Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Gearboxes
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None
Bosch 8HP mechatronic showing part number 0260550074
Bosch mechatronic, showing part number 0260550074 in MaxxECU’s Gen1 identification guide. Photo: MaxxECU; source: MaxxECU installation and wiring manual. Reproduced with permission.

Some first-generation ZF 8HP transmissions use an original mechatronic transmission control module (TCM/TCU) with Bosch identification numbers. BMW also uses the term EGS for electronic transmission control. This page is an identification guide for the specific examples cited below; it is not a universal Bosch part-number, firmware or interchange list for all 8HP transmissions.

In the documented Porsche 8HP65AX application, the electronic TCU and hydraulic control unit form one mechatronic assembly inside the gearbox; individual sensors and pressure-control components are part of that described assembly. The Porsche system description is an example of the architecture and does not establish the manufacturer or pinout of all GEN1 units. See ZF 8HP gearbox controllers for the wider family.

Find the identification

  1. Record the transmission type and full suffix, catalogue or specification number, transmission serial number, donor VIN and vehicle. The ZF 2018 remanufactured transmission catalogue, figure 2, shows where the catalogue number, type and OE control-module hardware number can appear on an example 6HP/8HP label.
  2. Record the mechatronic part number and the electronically read TCU identification, hardware and software information. ZF’s 8HP mechatronic service information directs kit selection by the mechatronic part number; transmission designation is additional guidance.
  3. Distinguish the Bosch part number from the Bosch TCU ID. MaxxECU’s 8HP installation page illustrates both labels and lists reported ID, part number, CPU family, gearbox and example donor together. Compare all available identifiers with the exact application and supplier’s instructions.

Documented example Bosch identifiers

MaxxECU’s TCU support table lists these examples with SH725xx CPU designation. Its support status refers to the aftermarket MaxxECU firmware, not to factory interchangeability or an OE parts supersession. A repeated TCU ID does not prove that all hardware, software, immobiliser and gearbox combinations are interchangeable.

Reported Bosch TCU IDReported Bosch part numberGearbox and donor in supplier table
103442022102605500758HP70, BMW E70 X5 4.4, 2013
1034420235Not specified in this row8HP45, BMW 335i N55
103442023602605500748HP70, BMW 5 F10/F11
103442023702605500768HP70, Jaguar XF CC9 2.2 diesel, 2015
1034420267Not specified in these rows8HP70, Dodge Charger 2018; 8HP90, Dodge Challenger Hellcat 2016
1034420285Not specified in this row8HP70, VW Amarok 2016
103442028802605500748HP70, Dodge RAM Classic 5.7 RWD, 2020

Preserve the distinction between an identifier read from a control unit and an OE or ZF number on a label. The table does not identify a distinct connector pinout for each listed ID; source-specific electrical data must be checked for the actual donor and TCU.

Example connector: Dodge GEN1 8HP as documented for MaxxECU

MaxxECU’s installation and wiring manual gives the following assignments for the Dodge 8HP GEN1 transmission connector. Its diagram is viewed looking into the connector’s terminal side. The supplier does not associate this table with every Bosch ID or model year above. Verify the connector and cavity markings against the vehicle wiring information and supplier’s diagram before applying power; this table does not establish a pinout for BMW, Jaguar, Audi or other variants.

CavityMaxxECU’s documented function
5CAN High
6CAN Low
9+12 V wake-up
13+12 V main supply
14Ground

Other cavities are shown with dashes in that table; do not assume they are unused in an OE vehicle. For its own reflash/control installation MaxxECU says main power should be active continuously or for at least 10–15 seconds before wake-up, and notes the 8HP TCU has no built-in CAN termination. The complete installation instructions and the applicable OE wiring diagram take precedence. This is not a programming, bypass-board or universal 8HP connection guide.

Factory vehicle matching

BMW’s service bulletin B24 03 15 covers BMW vehicles with ZF 6HP/8HP and EWS4. It says the programmed mechatronic is paired with the DME and CAS for the specific VIN and warns that an unmatched used unit can prevent gear selection. That statement is scoped to the BMW EWS4 vehicles in the bulletin; it does not establish the security procedure of another make or every 8HP.

Images and related information

The MaxxECU illustrated manual shows examples of Bosch part-number and TCU-ID labels, the transmission connector and its terminal view. The ZF catalogue includes transmission plate identification images. Additional illustrations are available on those sites; credits: MaxxECU and ZF.

For MaxxECU-specific reflashing and harness details see MaxxECU ZF 8HP transmission control. See ZF 8HP gearbox types for assembly identification. Sources reviewed 17 November 2026.

Community fitting reports and guides

In a June 2025 Bimmerpost retrofit guide, owner alexnaoumov describes a successful E90 330i 8HP installation and discusses the donor gearbox, shifter, wiring, control-module selection and coding. The author calls the guide a developing retrofit and notes that the particular vehicle and engine require checking. Treat the guide's proposed interchange and wiring claims as a starting point for verification, not an OE compatibility or pinout guarantee.

In a separate E90 owner report, the poster describes a 2010 328i LCI with a 2014 E84 8HP45 donor, a replacement 8HP connector and shifter, and transmission flashing and vehicle coding. They report a cooler-line leak after using generic O-rings and recommend the correct OE cooler-line seals; they also describe a flywheel rattle they had yet to investigate. The account concerns that single conversion and is not an approved parts list for all E90s. Verify seals, driveline fit, security and wiring against the exact donor and vehicle.