Page organisation in this revision
- Page type
- Technical article
- Subject
- Flywheels
- Parent
- Section level
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 1 to revision 2
Removed text is struck through; added text is highlighted.
Automatic and dual-clutch transmissions do not all use the same engine-to-gearbox connection. Identify the actual assembly before ordering parts or applying a manual-transmission flywheel test.
Torque-converter automatic: flexplate
A conventional torque-converter automatic commonly uses a relatively thin flexplate or driveplate between the crankshaft and torque converter. It may also carry the starter ring gear. This is a different arrangement from the friction face and pressure plate of a typical manual clutch; some vehicles add adapters, damping or other components, and names vary by manufacturer.
Fitment depends on the crankshaft register and bolt pattern, converter attachment, starter gear and alignment, correct hardware and the engine's balance arrangement. Converter seating and clearance also matter. Follow the relevant vehicle and component instructions instead of transferring a clearance value from a different transmission. ATI: converter alignment and clearance; ATI: an example application-specific flexplate kit.
Dual-clutch transmissions
A dual-clutch gearbox uses two clutches to select different gear paths. A DMF can still be fitted between the engine and the clutch unit. For example, Audi's self-study programme for the 02E six-speed twin-clutch gearbox describes torque passing through a DMF and a splined connection to the twin clutch; that gearbox uses wet clutches. This example does not establish the layout of every DSG or other dual-clutch transmission. Audi SSP 386: 02E gearbox power flow.
The flywheel-to-clutch interface and inspection procedure may differ from a manual's. In particular, ZF excludes dual-clutch DMF designs from the scope of the standard SACHS DMF test kit described in its instructions. Find the procedure for the specific gearbox and flywheel rather than using an unsupported free-play limit. ZF: test-tool application limits.
For a Ferrari example, the California dual-clutch gearbox guide explains the documented separate gear-oil and clutch-fluid services and cooling layouts.Practical distinction
A torque converter contains its own fluid coupling and may have a lock-up clutch; a dual-clutch transmission uses clutch packs and gearsets in a different arrangement. Their flywheels, driveplates, diagnostics and service parts are not interchangeable merely because both shift automatically.
See the flywheel overview, single- and dual-mass designs, fitment and balancing and gearbox and transmission control catalogue.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Flexplates and dual clutch flywheels
Automatic and dual-clutch transmissions do not all use the same engine-to-gearbox connection. Identify the actual assembly before ordering parts or applying a manual-transmission flywheel test.
Torque-converter automatic: flexplate
A conventional torque-converter automatic commonly uses a relatively thin flexplate or driveplate between the crankshaft and torque converter. It may also carry the starter ring gear. This is a different arrangement from the friction face and pressure plate of a typical manual clutch; some vehicles add adapters, damping or other components, and names vary by manufacturer.
Fitment depends on the crankshaft register and bolt pattern, converter attachment, starter gear and alignment, correct hardware and the engine's balance arrangement. Converter seating and clearance also matter. Follow the relevant vehicle and component instructions instead of transferring a clearance value from a different transmission. ATI: converter alignment and clearance; ATI: an example application-specific flexplate kit.
Dual-clutch transmissions
A dual-clutch gearbox uses two clutches to select different gear paths. A DMF can still be fitted between the engine and the clutch unit. For example, Audi's self-study programme for the 02E six-speed twin-clutch gearbox describes torque passing through a DMF and a splined connection to the twin clutch; that gearbox uses wet clutches. This example does not establish the layout of every DSG or other dual-clutch transmission. Audi SSP 386: 02E gearbox power flow.
The flywheel-to-clutch interface and inspection procedure may differ from a manual's. In particular, ZF excludes dual-clutch DMF designs from the scope of the standard SACHS DMF test kit described in its instructions. Find the procedure for the specific gearbox and flywheel rather than using an unsupported free-play limit. ZF: test-tool application limits.
Practical distinction
A torque converter contains its own fluid coupling and may have a lock-up clutch; a dual-clutch transmission uses clutch packs and gearsets in a different arrangement. Their flywheels, driveplates, diagnostics and service parts are not interchangeable merely because both shift automatically.
See the flywheel overview, single- and dual-mass designs, fitment and balancing and gearbox and transmission control catalogue.
Revision 2: Flexplates and dual clutch flywheels
Automatic and dual-clutch transmissions do not all use the same engine-to-gearbox connection. Identify the actual assembly before ordering parts or applying a manual-transmission flywheel test.
Torque-converter automatic: flexplate
A conventional torque-converter automatic commonly uses a relatively thin flexplate or driveplate between the crankshaft and torque converter. It may also carry the starter ring gear. This is a different arrangement from the friction face and pressure plate of a typical manual clutch; some vehicles add adapters, damping or other components, and names vary by manufacturer.
Fitment depends on the crankshaft register and bolt pattern, converter attachment, starter gear and alignment, correct hardware and the engine's balance arrangement. Converter seating and clearance also matter. Follow the relevant vehicle and component instructions instead of transferring a clearance value from a different transmission. ATI: converter alignment and clearance; ATI: an example application-specific flexplate kit.
Dual-clutch transmissions
A dual-clutch gearbox uses two clutches to select different gear paths. A DMF can still be fitted between the engine and the clutch unit. For example, Audi's self-study programme for the 02E six-speed twin-clutch gearbox describes torque passing through a DMF and a splined connection to the twin clutch; that gearbox uses wet clutches. This example does not establish the layout of every DSG or other dual-clutch transmission. Audi SSP 386: 02E gearbox power flow.
The flywheel-to-clutch interface and inspection procedure may differ from a manual's. In particular, ZF excludes dual-clutch DMF designs from the scope of the standard SACHS DMF test kit described in its instructions. Find the procedure for the specific gearbox and flywheel rather than using an unsupported free-play limit. ZF: test-tool application limits.
For a Ferrari example, the California dual-clutch gearbox guide explains the documented separate gear-oil and clutch-fluid services and cooling layouts.
Practical distinction
A torque converter contains its own fluid coupling and may have a lock-up clutch; a dual-clutch transmission uses clutch packs and gearsets in a different arrangement. Their flywheels, driveplates, diagnostics and service parts are not interchangeable merely because both shift automatically.
See the flywheel overview, single- and dual-mass designs, fitment and balancing and gearbox and transmission control catalogue.