
Some first-generation ZF 8HP transmissions use an original mechatronic transmission control module (TCM/TCU) with Bosch identification numbers. BMW also uses the term EGS for electronic transmission control. This page is an identification guide for the specific examples cited below; it is not a universal Bosch part-number, firmware or interchange list for all 8HP transmissions.
In the documented Porsche 8HP65AX application, the electronic TCU and hydraulic control unit form one mechatronic assembly inside the gearbox; individual sensors and pressure-control components are part of that described assembly. The Porsche system description is an example of the architecture and does not establish the manufacturer or pinout of all GEN1 units. See ZF 8HP gearbox controllers for the wider family.
Find the identification
- Record the transmission type and full suffix, catalogue or specification number, transmission serial number, donor VIN and vehicle. The ZF 2018 remanufactured transmission catalogue, figure 2, shows where the catalogue number, type and OE control-module hardware number can appear on an example 6HP/8HP label.
- Record the mechatronic part number and the electronically read TCU identification, hardware and software information. ZF’s 8HP mechatronic service information directs kit selection by the mechatronic part number; transmission designation is additional guidance.
- Distinguish the Bosch part number from the Bosch TCU ID. MaxxECU’s 8HP installation page illustrates both labels and lists reported ID, part number, CPU family, gearbox and example donor together. Compare all available identifiers with the exact application and supplier’s instructions.
Documented example Bosch identifiers
MaxxECU’s TCU support table lists these examples with SH725xx CPU designation. Its support status refers to the aftermarket MaxxECU firmware, not to factory interchangeability or an OE parts supersession. A repeated TCU ID does not prove that all hardware, software, immobiliser and gearbox combinations are interchangeable.
| Reported Bosch TCU ID | Reported Bosch part number | Gearbox and donor in supplier table |
|---|---|---|
| 1034420221 | 0260550075 | 8HP70, BMW E70 X5 4.4, 2013 |
| 1034420235 | Not specified in this row | 8HP45, BMW 335i N55 |
| 1034420236 | 0260550074 | 8HP70, BMW 5 F10/F11 |
| 1034420237 | 0260550076 | 8HP70, Jaguar XF CC9 2.2 diesel, 2015 |
| 1034420267 | Not specified in these rows | 8HP70, Dodge Charger 2018; 8HP90, Dodge Challenger Hellcat 2016 |
| 1034420285 | Not specified in this row | 8HP70, VW Amarok 2016 |
| 1034420288 | 0260550074 | 8HP70, Dodge RAM Classic 5.7 RWD, 2020 |
Preserve the distinction between an identifier read from a control unit and an OE or ZF number on a label. The table does not identify a distinct connector pinout for each listed ID; source-specific electrical data must be checked for the actual donor and TCU.
Example connector: Dodge GEN1 8HP as documented for MaxxECU
MaxxECU’s installation and wiring manual gives the following assignments for the Dodge 8HP GEN1 transmission connector. Its diagram is viewed looking into the connector’s terminal side. The supplier does not associate this table with every Bosch ID or model year above. Verify the connector and cavity markings against the vehicle wiring information and supplier’s diagram before applying power; this table does not establish a pinout for BMW, Jaguar, Audi or other variants.
| Cavity | MaxxECU’s documented function |
|---|---|
| 5 | CAN High |
| 6 | CAN Low |
| 9 | +12 V wake-up |
| 13 | +12 V main supply |
| 14 | Ground |
Other cavities are shown with dashes in that table; do not assume they are unused in an OE vehicle. For its own reflash/control installation MaxxECU says main power should be active continuously or for at least 10–15 seconds before wake-up, and notes the 8HP TCU has no built-in CAN termination. The complete installation instructions and the applicable OE wiring diagram take precedence. This is not a programming, bypass-board or universal 8HP connection guide.
Factory vehicle matching
BMW’s service bulletin B24 03 15 covers BMW vehicles with ZF 6HP/8HP and EWS4. It says the programmed mechatronic is paired with the DME and CAS for the specific VIN and warns that an unmatched used unit can prevent gear selection. That statement is scoped to the BMW EWS4 vehicles in the bulletin; it does not establish the security procedure of another make or every 8HP.
Images and related information
The MaxxECU illustrated manual shows examples of Bosch part-number and TCU-ID labels, the transmission connector and its terminal view. The ZF catalogue includes transmission plate identification images. Images remain at their original sites; credits: MaxxECU and ZF.
For MaxxECU-specific reflashing and harness details see MaxxECU ZF 8HP transmission control. See ZF 8HP gearbox types for assembly identification. Sources reviewed 17 November 2026.