-speed regulation and moves that speed setting towards the speed that matches the gear being engaged and the road speed. The actuator does the shift in this phase. Another gear can still be requested until synchronisation of the current gear has started. Once synchronisation has started, the shift runs on to the end. The clutch then closes at one of three speeds, from the slowest and most comfortable to the fastest and most sporting, chosen from the driving style. Allowed torque rises with the clutch until it matches what the driver is asking, and the accelerator request is obeyed again.

In normal running the ECU relearns the biting point and the position where synchronisation starts, and it takes the age of the gearbox into account.

Driver controls and the laws

The left paddle is downshift and the right paddle is upshift. Paddles cannot select neutral or reverse. The selector is short-stroke and only the centre is stable: “+” up, “−” down, N and R. Between selector commands the lever has to pass through the centre. Between paddle commands the paddle has to be released. Opposite commands, a held selector or a held paddle are ignored until they are released. At every ignition-on the program is automatic. Using “+” or “−” in automatic also selects sequential and does that shift. The program button swaps between automatic and sequential, including while the car is moving. Snow is selected when wheel slip is detected, by the ESP ECU, or by the gearbox ECU from the four wheel speeds on a car that has ABS and no ESP. When slip stops, the law that was active before slip returns.

The gear and the program go from the gearbox ECU to the BSI, and the BSI repeats them to the instrument panel. Auto lit means automatic. Auto out means sequential. Snow lit means the snow law is active. A fault flashes auto and snow together and puts a dash on the gear display.

Nine laws are stored or calculated. Six are the adaptive references: L1 economy, L2 medium, L3 sport, L4 gentle slope, L5 steep slope and L6 downhill. L7 is snow. Intermediate laws between those references are calculated from the last few minutes of driving. A warm-up law runs for a time that depends on the engine, then drops out. A further law is reserved for the downgraded modes. Upshift and downshift thresholds are separated so the gearbox does not hunt. One example, at 80 percent accelerator, changes 3rd to 4th at 100 km/h and 4th back to 3rd below 72 km/h. That example is a shape of law, and every calibration does not use those speeds.

A fast lift blocks the upshift so engine braking remains, including in a corner seen from the wheel speeds, and downhill with the accelerator released. A fast press in automatic briefly raises sportiness, and lifting returns to the previous law at once. Braking downshifts can be forced, and in some cases the ECU makes a triple downshift. Kick-down delays the upshift and downshifts if the speed conditions are met. In snow, pull-away is in 2nd, shifts are less frequent, wheel torque is kept gentle, braking forces a downshift, and a kick-down downshift is allowed only below 15 km/h.

In sequential an impossible request is ignored. At maximum engine speed the ECU selects a higher gear and stays in sequential. If engine speed is too low it selects a lower gear, and if speed is still too low it opens the clutch to avoid a stall. Neutral can be engaged while moving, and the next “+” or “−” then picks a gear that fits the road speed. With the car parked and the engine off, 1st, 2nd, N and R can be engaged once the panel is active, but only one change is authorised in that state. A gear cannot be deselected with the ignition off.

After three minutes stationary with the engine running and a gear engaged, the ECU selects N. Pressing the accelerator engages 1st only if the stop has not already exceeded two minutes.

The ECU estimates clutch-plate temperature. Holding the car on a hill with the accelerator heats the clutch. When it is too hot the ECU cycles the clutch so the car oscillates until the engine stalls. The handbrake is how the car is held. The protection is that behaviour. No temperature figure is given.

What a command does

In the table, A means automatic remains or is selected, and M means the result is sequential. A single symbol is one action. A double symbol is two successive actions. Automatic, gear selector:

Engaged+−NR++−−
RA, 1stnoneA, NnoneA, RA, R
NA, 1stnonenoneA, RM, 2ndM, N
1M, 2ndM, 1stA, NA, RM, 3rdM, 1st
2M, 3rdM, 1stA, NA, RM, 4thM, 1st
3M, 4thM, 2ndA, NA, RM, 5thM, 1st
4M, 5thM, 3rdA, NA, RM, 5thM, 2nd
5M, 5thM, 4thA, NA, RM, 5thM, 3rd

Paddles have no N or R command. From N, “+” selects sequential and 1st. From 5th, “+” does nothing and “−” selects sequential and 4th. From R, the paddles do nothing. In sequential the same shifts happen and the program stays sequential. The program button swaps program and leaves the engaged gear where it is. Reverse is engaged only with the brake pressed and the car stationary. First is engaged from a “+” with the engine near idle.

A later software changes the automatic behaviour. With AUTO still displayed, a paddle or lever request is carried out at once, inside the under-rev and over-rev limits, and the gearbox returns to automatic after a time that depends on how the car is being used, or if the driver kick-downs. Permanent manual is the AUTO button. Return to automatic is the button, or ignition off. On a car below RP 10080 a paddle touch no longer leaves the car in manual for the rest of the journey, and that is explained when the car is handed back.

Starting, wake-up and the network

Unlocking the doors or opening the driver’s door runs a rapid initialisation of both actuators, switches the display on and opens the clutch if N is engaged. The ECU sleeps four minutes after the instrument panel goes off.

A full position initialisation, 10 seconds to 1 minute, runs with the ignition on and the brake pressed if the battery was disconnected before the panel went off or before the ECU slept, or if a programming operation failed. The engine is not allowed to crank during it. If programming has never been completed, this initialisation runs on every start attempt.

With 1st, 2nd or R engaged, the brake opens the clutch and cranking is allowed. Releasing the brake before the engine has started closes the clutch and cranking is refused. The starter-prohibition relay, 1005, is energised by an earth from the ECU, and only when the key is at crank, the actuators are in a start position and the brake is pressed. The relay is at the front of the left wheel arch, behind the left headlamp. On its black 9-way plug, pin 2 feeds the starter, pin 4 is 12 V from the engine relay unit, pin 5 is crank, and pin 9 is the earth from the gearbox ECU. A battery fault is stored above 16 V and below 8 V.

The ECU has a green 48-way connector and a blue 32-way connector. Permanent battery is on the green connector at L1, M1 and M2. Ignition-on is A2, crank is D4, the starter relay is B3, the driver’s door is E3, the stop switch is F3, and the K-line is H4. CAN high is J1 and CAN low is J2. Selector signals are C1, C2, E4 and H3, with the selector earth on J4. Paddles are J3 and K3, with paddle earth on K4. The program button is A4. Power earths are L3, L4 and M4.

On the blue connector the input-speed sensor is A1 and B1. The clutch motor is H2 and H3. The gear-changing motor is H1 and G1. The selection motor is H4 and G4. Two selection-actuator position inputs are listed, on C4 and D4.

Gear, program and fault information is sent on VAN and on CAN. On CAN the engine ECU receives the speed-regulation request, the speed setting, the torque reduction, the maximum torque the gearbox will allow, the compressor lock and the gear engaged. It returns engine torque, engine speed, coolant temperature, throttle position, the idle setting, the torque the driver asked for, actual torque and resistant torque. The ABS or ESP ECU provides vehicle speed, permission to shift, and whether regulation is in progress or faulty. Two brake switches are compared: a closing switch wired to the ECU, and a second switch the BSI puts on CAN.

Selector and paddle voltages

The selector has four signal wires, supplied by the ECU, and the ECU checks that the combination is coherent. Voltages are bands, measured between the electronic earth (connector pin 3, not body earth) and the signal pin. The high band is 2.4 to 4.1 V and the low band is 0.6 to 2.4 V.

PositionA1A2A3A4
Centrehighhighhighhigh
+lowlowhighhigh
−lowhighlowhigh
Nlowhighhighlow
Rhighhighlowlow

The paddles use the same two bands. Both released is high on both. The downshift paddle pressed pulls its channel low. Both pressed is low on both. The program button selects by an earth on its signal wire, and only while the button is held.

Diagnostic parameters include clutch state (slipping, clutched, declutched, synchronised), the selector position, both paddles, input speed and engine speed to 7,000 rpm, vehicle speed from the ABS ECU to 200 km/h, accelerator 0 to 100 percent, and coolant from −48 °C to 142.5 °C. Engine torque is shown both as the value from the engine ECU and as the value the gearbox ECU has calculated, over 10 to 40.8 m·daN.

Programming

Position initialisation at start-up is separate from programming. Programming stores the actuator, clutch and gate characteristics, and it is started with the diagnostic tool. The clutch actuator is always programmed before the gearbox actuator. Until programming has been done, the tool ignores actuator commands, and the start-up initialisation runs on every attempt.

Clutch end positions are learnt engine-off, car level, ignition on. The ECU opens the clutch and closes it, in about 2 seconds. The biting point is learnt with the engine idling, in N, handbrake on. The ECU makes a series of partial movements and watches the input-speed sensor for the first rotation of the primary shaft, in about 10 seconds. One replacement job allows up to 1 minute for the whole clutch-actuator program.

From diagnostic CD 32 the bite-point learn can report a false error. The manual sequence is: declutch, clutch, then the bite-point routine, end the diagnostic session and disconnect, ignition off, ignition on, select neutral, start, and with the brake held select 1st then neutral ten times, waiting 5 seconds in each neutral, then ignition off.

Gate learning is engine-off, handbrake off, car level, battery at or above 12.5 V. If voltage falls below 10.5 V the programming fails. A charger in parallel is allowed. The ignition is on and the clutch is open. One limit is 8 minutes. The job tables allow 12 minutes after refitting the actuator and 13 minutes for a gearbox refit or a clutch replacement that runs the combined sequence. The longer figure is the one the job was planned around. Afterwards the ignition is switched off, the panel is allowed to go out, and 4 minutes pass before the ignition is switched on again, so the values are stored. The same wait follows clutch programming.

The tool offers clutch only, gearbox only, and a combined sequence that does clutch ends, biting point, clutch opening, then the gate. Clutch-only asks for battery voltage above 12 V, which is a lower bar than the 12.5 V of the gate and the combined sequence.

Program the clutch after the clutch actuator is refitted, after a new clutch and after the road test, or when the ECU is replaced. Program the gate after the gearbox actuator is refitted, the gearbox is replaced, or the ECU is replaced. The combined sequence follows a gearbox refit and can replace the two separate programs after a download.

Counters are read and written, and reset when the related part is replaced. Clutch energy is stored as three levels and a total. Gear engagements are counted for 1st through 5th and reverse. Selector and paddle counts are separate. Replacing the steering-wheel controls is the reason to reset the paddle counter. On ECU replacement the counters are copied across before the combined program. Two Sensodrive ECUs are not swapped between cars. Moving one requires both programming operations on the car it is fitted to, or the actuators can be damaged. A new ECU needs no configuration.

The clutch specification is kept. A clutch of another make or with different characteristics makes the system malfunction. A mechanism that has been dropped is not fitted. Actuator tests produce high force at high speed. An actuator that has been removed is not commanded, except the assembly-position command, or it will be damaged. The fork and the internal lever are not moved by hand. Opening the driver’s door or switching the ignition on makes both actuators initialise, so the fork moves. To tow, N is engaged with the selector and confirmed on the display.

Evidence after a failed learn-in: Reproduced Citroën C3 I MA workshop information says an unsuccessful initialisation is recorded as a gearbox fault and directs the technician to note the diagnostic report and address the fault. It also describes stored context such as battery voltage, clutch and selected-gear state, input and vehicle speeds, and whether a shift was in progress. Capture these before clearing faults or attempting setup again. The document also directs checking the engine ECU fault memory when a piloted-gearbox defect is signalled. This is a C3 I example; use the current vehicle-specific service procedure and do not assume an unsuccessful initialisation identifies a defective actuator.

Downgraded behaviour

A fault flashes the auto and snow lamps and shows a dash, except where a row says the lamps stay off.

FaultBehaviour
Programming incompleteActuators initialise at ignition-on with the brake pressed. The engine cannot crank during that.
A gear jumps out, or will not engage after three attemptsThat gear is prohibited and another is selected.
A gear will not disengageThe engaged gear is kept while driving. In 3rd, 4th or 5th, the ECU declutches at a stop and the car cannot be driven. In R, 1st or 2nd, driving is still allowed.
ECU supplyNo gearbox operation.
ECU output stage, RAM or ROMActuators are no longer controlled. Driving is impossible.
Clutch or gear-changing position-sensor supplyDriving continues with reduced comfort.
Selection position signalOpen-loop is tried. If a shift is still possible, sequential is selected, shifts are limited and double or triple shifts are dropped. If it is not, the gear is kept and N is engaged at a stop.
Clutch position signalThe same open-loop trial. If the clutch can still be opened and closed, sequential is selected and shifts are limited. If it cannot, N is engaged at a stop and driving is impossible.
Selector signalThe selector is deactivated. Lamps flash only after automatic has been selected. N and R can be selected with the paddles. If neither control works, automatic is selected.
Paddle signalPaddles deactivated, with the same fallback.
Input speedLamps do not flash. Wheel speed is used instead. Shift time increases.
Power-latchLamps do not flash. The ECU stays awake and can flatten the battery. Disconnecting the battery during the power-latch stores a fault.
Gear-changing motorThe gear is kept while driving. At a stop the clutch is opened.
Clutch faultLamps do not flash. The number of shifts is reduced.

Remote faults are a loss of information from the engine ECU, the ABS ECU or the BSI, and a CAN fault. Each stored fault also keeps battery voltage, clutch status, the gear, input speed, vehicle speed, key position, whether a shift was in progress, engine speed and coolant temperature.

Software and the cars it was fitted to

A car that locks in reverse, or will not select a forward gear, is checked for injection parameters and for gearbox-actuator position before the gearbox is stripped. The correction is a gearbox software update, and the actuator is reset if the position is wrong.

After that software, the gear and AUTO symbols can flash on a gearbox that is working. The cause is ignition off while the car was still moving, even slowly, with the engine not restarted within 5 minutes. The display is resynchronised by starting, driving a short distance, stopping, waiting 5 minutes with the ignition off, and restarting. A later software removes that strategy.

Failure to select 1st or reverse is a selection-gate offset learnt wrongly at initialisation. The correction is the D4 download. Before D4 on a TU5JP4, the injection software is already the latest available. Identities are supplier 04, system 00, application 01, edition C201.

CarEngineVersion
C2TU3JPE7
C2TU5JP4EA
C2DV4TD 150 N·mE8
C2DV4TD 160 N·mEB
C3TU5JP4 up to RP 9639E1
C3TU5JP4 from RP 9640E2
C3DV4TD 150 N·mE3
C3DV4TD 160 N·mE9
C3ET3J4EE
PlurielTU5JP4 up to RP 9639E5
PlurielTU5JP4 from RP 9640E6

One oblong actuator fixing hole was later replaced by a round 9.3 mm hole for the 8 mm screw, so the actuator sits with less offset on the gates.

BSI software 39.1 is incompatible with some Sensodrive ECUs. Those gearbox ECUs are replaced before 39.1 is downloaded. DV4TD Sensodrive software was compatible. The incompatible references are 9651497480, 9651497380 and 9652762680 on Pluriel up to the OPR 9639/9640 break, 9652762280 on C2 TU3JP, 9652762580 on C2 TU5JP4, 9651497280 on C3 TU5JP4 up to OPR 9639, 9650922180 and 9652762780 on C3 TU5JP4 from OPR 9640, and 9651933780 on C3 ET3.

Check the fault description before acting: A reproduced C3 I facelift MA piloted-manual fault-code table describes P1755 as a clutch-actuator coherence fault and P1804 as activated clutch-actuator thermal protection. This contradicts an earlier description on this page that called P1755 thermal protection and attributed skipped gears to lost learned values. Do not diagnose the component, reset adaptations or apply a software download solely from the code: capture its full manufacturer description and other faults, and use the applicable vehicle and controller test plan. The linked reproduction is in Chinese; verify the exact model and current service information.

Historical notes identify D4.4 with CAN-VAN and N2.3 with full CAN, and say P1704 brake-signal coherence is no longer used from those software versions. Treat those statements as historical leads, not verified current programming instructions; confirm software applicability and any required repair with Citroën for the individual vehicle.

N2.3 references: C3 TU5JP4 9661418580, C3 ET3J4 9661418480, C3 DV4TD 9661418280, Pluriel TU5JP4 9661418780, C2 TU3A 9661419180, C2 TU5JP4 9661419280, C2 ET3J4 9661419080, C2 DV4TD 160 N·m 9661418880. The ET3J4 files are also valid for the stop-start STT2. D4.4 is a separate reference list, split by ADR and NDR and, on the Pluriel, by whether the clutch lining is chlorinated. The reference follows the car’s equipment. The two families are not interchangeable.

The MA gearbox under the actuators has its own mechanical faults, shared with the manual MA. A loose crown wheel, a manufacturing fault of April 2003, loses drive and was seen especially on C3 DV4TD driving-school cars, and it is possible on Pluriel, Saxo, Xsara and every Sensodrive. A primary-shaft bearing that starts as a noise around 50,000 miles on late-2003 and 2004 cars, DV4 excluded, will destroy the gearbox. The shaft and the bearings are replaced. A bell-housing leak on boxes built from October 2004 to January 2005 is a badly machined primary-shaft sealing face. The seal tube and the primary shaft are replaced. Any job that removes the gearbox greases the primary-shaft splines with Molykote G Rapid Plus, grease 998405.

For comparisons with other manufacturers’ systems, see BMW SMG, Ferrari F1, Maserati Cambiocorsa and Fiat systems and automated manual clutch and gearshift control. Each system has its own service and diagnostic procedures.

For separate city-car examples, see Peugeot 108 and Citroën C1 ETG operation and diagnosis. The handbook examples do not establish interchangeable actuator, fluid or learning procedures with this gearbox.