Tuning Wiki

This guide uses the 2018-edition Peugeot 108 ETG handbook and a separately documented 2015–2016 Citroën C1 ETG handbook. Each describes a five-speed electronically operated gearbox with automatic and driver-requested modes. The same marketing name can appear on other PSA vehicles: a 2013 Peugeot 208 announcement also calls its gearbox ETG5, but a name alone does not establish an identical gearbox, actuator, controller, calibration or service procedure. Identify the exact vehicle, market, transmission and ECU before diagnosing it. Peugeot 108 handbook, 2018 edition; Citroën C1 2015–2016 handbook reproduction; Peugeot: 208 ETG5 announcement.

Identify the system before testing

The 108 handbook describes five forward gears, an E automatic mode and a sequential manual mode; steering controls on equipped cars request upshifts or downshifts. For its illustrated system, the paddles do not select neutral or engage or disengage reverse. A manual-mode request is not proof of a mechanical manual gearbox, and the handbook does not establish the identity of a specific actuator or diagnostic controller on every variant.

Earlier PSA cars used different names. Peugeot's 2006 107 handbook shows “2 Tronic” with automatic and manual mode indications. Separately, the C2/C3 MA SensoDrive and C4 MCP pages describe other systems. Similar names or shared vehicle development do not make their actuator tests, wiring, fluids or learning routines interchangeable.

Related Peugeot 107 2 Tronic example

The Peugeot 107 owner's handbook describes an additional warning pattern for its 2 Tronic system: on clutch overheating, it says the controller can select neutral and flash N with an audible warning. The same manual separately identifies an illuminated gearbox warning as a fault requiring workshop attention. A flashing N can have other causes, so record the event, warning and conditions and follow the handbook for the actual model; it is not a diagnosis of clutch wear or an instruction to copy 108 service procedures. The handbook also advises using the brakes, not the accelerator, to hold the vehicle on an incline. Peugeot 107 owner's handbook: 2 Tronic operation and faults.

Separate first-generation 107/C1 service example: Clutch supplier Blue Print’s MMT clutch replacement bulletin INF122_15 lists specified 1.0-litre Peugeot 107 and Citroën C1 applications and warns that failing to set the actuator to the prescribed clamp position before gearbox removal can leave it incorrectly positioned after refitting. The bulletin identifies slip, harsh or delayed engagement and failure to select a gear as possible consequences. Where a complaint follows clutch or gearbox work, record the exact parts and setup history and check the current vehicle-specific procedure. The bulletin does not establish that its procedure or actuator fits a 108 or a later C1.

What the 108 handbook describes

ObservationDocumented 2018 108 ETG contextDiagnostic implication
Engine will not startThe manual describes starting with the brake firmly pressed and the selector in N; keyless versions also have key-recognition conditions.Check the actual selector, brake input and starting-authorisation states and relevant faults. Do not bypass an interlock or presume a failed gearbox.
No creep or manoeuvring feels differentIts creep function can be temporarily unavailable if clutch temperature is too high or a slope is too steep; an audible alarm sounds for high clutch temperature.Record the exact conditions and warning rather than treating the absence of creep alone as proof of a worn clutch or motor.
ETG warningA fixed ETG warning indicates a gearbox fault in the handbook; it calls for a qualified workshop to inspect it.Save the full fault report and operating context. The warning does not identify a particular component.
Flashing clutch warning with audible signalThe handbook identifies excessive clutch temperature and directs the driver to stop safely, select N and wait about 15 minutes for cooling.This is a model- and handbook-specific response, not a temperature threshold or a general fix for repeated warnings.
Long flashing N or flashing 1The handbook describes different selector/ignition-position checks for the two displays.Confirm the exact handbook and observed state; neither display alone proves an actuator fault. Do not use repeated selection to force a malfunctioning system.

These are owner-facing indications, not fault-code definitions or a workshop flowchart. Peugeot 108 handbook, instruments and driving sections. For the separate C1 example, its handbook also describes N and brake conditions for starting; do not assume every ETG-equipped Peugeot or Citroën uses the same conditions. Citroën C1 handbook, ETG section.

Workshop evidence and service limits

  1. Record VIN, production date, model, exact gearbox and ECU, diagnostic-tool version, recent battery or clutch work, warning, selector mode and whether the fault occurs cold, hot, during starting, first/reverse selection or a particular shift. Preserve faults and their status across the relevant controllers before clearing.
  2. With the correct equipment and current test plan, compare supply voltage, brake and selector requests, reported gear and available clutch/shift actuator feedback and speed signals. Inspect wiring and connections where the relevant fault tree directs. Distinguish a request blocked by an interlock from a commanded movement that fails to complete.
  3. For repeated slip, judder, clutch heat or no engagement, investigate friction-clutch condition, release mechanism, actuator motion, sensors, electrical supply and engine running according to the symptoms and model-specific repair information. A warning, a stored code or one learned value is evidence to test, not a replacement-parts verdict.
  4. After a confirmed repair, use the exact vehicle's instructions for calibration, adaptation and verification if required. Save existing information first: a reset cannot repair wear, damage or a bad supply. Active tests can move components; secure the vehicle and follow the specified precautions.

The owner manuals do not provide a detailed actuator failure-rate ranking, diagnostic-code chart, sensor limits or initialization sequence. Their model-specific maintenance schedules are not a universal lifetime-fluid recommendation for other ETG or MCP gearboxes. Use current manufacturer service information for the actual car and consult its handbook and recovery provider if it cannot select neutral safely.

Related: Toyota MultiMode MMT, automated manual clutch control and the electronic gearbox guide.