Removed text is struck through; added text is highlighted.
The Emtron TM16 is a programmable external transmission control module. It can be configured for a ZF 8HP using Emtron's documented 8HP setup. The factory TCM is bypassed in that setup, so it is not interchangeable with systems retaining the unmodified factory controller. Emtron TM16 datasheet and product photograph; Emtron ZF 8HP guide.
Emtron TM16 transmission controller. Image and credit: Emtron Australia. Permission to republish confirmed by the user.
Identification and compatibility
Identify the module as TM16 and record hardware and firmware versions, the transmission plate and mechatronic part numbers, connector and valve-body configuration. The datasheet lists three mating connectors: A 4-1437290-0, B 4-1437290-1 and C 3-1437290-7. TMtune is used for configuration. The 8HP base calibration is based on 8HP70 and is a starting point requiring setup for the actual installation.
Emtron's 8HP guide lists 8HP45, 50, 70, 75, 90 and 95 as supported. It marks 8HP51 and 76 as requiring a Gen 2 valve body. Only gearboxes with 16-pin connectors are supported in this setup; the guide says 10-pin versions lack the necessary inputs and outputs. Confirm the exact assembly and current requirements with Emtron before buying or modifying it.
TM16 controller pinout
The following is the controller-side pin assignment from the Emtron TM16 datasheet, which depicts the view looking into the TCM. Names below are the manufacturer's hardware functions, not fixed 8HP wiring assignments. Use the datasheet connector drawing and power supply guidance for fusing, supply, grounding and output-bank requirements. Inputs and outputs must agree with the actual calibration.
The manufacturer's 8HP instructions show the internal bypass, the transmission connector view, base-calibration wiring and Gen 1/Gen 2 solenoid differences. These connections apply only after the specified mechatronic modifications, not to a standard factory TCU. The source's table labels one Gen 2 entry as pin 17, while its accompanying note says swap pins 15 and 16; confirm the discrepancy with Emtron and the numbered connector before wiring. Do not infer the missing assignment.
Emtron specifies digital inputs rather than the dedicated Hall inputs for the 8HP speed sensors and requires the appropriate pulldown and thresholds. Verify sensor signals, solenoid assignments and current-control calibration for the exact gearbox. The Emtron ECU integration guide documents CAN and engine-torque coordination for its ECU.
See ZF 8HP gearbox controllers and ZF 8HP gearbox types. Sources reviewed 17 November 2026.
Published build examples
Engine Swap Depot's September 2026 feature describes a Mach1 Motorsport BMW E30 with a turbo Mitsubishi 4G63, an adapter, an 8HP70 and an Emtron TM16. The article identifies the parts but does not provide a wiring diagram, calibration or detailed driving assessment; it is a reported build example, not proof that the same package fits another car.
In its 8 October 2026 customer-build feature, Emtron describes the owner of a 2JZ-powered Toyota 86 with an 8HP70 moving to a KV8 engine ECU, TM16 and ED7 display. This is a manufacturer feature describing a conversion in progress, not an independent completed-installation report. Check the individual gearbox, modified mechatronics and engine torque integration against the current Emtron instructions. Sources reviewed 17 November 2026.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 3: Emtron TM16 for ZF 8HP
The Emtron TM16 is a programmable external transmission control module. It can be configured for a ZF 8HP using Emtron's documented 8HP setup. The factory TCM is bypassed in that setup, so it is not interchangeable with systems retaining the unmodified factory controller. Emtron TM16 datasheet and product photograph; Emtron ZF 8HP guide.
Emtron TM16 transmission controller. Image and credit: Emtron Australia. Permission to republish confirmed by the user.
Identification and compatibility
Identify the module as TM16 and record hardware and firmware versions, the transmission plate and mechatronic part numbers, connector and valve-body configuration. The datasheet lists three mating connectors: A 4-1437290-0, B 4-1437290-1 and C 3-1437290-7. TMtune is used for configuration. The 8HP base calibration is based on 8HP70 and is a starting point requiring setup for the actual installation.
Emtron's 8HP guide lists 8HP45, 50, 70, 75, 90 and 95 as supported. It marks 8HP51 and 76 as requiring a Gen 2 valve body. Only gearboxes with 16-pin connectors are supported in this setup; the guide says 10-pin versions lack the necessary inputs and outputs. Confirm the exact assembly and current requirements with Emtron before buying or modifying it.
TM16 controller pinout
The following is the controller-side pin assignment from the Emtron TM16 datasheet, which depicts the view looking into the TCM. Names below are the manufacturer's hardware functions, not fixed 8HP wiring assignments. Use the datasheet connector drawing and power supply guidance for fusing, supply, grounding and output-bank requirements. Inputs and outputs must agree with the actual calibration.
Connector A
Pin
Function
A1
ANV 1
A2
ANV 2
A3
ANV 3
A4
ANV 4
A5
ANV 5
A6
ANV 6
A7
ANV 7
A8
ANV 8
A9
Sensor 0V Ref
A10
ANV 9
A11
ANV 10
A12
ANV 11
A13
ANV 12
A14
ANV 13
A15
ANV 14
A16
ANV 15
A17
ANV 16
A18
DI 1
A19
DI 2
A20
DI 3
A21
DI 4
A22
DI 5
A23
DI 6
A24
DI 7
A25
DI 8
A26
DI 9
A27
DI 10
A28
DI 11
A29
DI 12
A30
DI 13
A31
DI 14
A32
DI 15
A33
DI 16
A34
Sensor 0V Ref
Connector B
Pin
Function
B1
Aux 1
B2
Aux 2
B3
Aux 3
B4
Aux 4
B5
Aux 5
B6
Aux 6
B7
Aux 7
B8
Aux 8
B9
GND
B10
Solenoid 1
B11
Solenoid 2
B12
Solenoid 3
B13
Solenoid 4
B14
Solenoid 5
B15
Solenoid 6
B16
Solenoid 7
B17
Solenoid 8
B18
Solenoid 9
B19
Solenoid 10
B20
Solenoid 11
B21
Solenoid 12
B22
Solenoid 13
B23
Solenoid 14
B24
Solenoid 15
B25
Solenoid 16
B26
Analog Out 1
B27
Analog Out 2
B28
Analog Out 3
B29
Analog Out 4
B30
Solenoid 1-4 Supply Output
B31
Solenoid 5-8 Supply Output
B32
Solenoid 9-12 Supply Output
B33
Solenoid 13-16 Supply Output
B34
GND
Connector C
Pin
Function
C1
Battery Hot Supply
C2
Aux 1-4 Supply
C3
Aux 5-8 Supply
C4
Solenoid 1-8 Supply
C5
Solenoid 9-16 Supply
C6
Ignition Switch
C7
GND
C8
CAN 1 Hi
C9
CAN 2 Hi
C10
Hall 1
C11
Hall 2
C12
Hall 3
C13
Hall 4
C14
CAN 1 Lo
C15
CAN 2 Lo
C16
5V0 Ref Output 1
C17
5V0 Ref Output 2
C18
8V0 Ref Output
C19
Sensor 0V Ref
C20
Ethernet Rx+
C21
Ethernet Rx-
C22
Ethernet Tx+
C23
Ethernet Tx-
C24
RS232 Rx
C25
RS232 Tx
C26
GND
8HP-specific wiring and identification
The manufacturer's 8HP instructions show the internal bypass, the transmission connector view, base-calibration wiring and Gen 1/Gen 2 solenoid differences. These connections apply only after the specified mechatronic modifications, not to a standard factory TCU. The source's table labels one Gen 2 entry as pin 17, while its accompanying note says swap pins 15 and 16; confirm the discrepancy with Emtron and the numbered connector before wiring. Do not infer the missing assignment.
Emtron specifies digital inputs rather than the dedicated Hall inputs for the 8HP speed sensors and requires the appropriate pulldown and thresholds. Verify sensor signals, solenoid assignments and current-control calibration for the exact gearbox. The Emtron ECU integration guide documents CAN and engine-torque coordination for its ECU.
Engine Swap Depot's September 2026 feature describes a Mach1 Motorsport BMW E30 with a turbo Mitsubishi 4G63, an adapter, an 8HP70 and an Emtron TM16. The article identifies the parts but does not provide a wiring diagram, calibration or detailed driving assessment; it is a reported build example, not proof that the same package fits another car.
In its 8 October 2026 customer-build feature, Emtron describes the owner of a 2JZ-powered Toyota 86 with an 8HP70 moving to a KV8 engine ECU, TM16 and ED7 display. This is a manufacturer feature describing a conversion in progress, not an independent completed-installation report. Check the individual gearbox, modified mechatronics and engine torque integration against the current Emtron instructions. Sources reviewed 17 November 2026.
Revision 3: Emtron TM16 for ZF 8HP
The Emtron TM16 is a programmable external transmission control module. It can be configured for a ZF 8HP using Emtron's documented 8HP setup. The factory TCM is bypassed in that setup, so it is not interchangeable with systems retaining the unmodified factory controller. Emtron TM16 datasheet and product photograph; Emtron ZF 8HP guide.
Emtron TM16 transmission controller. Image and credit: Emtron Australia. Permission to republish confirmed by the user.
Identification and compatibility
Identify the module as TM16 and record hardware and firmware versions, the transmission plate and mechatronic part numbers, connector and valve-body configuration. The datasheet lists three mating connectors: A 4-1437290-0, B 4-1437290-1 and C 3-1437290-7. TMtune is used for configuration. The 8HP base calibration is based on 8HP70 and is a starting point requiring setup for the actual installation.
Emtron's 8HP guide lists 8HP45, 50, 70, 75, 90 and 95 as supported. It marks 8HP51 and 76 as requiring a Gen 2 valve body. Only gearboxes with 16-pin connectors are supported in this setup; the guide says 10-pin versions lack the necessary inputs and outputs. Confirm the exact assembly and current requirements with Emtron before buying or modifying it.
TM16 controller pinout
The following is the controller-side pin assignment from the Emtron TM16 datasheet, which depicts the view looking into the TCM. Names below are the manufacturer's hardware functions, not fixed 8HP wiring assignments. Use the datasheet connector drawing and power supply guidance for fusing, supply, grounding and output-bank requirements. Inputs and outputs must agree with the actual calibration.
Connector A
Pin
Function
A1
ANV 1
A2
ANV 2
A3
ANV 3
A4
ANV 4
A5
ANV 5
A6
ANV 6
A7
ANV 7
A8
ANV 8
A9
Sensor 0V Ref
A10
ANV 9
A11
ANV 10
A12
ANV 11
A13
ANV 12
A14
ANV 13
A15
ANV 14
A16
ANV 15
A17
ANV 16
A18
DI 1
A19
DI 2
A20
DI 3
A21
DI 4
A22
DI 5
A23
DI 6
A24
DI 7
A25
DI 8
A26
DI 9
A27
DI 10
A28
DI 11
A29
DI 12
A30
DI 13
A31
DI 14
A32
DI 15
A33
DI 16
A34
Sensor 0V Ref
Connector B
Pin
Function
B1
Aux 1
B2
Aux 2
B3
Aux 3
B4
Aux 4
B5
Aux 5
B6
Aux 6
B7
Aux 7
B8
Aux 8
B9
GND
B10
Solenoid 1
B11
Solenoid 2
B12
Solenoid 3
B13
Solenoid 4
B14
Solenoid 5
B15
Solenoid 6
B16
Solenoid 7
B17
Solenoid 8
B18
Solenoid 9
B19
Solenoid 10
B20
Solenoid 11
B21
Solenoid 12
B22
Solenoid 13
B23
Solenoid 14
B24
Solenoid 15
B25
Solenoid 16
B26
Analog Out 1
B27
Analog Out 2
B28
Analog Out 3
B29
Analog Out 4
B30
Solenoid 1-4 Supply Output
B31
Solenoid 5-8 Supply Output
B32
Solenoid 9-12 Supply Output
B33
Solenoid 13-16 Supply Output
B34
GND
Connector C
Pin
Function
C1
Battery Hot Supply
C2
Aux 1-4 Supply
C3
Aux 5-8 Supply
C4
Solenoid 1-8 Supply
C5
Solenoid 9-16 Supply
C6
Ignition Switch
C7
GND
C8
CAN 1 Hi
C9
CAN 2 Hi
C10
Hall 1
C11
Hall 2
C12
Hall 3
C13
Hall 4
C14
CAN 1 Lo
C15
CAN 2 Lo
C16
5V0 Ref Output 1
C17
5V0 Ref Output 2
C18
8V0 Ref Output
C19
Sensor 0V Ref
C20
Ethernet Rx+
C21
Ethernet Rx-
C22
Ethernet Tx+
C23
Ethernet Tx-
C24
RS232 Rx
C25
RS232 Tx
C26
GND
8HP-specific wiring and identification
The manufacturer's 8HP instructions show the internal bypass, the transmission connector view, base-calibration wiring and Gen 1/Gen 2 solenoid differences. These connections apply only after the specified mechatronic modifications, not to a standard factory TCU. The source's table labels one Gen 2 entry as pin 17, while its accompanying note says swap pins 15 and 16; confirm the discrepancy with Emtron and the numbered connector before wiring. Do not infer the missing assignment.
Emtron specifies digital inputs rather than the dedicated Hall inputs for the 8HP speed sensors and requires the appropriate pulldown and thresholds. Verify sensor signals, solenoid assignments and current-control calibration for the exact gearbox. The Emtron ECU integration guide documents CAN and engine-torque coordination for its ECU.
Engine Swap Depot's September 2026 feature describes a Mach1 Motorsport BMW E30 with a turbo Mitsubishi 4G63, an adapter, an 8HP70 and an Emtron TM16. The article identifies the parts but does not provide a wiring diagram, calibration or detailed driving assessment; it is a reported build example, not proof that the same package fits another car.
In its 8 October 2026 customer-build feature, Emtron describes the owner of a 2JZ-powered Toyota 86 with an 8HP70 moving to a KV8 engine ECU, TM16 and ED7 display. This is a manufacturer feature describing a conversion in progress, not an independent completed-installation report. Check the individual gearbox, modified mechatronics and engine torque integration against the current Emtron instructions. Sources reviewed 17 November 2026.