Page organisation in this revision
- Page type
- Technical article
- Subject
- Gearboxes
- Parent
- Section level
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- Mercedes-Benz
Changes from revision 2 to revision 3
Removed text is struck through; added text is highlighted.
Mercedes-Benz's SEQUENTRONIC name covers an automated manual transmission, not necessarily the torque-converter automatic offered in another version of the same car. This guide concerns the 716.6 six-speed transmission with option code 424, as identified in Daimler's function document for specified model 203, 208, 209, 211 and 230 applications. Vehicle range and document validity have qualifications; confirm the VIN, transmission and equipment code in the current service information. A six-speed 716.6 without code 424 is not proof that this actuation system is present. Daimler GF26.00-P-0002A: Sequentronic function.
How the documented system works
A control unit coordinates a conventional manual-type gearset and clutch. A hydraulic pump supplies energy to a pressure reservoir and hydraulic control unit; actuators operate the clutch and shift mechanism. A clutch-travel sensor, clutch-speed sensor and gear-recognition sensor provide feedback. The driver's sequential lever request is an input to the control system, not proof of a dog-engagement racing gearbox. The specified vehicle has no clutch pedal because the controller operates the clutch. Daimler 716.6 function description.
Its hydraulic pressure reservoir stores energy even after the pump stops. Daimler's 716.6 operating description explains that compressed gas drives fluid back into the circuit when required and a pressure sensor reports system pressure. Do not disconnect a line or accumulator simply because the ignition is off; use the exact current service procedure to establish and release pressure. Daimler GF26.60-P-4003-03A: accumulator function.
Symptom-led diagnosis
No gear selected or no movement: record the actual event, selected mode, engine and brake state, indicated versus requested gear, control-unit identity and any stored faults. A rejected request, a failure to release the clutch and a selector that cannot achieve a gear are different branches.
Pump not operating or hydraulic pressure not building: save fault codes and live pressure before clearing anything. Check the electrical supply, pump command, relay, wiring and applicable hydraulic circuit using the vehicle's prescribed test; check the pressure-sensor circuit if the feedback is implausible.
Frequent pumping or low indicated pressure: assess pressure, pump request, electrical supply, leaks and pressure retention under specified conditions. Pump activity alone cannot identify whether the cause is a leak, accumulator, valve, sensor or motor.
Jerky take-up or unexpected neutral: compare requested gear, recognised gear and clutch travel with brake, engine-speed and other relevant signals. Consider clutch wear or contamination, actuation, hydraulic and electrical faults, engine running and mounts. Do not bypass any start or driving interlock.
Daimler service document AF26.60-P-6005A addresses a specific 716.6 code-424 condition on listed 203, 208, 209 and 211 applications: the pump does not operate and system pressure does not build; P2080 or P2081 may be stored, and a malfunctioning relay may have caused pump overload. The document calls for both pump and relay replacement when that overload damage is confirmed. It does not prove that either fault code or every no-shift complaint has this cause. Daimler AF26.60-P-6005A.
Cold-shift mechanical comparison: Daimler document AF26.00-P-3100B describes difficult cold shifts in first and second gear on listed model 163, 170, 203, 202, 208 and 210 vehicles with specified early 716.6 gearbox serial numbers. Its historical repair concerns the mechanical gearbox lubricant level, not the Sequentronic actuator reservoir. The document does not identify code 424 separately, so establish the exact gearbox, chassis and service-document applicability before treating it as relevant to a Sequentronic. Do not copy its historical fill amounts to another transmission: confirm the current manufacturer specification. Cold-only symptoms also have other possible causes.Fluid, repair and relearning
The actuator hydraulic supply is distinct from the manual gearbox lubricant. Daimler's hydraulic-fluid level document identifies different procedures and operating-fluid specifications by transmission and vehicle, and calls for complete depressurisation before work. It includes 716.643 in specified commercial-vehicle models and code-424 passenger-car applications; that shared service document does not establish that every Sprintshift and Sequentronic component or diagnostic setting is interchangeable. Use the manufacturer's current data for the exact chassis and transmission. Daimler AR26.60-D-0009A: hydraulic oil.
After a confirmed repair, follow the applicable bleeding, control-unit adaptation and verification steps with a compatible diagnostic system. Do not treat a reset as a repair for a leaking circuit, bad pump supply or worn clutch. Record fault state and freeze-frame information first, and verify the original complaint in appropriate conditions.
Other Mercedes clutch arrangements
Mercedes has also used an automatic clutch system with a manually shifted gearbox on A-Class applications. An automated clutch with an H-pattern lever is a different arrangement from a controller that selects gears as well. A diagnostic-tool manufacturer lists the A-Class AKS clutch controller and separate automatic-transmission and gear-recognition systems; this listing documents tool coverage, not the equipment fitted to every A-Class. Autologic A-Class system coverage.
For comparison see Sprinter Sprintshift 716.643, smart fortwo 451 automated manual, automated clutch and gearshift control and the automated-manual gearbox overview.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: Mercedes Benz Sequentronic 716.6 operation faults and diagnosis
Mercedes-Benz's SEQUENTRONIC name covers an automated manual transmission, not necessarily the torque-converter automatic offered in another version of the same car. This guide concerns the 716.6 six-speed transmission with option code 424, as identified in Daimler's function document for specified model 203, 208, 209, 211 and 230 applications. Vehicle range and document validity have qualifications; confirm the VIN, transmission and equipment code in the current service information. A six-speed 716.6 without code 424 is not proof that this actuation system is present. Daimler GF26.00-P-0002A: Sequentronic function.
How the documented system works
A control unit coordinates a conventional manual-type gearset and clutch. A hydraulic pump supplies energy to a pressure reservoir and hydraulic control unit; actuators operate the clutch and shift mechanism. A clutch-travel sensor, clutch-speed sensor and gear-recognition sensor provide feedback. The driver's sequential lever request is an input to the control system, not proof of a dog-engagement racing gearbox. The specified vehicle has no clutch pedal because the controller operates the clutch. Daimler 716.6 function description.
Its hydraulic pressure reservoir stores energy even after the pump stops. Daimler's 716.6 operating description explains that compressed gas drives fluid back into the circuit when required and a pressure sensor reports system pressure. Do not disconnect a line or accumulator simply because the ignition is off; use the exact current service procedure to establish and release pressure. Daimler GF26.60-P-4003-03A: accumulator function.
Symptom-led diagnosis
- No gear selected or no movement: record the actual event, selected mode, engine and brake state, indicated versus requested gear, control-unit identity and any stored faults. A rejected request, a failure to release the clutch and a selector that cannot achieve a gear are different branches.
- Pump not operating or hydraulic pressure not building: save fault codes and live pressure before clearing anything. Check the electrical supply, pump command, relay, wiring and applicable hydraulic circuit using the vehicle's prescribed test; check the pressure-sensor circuit if the feedback is implausible.
- Frequent pumping or low indicated pressure: assess pressure, pump request, electrical supply, leaks and pressure retention under specified conditions. Pump activity alone cannot identify whether the cause is a leak, accumulator, valve, sensor or motor.
- Jerky take-up or unexpected neutral: compare requested gear, recognised gear and clutch travel with brake, engine-speed and other relevant signals. Consider clutch wear or contamination, actuation, hydraulic and electrical faults, engine running and mounts. Do not bypass any start or driving interlock.
Daimler service document AF26.60-P-6005A addresses a specific 716.6 code-424 condition on listed 203, 208, 209 and 211 applications: the pump does not operate and system pressure does not build; P2080 or P2081 may be stored, and a malfunctioning relay may have caused pump overload. The document calls for both pump and relay replacement when that overload damage is confirmed. It does not prove that either fault code or every no-shift complaint has this cause. Daimler AF26.60-P-6005A.
Fluid, repair and relearning
The actuator hydraulic supply is distinct from the manual gearbox lubricant. Daimler's hydraulic-fluid level document identifies different procedures and operating-fluid specifications by transmission and vehicle, and calls for complete depressurisation before work. It includes 716.643 in specified commercial-vehicle models and code-424 passenger-car applications; that shared service document does not establish that every Sprintshift and Sequentronic component or diagnostic setting is interchangeable. Use the manufacturer's current data for the exact chassis and transmission. Daimler AR26.60-D-0009A: hydraulic oil.
After a confirmed repair, follow the applicable bleeding, control-unit adaptation and verification steps with a compatible diagnostic system. Do not treat a reset as a repair for a leaking circuit, bad pump supply or worn clutch. Record fault state and freeze-frame information first, and verify the original complaint in appropriate conditions.
Other Mercedes clutch arrangements
Mercedes has also used an automatic clutch system with a manually shifted gearbox on A-Class applications. An automated clutch with an H-pattern lever is a different arrangement from a controller that selects gears as well. A diagnostic-tool manufacturer lists the A-Class AKS clutch controller and separate automatic-transmission and gear-recognition systems; this listing documents tool coverage, not the equipment fitted to every A-Class. Autologic A-Class system coverage.
For comparison see Sprinter Sprintshift 716.643, smart fortwo 451 automated manual, automated clutch and gearshift control and the automated-manual gearbox overview.
Revision 3: Mercedes Benz Sequentronic 716.6 operation faults and diagnosis
Mercedes-Benz's SEQUENTRONIC name covers an automated manual transmission, not necessarily the torque-converter automatic offered in another version of the same car. This guide concerns the 716.6 six-speed transmission with option code 424, as identified in Daimler's function document for specified model 203, 208, 209, 211 and 230 applications. Vehicle range and document validity have qualifications; confirm the VIN, transmission and equipment code in the current service information. A six-speed 716.6 without code 424 is not proof that this actuation system is present. Daimler GF26.00-P-0002A: Sequentronic function.
How the documented system works
A control unit coordinates a conventional manual-type gearset and clutch. A hydraulic pump supplies energy to a pressure reservoir and hydraulic control unit; actuators operate the clutch and shift mechanism. A clutch-travel sensor, clutch-speed sensor and gear-recognition sensor provide feedback. The driver's sequential lever request is an input to the control system, not proof of a dog-engagement racing gearbox. The specified vehicle has no clutch pedal because the controller operates the clutch. Daimler 716.6 function description.
Its hydraulic pressure reservoir stores energy even after the pump stops. Daimler's 716.6 operating description explains that compressed gas drives fluid back into the circuit when required and a pressure sensor reports system pressure. Do not disconnect a line or accumulator simply because the ignition is off; use the exact current service procedure to establish and release pressure. Daimler GF26.60-P-4003-03A: accumulator function.
Symptom-led diagnosis
- No gear selected or no movement: record the actual event, selected mode, engine and brake state, indicated versus requested gear, control-unit identity and any stored faults. A rejected request, a failure to release the clutch and a selector that cannot achieve a gear are different branches.
- Pump not operating or hydraulic pressure not building: save fault codes and live pressure before clearing anything. Check the electrical supply, pump command, relay, wiring and applicable hydraulic circuit using the vehicle's prescribed test; check the pressure-sensor circuit if the feedback is implausible.
- Frequent pumping or low indicated pressure: assess pressure, pump request, electrical supply, leaks and pressure retention under specified conditions. Pump activity alone cannot identify whether the cause is a leak, accumulator, valve, sensor or motor.
- Jerky take-up or unexpected neutral: compare requested gear, recognised gear and clutch travel with brake, engine-speed and other relevant signals. Consider clutch wear or contamination, actuation, hydraulic and electrical faults, engine running and mounts. Do not bypass any start or driving interlock.
Daimler service document AF26.60-P-6005A addresses a specific 716.6 code-424 condition on listed 203, 208, 209 and 211 applications: the pump does not operate and system pressure does not build; P2080 or P2081 may be stored, and a malfunctioning relay may have caused pump overload. The document calls for both pump and relay replacement when that overload damage is confirmed. It does not prove that either fault code or every no-shift complaint has this cause. Daimler AF26.60-P-6005A.
Cold-shift mechanical comparison: Daimler document AF26.00-P-3100B describes difficult cold shifts in first and second gear on listed model 163, 170, 203, 202, 208 and 210 vehicles with specified early 716.6 gearbox serial numbers. Its historical repair concerns the mechanical gearbox lubricant level, not the Sequentronic actuator reservoir. The document does not identify code 424 separately, so establish the exact gearbox, chassis and service-document applicability before treating it as relevant to a Sequentronic. Do not copy its historical fill amounts to another transmission: confirm the current manufacturer specification. Cold-only symptoms also have other possible causes.
Fluid, repair and relearning
The actuator hydraulic supply is distinct from the manual gearbox lubricant. Daimler's hydraulic-fluid level document identifies different procedures and operating-fluid specifications by transmission and vehicle, and calls for complete depressurisation before work. It includes 716.643 in specified commercial-vehicle models and code-424 passenger-car applications; that shared service document does not establish that every Sprintshift and Sequentronic component or diagnostic setting is interchangeable. Use the manufacturer's current data for the exact chassis and transmission. Daimler AR26.60-D-0009A: hydraulic oil.
After a confirmed repair, follow the applicable bleeding, control-unit adaptation and verification steps with a compatible diagnostic system. Do not treat a reset as a repair for a leaking circuit, bad pump supply or worn clutch. Record fault state and freeze-frame information first, and verify the original complaint in appropriate conditions.
Other Mercedes clutch arrangements
Mercedes has also used an automatic clutch system with a manually shifted gearbox on A-Class applications. An automated clutch with an H-pattern lever is a different arrangement from a controller that selects gears as well. A diagnostic-tool manufacturer lists the A-Class AKS clutch controller and separate automatic-transmission and gear-recognition systems; this listing documents tool coverage, not the equipment fitted to every A-Class. Autologic A-Class system coverage.
For comparison see Sprinter Sprintshift 716.643, smart fortwo 451 automated manual, automated clutch and gearshift control and the automated-manual gearbox overview.