Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Gearboxes
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 3

Removed text is struck through; added text is highlighted.

The Emtron TM16 is a programmable external transmission control module. It can be configured for a ZF 8HP using Emtron's documented 8HP setup. The factory TCM is bypassed in that setup, so it is not interchangeable with systems retaining the unmodified factory controller. Emtron TM16 datasheet and product photograph; Emtron ZF 8HP guide.

Emtron TM16 transmission controller. Image and credit: Emtron Australia. Permission to republish confirmed by the user.

Identification and compatibility

Identify the module as TM16 and record hardware and firmware versions, the transmission plate and mechatronic part numbers, connector and valve-body configuration. The datasheet lists three mating connectors: A 4-1437290-0, B 4-1437290-1 and C 3-1437290-7. TMtune is used for configuration. The 8HP base calibration is based on 8HP70 and is a starting point requiring setup for the actual installation.

Emtron's 8HP guide lists 8HP45, 50, 70, 75, 90 and 95 as supported. It marks 8HP51 and 76 as requiring a Gen 2 valve body. Only gearboxes with 16-pin connectors are supported in this setup; the guide says 10-pin versions lack the necessary inputs and outputs. Confirm the exact assembly and current requirements with Emtron before buying or modifying it.

TM16 controller pinout

The following is the controller-side pin assignment from the Emtron TM16 datasheet, which depicts the view looking into the TCM. Names below are the manufacturer's hardware functions, not fixed 8HP wiring assignments. Use the datasheet connector drawing and power supply guidance for fusing, supply, grounding and output-bank requirements. Inputs and outputs must agree with the actual calibration.

Connector A

PinFunctionA1ANV 1A2ANV 2A3ANV 3A4ANV 4A5ANV 5A6ANV 6A7ANV 7A8ANV 8A9Sensor 0V RefA10ANV 9A11ANV 10A12ANV 11A13ANV 12A14ANV 13A15ANV 14A16ANV 15A17ANV 16A18DI 1A19DI 2A20DI 3A21DI 4A22DI 5A23DI 6A24DI 7A25DI 8A26DI 9A27DI 10A28DI 11A29DI 12A30DI 13A31DI 14A32DI 15A33DI 16A34Sensor 0V Ref

Connector B

PinFunctionB1Aux 1B2Aux 2B3Aux 3B4Aux 4B5Aux 5B6Aux 6B7Aux 7B8Aux 8B9GNDB10Solenoid 1B11Solenoid 2B12Solenoid 3B13Solenoid 4B14Solenoid 5B15Solenoid 6B16Solenoid 7B17Solenoid 8B18Solenoid 9B19Solenoid 10B20Solenoid 11B21Solenoid 12B22Solenoid 13B23Solenoid 14B24Solenoid 15B25Solenoid 16B26Analog Out 1B27Analog Out 2B28Analog Out 3B29Analog Out 4B30Solenoid 1-4 Supply OutputB31Solenoid 5-8 Supply OutputB32Solenoid 9-12 Supply OutputB33Solenoid 13-16 Supply OutputB34GND

Connector C

PinFunctionC1Battery Hot SupplyC2Aux 1-4 SupplyC3Aux 5-8 SupplyC4Solenoid 1-8 SupplyC5Solenoid 9-16 SupplyC6Ignition SwitchC7GNDC8CAN 1 HiC9CAN 2 HiC10Hall 1C11Hall 2C12Hall 3C13Hall 4C14CAN 1 LoC15CAN 2 LoC165V0 Ref Output 1C175V0 Ref Output 2C188V0 Ref OutputC19Sensor 0V RefC20Ethernet Rx+C21Ethernet Rx-C22Ethernet Tx+C23Ethernet Tx-C24RS232 RxC25RS232 TxC26GND

8HP-specific wiring and identification

The manufacturer's 8HP instructions show the internal bypass, the transmission connector view, base-calibration wiring and Gen 1/Gen 2 solenoid differences. These connections apply only after the specified mechatronic modifications, not to a standard factory TCU. The source's table labels one Gen 2 entry as pin 17, while its accompanying note says swap pins 15 and 16; confirm the discrepancy with Emtron and the numbered connector before wiring. Do not infer the missing assignment.

Emtron specifies digital inputs rather than the dedicated Hall inputs for the 8HP speed sensors and requires the appropriate pulldown and thresholds. Verify sensor signals, solenoid assignments and current-control calibration for the exact gearbox. The Emtron ECU integration guide documents CAN and engine-torque coordination for its ECU.

See ZF 8HP gearbox controllers and ZF 8HP gearbox types. Sources reviewed 17 November 2026.

Published build examplesEngine Swap Depot's September 2026 feature describes a Mach1 Motorsport BMW E30 with a turbo Mitsubishi 4G63, an adapter, an 8HP70 and an Emtron TM16. The article identifies the parts but does not provide a wiring diagram, calibration or detailed driving assessment; it is a reported build example, not proof that the same package fits another car.In its 8 October 2026 customer-build feature, Emtron describes the owner of a 2JZ-powered Toyota 86 with an 8HP70 moving to a KV8 engine ECU, TM16 and ED7 display. This is a manufacturer feature describing a conversion in progress, not an independent completed-installation report. Check the individual gearbox, modified mechatronics and engine torque integration against the current Emtron instructions. Sources reviewed 17 November 2026.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Emtron TM16 for ZF 8HP

The Emtron TM16 is a programmable external transmission control module. It can be configured for a ZF 8HP using Emtron's documented 8HP setup. The factory TCM is bypassed in that setup, so it is not interchangeable with systems retaining the unmodified factory controller. Emtron TM16 datasheet and product photograph; Emtron ZF 8HP guide.

Identification and compatibility

Identify the module as TM16 and record hardware and firmware versions, the transmission plate and mechatronic part numbers, connector and valve-body configuration. The datasheet lists three mating connectors: A 4-1437290-0, B 4-1437290-1 and C 3-1437290-7. TMtune is used for configuration. The 8HP base calibration is based on 8HP70 and is a starting point requiring setup for the actual installation.

Emtron's 8HP guide lists 8HP45, 50, 70, 75, 90 and 95 as supported. It marks 8HP51 and 76 as requiring a Gen 2 valve body. Only gearboxes with 16-pin connectors are supported in this setup; the guide says 10-pin versions lack the necessary inputs and outputs. Confirm the exact assembly and current requirements with Emtron before buying or modifying it.

TM16 controller pinout

The following is the controller-side pin assignment from the Emtron TM16 datasheet, which depicts the view looking into the TCM. Names below are the manufacturer's hardware functions, not fixed 8HP wiring assignments. Use the datasheet connector drawing and power supply guidance for fusing, supply, grounding and output-bank requirements. Inputs and outputs must agree with the actual calibration.

Connector A

PinFunction
A1ANV 1
A2ANV 2
A3ANV 3
A4ANV 4
A5ANV 5
A6ANV 6
A7ANV 7
A8ANV 8
A9Sensor 0V Ref
A10ANV 9
A11ANV 10
A12ANV 11
A13ANV 12
A14ANV 13
A15ANV 14
A16ANV 15
A17ANV 16
A18DI 1
A19DI 2
A20DI 3
A21DI 4
A22DI 5
A23DI 6
A24DI 7
A25DI 8
A26DI 9
A27DI 10
A28DI 11
A29DI 12
A30DI 13
A31DI 14
A32DI 15
A33DI 16
A34Sensor 0V Ref

Connector B

PinFunction
B1Aux 1
B2Aux 2
B3Aux 3
B4Aux 4
B5Aux 5
B6Aux 6
B7Aux 7
B8Aux 8
B9GND
B10Solenoid 1
B11Solenoid 2
B12Solenoid 3
B13Solenoid 4
B14Solenoid 5
B15Solenoid 6
B16Solenoid 7
B17Solenoid 8
B18Solenoid 9
B19Solenoid 10
B20Solenoid 11
B21Solenoid 12
B22Solenoid 13
B23Solenoid 14
B24Solenoid 15
B25Solenoid 16
B26Analog Out 1
B27Analog Out 2
B28Analog Out 3
B29Analog Out 4
B30Solenoid 1-4 Supply Output
B31Solenoid 5-8 Supply Output
B32Solenoid 9-12 Supply Output
B33Solenoid 13-16 Supply Output
B34GND

Connector C

PinFunction
C1Battery Hot Supply
C2Aux 1-4 Supply
C3Aux 5-8 Supply
C4Solenoid 1-8 Supply
C5Solenoid 9-16 Supply
C6Ignition Switch
C7GND
C8CAN 1 Hi
C9CAN 2 Hi
C10Hall 1
C11Hall 2
C12Hall 3
C13Hall 4
C14CAN 1 Lo
C15CAN 2 Lo
C165V0 Ref Output 1
C175V0 Ref Output 2
C188V0 Ref Output
C19Sensor 0V Ref
C20Ethernet Rx+
C21Ethernet Rx-
C22Ethernet Tx+
C23Ethernet Tx-
C24RS232 Rx
C25RS232 Tx
C26GND

8HP-specific wiring and identification

The manufacturer's 8HP instructions show the internal bypass, the transmission connector view, base-calibration wiring and Gen 1/Gen 2 solenoid differences. These connections apply only after the specified mechatronic modifications, not to a standard factory TCU. The source's table labels one Gen 2 entry as pin 17, while its accompanying note says swap pins 15 and 16; confirm the discrepancy with Emtron and the numbered connector before wiring. Do not infer the missing assignment.

Emtron specifies digital inputs rather than the dedicated Hall inputs for the 8HP speed sensors and requires the appropriate pulldown and thresholds. Verify sensor signals, solenoid assignments and current-control calibration for the exact gearbox. The Emtron ECU integration guide documents CAN and engine-torque coordination for its ECU.

See ZF 8HP gearbox controllers and ZF 8HP gearbox types. Sources reviewed 17 November 2026.

Revision 3: Emtron TM16 for ZF 8HP

The Emtron TM16 is a programmable external transmission control module. It can be configured for a ZF 8HP using Emtron's documented 8HP setup. The factory TCM is bypassed in that setup, so it is not interchangeable with systems retaining the unmodified factory controller. Emtron TM16 datasheet and product photograph; Emtron ZF 8HP guide.

Emtron TM16 transmission controller
Emtron TM16 transmission controller. Image and credit: Emtron Australia. Permission to republish confirmed by the user.

Identification and compatibility

Identify the module as TM16 and record hardware and firmware versions, the transmission plate and mechatronic part numbers, connector and valve-body configuration. The datasheet lists three mating connectors: A 4-1437290-0, B 4-1437290-1 and C 3-1437290-7. TMtune is used for configuration. The 8HP base calibration is based on 8HP70 and is a starting point requiring setup for the actual installation.

Emtron's 8HP guide lists 8HP45, 50, 70, 75, 90 and 95 as supported. It marks 8HP51 and 76 as requiring a Gen 2 valve body. Only gearboxes with 16-pin connectors are supported in this setup; the guide says 10-pin versions lack the necessary inputs and outputs. Confirm the exact assembly and current requirements with Emtron before buying or modifying it.

TM16 controller pinout

The following is the controller-side pin assignment from the Emtron TM16 datasheet, which depicts the view looking into the TCM. Names below are the manufacturer's hardware functions, not fixed 8HP wiring assignments. Use the datasheet connector drawing and power supply guidance for fusing, supply, grounding and output-bank requirements. Inputs and outputs must agree with the actual calibration.

Connector A

PinFunction
A1ANV 1
A2ANV 2
A3ANV 3
A4ANV 4
A5ANV 5
A6ANV 6
A7ANV 7
A8ANV 8
A9Sensor 0V Ref
A10ANV 9
A11ANV 10
A12ANV 11
A13ANV 12
A14ANV 13
A15ANV 14
A16ANV 15
A17ANV 16
A18DI 1
A19DI 2
A20DI 3
A21DI 4
A22DI 5
A23DI 6
A24DI 7
A25DI 8
A26DI 9
A27DI 10
A28DI 11
A29DI 12
A30DI 13
A31DI 14
A32DI 15
A33DI 16
A34Sensor 0V Ref

Connector B

PinFunction
B1Aux 1
B2Aux 2
B3Aux 3
B4Aux 4
B5Aux 5
B6Aux 6
B7Aux 7
B8Aux 8
B9GND
B10Solenoid 1
B11Solenoid 2
B12Solenoid 3
B13Solenoid 4
B14Solenoid 5
B15Solenoid 6
B16Solenoid 7
B17Solenoid 8
B18Solenoid 9
B19Solenoid 10
B20Solenoid 11
B21Solenoid 12
B22Solenoid 13
B23Solenoid 14
B24Solenoid 15
B25Solenoid 16
B26Analog Out 1
B27Analog Out 2
B28Analog Out 3
B29Analog Out 4
B30Solenoid 1-4 Supply Output
B31Solenoid 5-8 Supply Output
B32Solenoid 9-12 Supply Output
B33Solenoid 13-16 Supply Output
B34GND

Connector C

PinFunction
C1Battery Hot Supply
C2Aux 1-4 Supply
C3Aux 5-8 Supply
C4Solenoid 1-8 Supply
C5Solenoid 9-16 Supply
C6Ignition Switch
C7GND
C8CAN 1 Hi
C9CAN 2 Hi
C10Hall 1
C11Hall 2
C12Hall 3
C13Hall 4
C14CAN 1 Lo
C15CAN 2 Lo
C165V0 Ref Output 1
C175V0 Ref Output 2
C188V0 Ref Output
C19Sensor 0V Ref
C20Ethernet Rx+
C21Ethernet Rx-
C22Ethernet Tx+
C23Ethernet Tx-
C24RS232 Rx
C25RS232 Tx
C26GND

8HP-specific wiring and identification

The manufacturer's 8HP instructions show the internal bypass, the transmission connector view, base-calibration wiring and Gen 1/Gen 2 solenoid differences. These connections apply only after the specified mechatronic modifications, not to a standard factory TCU. The source's table labels one Gen 2 entry as pin 17, while its accompanying note says swap pins 15 and 16; confirm the discrepancy with Emtron and the numbered connector before wiring. Do not infer the missing assignment.

Emtron specifies digital inputs rather than the dedicated Hall inputs for the 8HP speed sensors and requires the appropriate pulldown and thresholds. Verify sensor signals, solenoid assignments and current-control calibration for the exact gearbox. The Emtron ECU integration guide documents CAN and engine-torque coordination for its ECU.

See ZF 8HP gearbox controllers and ZF 8HP gearbox types. Sources reviewed 17 November 2026.

Published build examples

Engine Swap Depot's September 2026 feature describes a Mach1 Motorsport BMW E30 with a turbo Mitsubishi 4G63, an adapter, an 8HP70 and an Emtron TM16. The article identifies the parts but does not provide a wiring diagram, calibration or detailed driving assessment; it is a reported build example, not proof that the same package fits another car.

In its 8 October 2026 customer-build feature, Emtron describes the owner of a 2JZ-powered Toyota 86 with an 8HP70 moving to a KV8 engine ECU, TM16 and ED7 display. This is a manufacturer feature describing a conversion in progress, not an independent completed-installation report. Check the individual gearbox, modified mechatronics and engine torque integration against the current Emtron instructions. Sources reviewed 17 November 2026.