Tuning Wiki
MaxxECU first-generation 8HP connection harness
MaxxECU first-generation 8HP connection harness. Photo: MaxxECU; source: MaxxECU installation and wiring manual. Reproduced with permission.

MaxxECU’s 8HP control uses a MaxxECU engine-management unit to communicate over CAN with the transmission’s original TCU after that TCU has been reflashed with MaxxECU-specific firmware. It is a control system using a retained and reprogrammed TCU, rather than a separate replacement for the mechatronic solenoid drivers. MaxxECU describes this feature as beta in its installation and wiring manual. See the ZF 8HP controllers overview for other architectures.

Identification and compatibility

The supplier’s compatibility table and identification photographs list selected first-generation 8HP45, 8HP70 and 8HP90 combinations as working in beta. They list 8HP30 as no support planned, Audi 8HP55 development as paused, and 8HP65 as no support planned. GEN2 and GEN3 are not supported in the reviewed documentation. On listed AWD donors, MaxxECU says its control covers the rear-wheel-drive portion only, not the transfer case. Do not use a generation or the transmission label alone to establish support.

Record the gearbox identification plate, donor vehicle, Bosch TCU ID and Bosch part number. Compare both numbers and application with the supplier’s current table. Examples listed as working in beta include:

Bosch TCU IDBosch part numberListed example
103442022102605500758HP70; BMW E70 X5 4.4, 2013
103442023602605500748HP70; BMW 5 F10/F11
103442023702605500768HP70; Jaguar XF CC9 2.2 diesel, 2015
1034420267Not specified in the cited example8HP90; Dodge Challenger Hellcat, 2016
103442028802605500748HP70; Dodge RAM Classic 5.7 RWD, 2020

These are examples from the supplier’s table, not a complete list or a guarantee for every controller bearing the same number. Contact MaxxECU with the actual TCU identification and donor information before purchasing or programming. The installation manual notes that mixed cable-and-CAN “semi shift” variants may cause problems.

Harness and selector

MaxxECU identifies GEN1 harness 2283 for the Dodge 8HP shifter and 2287 for the BMW 8HP shifter; its manual states that only its own harnesses are supported. Its documented options also include sequential shifting and shifter emulation. Confirm the specific selector part number against the supplier’s selector list and illustrations.

Verified connection assignments: Dodge GEN1 transmission connector

This table reproduces the numbered functions in MaxxECU’s Dodge 8HP GEN1 connector pinout, for its 8HP control installation. Identify the physical connector and moulded cavity numbers against the supplier’s drawing, which shows the connector looking into the terminal side. This is not a universal 8HP or BMW connector pinout. Other cavities are shown with a dash in the source; that is not proof of their function in another application.

CavityFunction in MaxxECU’s Dodge GEN1 table
5CAN High
6CAN Low
9+12 V wake-up signal
13+12 V main power supply
14Ground

MaxxECU states that main power must already be active continuously or for at least 10–15 seconds before wake-up; otherwise the TCU may not initialise correctly. The same manual says the 8HP TCU has no built-in CAN termination. Follow its full wiring, protection, termination and power sequencing instructions for the actual harness and configuration.

Verified connection assignments: 12-way GT150 interface

The separate MaxxECU wiring table identifies these lettered cavities for the 12-pin GT150 connector. This is the harness interface, not the numbered Dodge gearbox connector above. Check the housing markings and manufacturer diagram before connecting power.

CavitySupplier’s assignment
A+12 V main supply, 15 A fused; constant or power-hold relay
B+12 V wake-up, key-on
CCAN High to MaxxECU
GGround to chassis/engine
JCAN Low to MaxxECU

Only functions specified in that source are shown. The same main-power-before-wake-up requirement applies in the supplier’s instructions.

Firmware and integration

The MaxxECU reflash procedure calls for its recommended ACDP2 tool and instructs the installer to supply the TCU identification and internal-flash and EEPROM readouts to support for beta firmware. It warns that its code/calibration is intended for MaxxECU EMS and must not be used with an original Dodge or other engine ECU/PCM. Preserve and identify the original readouts and follow the current vendor instructions rather than assuming firmware or recovery procedures are interchangeable.

When a separate engine ECU is used, MaxxECU requires accurate engine data, calibration of its torque model and a means for the engine ECU to perform requested torque reduction and blipping. The supplier says it does not provide troubleshooting or documentation for third-party engine-management setups and advises against OE ECU use without torque reduction on demand. See standalone 8HP control for the required inputs and limitations.

Manufacturer photographs and documentation

MaxxECU’s illustrated installation manual includes photographs of the harness, TCU identification markings, shifters and connector views. Its 8HP product overview includes product and system images. Source and credit: MaxxECU.

Related: ZF 8HP gearbox types and ZF 6HP and 8HP tuning and swap diagnosis. Manufacturer documentation reviewed 17 November 2026; compatibility and beta status can change.

Community installation reports

These are owner accounts, not independent validation of fitment, wiring or calibration. Check the exact TCU ID, transmission, harness and current supplier documentation before using them on another build.

  • BMW E21 / turbo M20 / 8HP45: In an October 2024 R3VLimited build thread, E21M20B27 describes a MaxxECU Race installation with a reflashed 8HP45, an F10 selector, custom propshaft and cooler. The builder reports that an assumed engine angle caused bellhousing alignment trouble, and that correcting swapped CAN wires resolved an initial communication fault. In the 26 October update, road testing was still limited by cooling problems and lack of an MOT; the builder also described difficulty holding the raised driven axle stationary with the brakes in some modes. This is a report on that car, not a measured general braking or shift-performance claim. Measure the actual installation and investigate brake and transmission behaviour safely before use.
  • LS3 / 8HP70: In a December 2025 Reddit discussion, user shainiac reports using MaxxECU for both a twin-turbo LS3 and a BMW-sourced 8HP70 with an engine-to-transmission adapter. The owner preferred its street behaviour to a previous DCT but reported needing more engine torque reduction on full-throttle shifts. This is one owner's comparison with their particular previous setup, not a general performance or torque-capacity rating.

For each swap, confirm the actual adapter, converter engagement, transmission identification, CAN wiring, engine torque model and torque-request response against the current component suppliers' instructions. Forum discussion reviewed 17 November 2026.

Continue the conversation

If this topic interests you, consider joining the following forums. They host material referenced in this article.