Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Manifold pressure
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
NXP

Changes from revision 1 to revision 1

Removed text is struck through; added text is highlighted.

The element, not the vehicle part

The MPX series is a silicon absolute-pressure element with the amplifier and the temperature compensation on the chip. NXP’s datasheets, earlier published by Freescale and before that by Motorola, print the transfer function. A vehicle sensor from Bosch, Denso or Delphi is a calibrated housing around some maker’s die. Use the MPX equation for an MPX part, or for a housing whose maker says it is that die with no further calibration. Do not use it for a Bosch part number whose own curve is on Bosch absolute-pressure sensors.

All three below are absolute. P is kilopascals. The output is ratiometric with the supply VS written in the formula. The error band below is the datasheet’s pressure error from 0 to 85 °C. Outside that, a temperature multiplier widens it, out to the −40 to +125 °C operating limit.

MPX4115A

15 to 115 kPa. This is the naturally aspirated and barometer range. Supply 5.1 V ± 0.25 V. Supply current is typically 7 mA and not more than 10 mA. Sensitivity is 45.9 mV/kPa at the 5.1 V supply. Response time is typically 1 ms, and the warm-up time is typically 20 ms. The maximum pressure is 400 kPa. The pressure error from 0 to 85 °C is ±1.5 kPa.

Vout = VS × (0.009 × P − 0.095), with VS = 5.1 V.

At 5.1 V the nominal points are 0.204 V at 15 kPa, 1.811 V at 50 kPa, 4.106 V at 100 kPa and 4.794 V at 115 kPa. The datasheet’s own offset window at 15 kPa is 0.135 to 0.273 V, typical 0.204 V, and the full-scale window at 115 kPa is 4.725 to 4.863 V, typical 4.794 V.

MPX4250A

20 to 250 kPa. This is the range used where the manifold can see something over 1 bar absolute, up to 2.5 bar. Supply 5.1 V ± 0.25 V. The pressure error from 0 to 85 °C is ±3.45 kPa.

Vout = VS × (0.004 × P − 0.04), with VS = 5.1 V.

At 5.1 V the nominal points are 0.204 V at 20 kPa, 1.836 V at 100 kPa, 3.876 V at 200 kPa and 4.896 V at 250 kPa.

MPXH6400A

20 to 400 kPa. This is the 4 bar absolute element, in the small outline package. Supply 5.0 V, with the transfer function specified at 5.0 V ± 0.36 V. Supply current is typically 6 mA and not more than 10 mA. Sensitivity is 12.1 mV/kPa. Response time is typically 1 ms. The maximum pressure is 1600 kPa. The pressure error from 0 to 85 °C is ±5.5 kPa.

Vout = VS × (0.002421 × P − 0.00842), with VS = 5.0 V.

At 5.0 V the nominal points are 0.200 V at 20 kPa, 1.168 V at 100 kPa, 2.379 V at 200 kPa, 3.589 V at 300 kPa and 4.800 V at 400 kPa. The datasheet’s typical offset at 20 kPa is 0.2 V and the typical full-scale output at 400 kPa is 4.8 V.

Using the equation

The formulas already include the supply. Putting in 5.00 V when the datasheet was written at 5.10 V moves the MPX4115 and MPX4250 readings by 5.1/5.0, about 2 %. Measure the supply at the sensor and use that value as VS.

A reading can sit inside 0.2 to 4.9 V and still be the wrong pressure if the equation belongs to the other die. At a true 100 kPa and a 5.1 V supply, the MPX4115 is at 4.11 V and the MPX4250 is at 1.84 V. Both are healthy voltages. They are not the same sensor. The overview of how a control unit uses the result is on manifold and boost pressure sensors.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: NXP MPX absolute pressure sensors

The element, not the vehicle part

The MPX series is a silicon absolute-pressure element with the amplifier and the temperature compensation on the chip. NXP’s datasheets, earlier published by Freescale and before that by Motorola, print the transfer function. A vehicle sensor from Bosch, Denso or Delphi is a calibrated housing around some maker’s die. Use the MPX equation for an MPX part, or for a housing whose maker says it is that die with no further calibration. Do not use it for a Bosch part number whose own curve is on Bosch absolute-pressure sensors.

All three below are absolute. P is kilopascals. The output is ratiometric with the supply VS written in the formula. The error band below is the datasheet’s pressure error from 0 to 85 °C. Outside that, a temperature multiplier widens it, out to the −40 to +125 °C operating limit.

MPX4115A

15 to 115 kPa. This is the naturally aspirated and barometer range. Supply 5.1 V ± 0.25 V. Supply current is typically 7 mA and not more than 10 mA. Sensitivity is 45.9 mV/kPa at the 5.1 V supply. Response time is typically 1 ms, and the warm-up time is typically 20 ms. The maximum pressure is 400 kPa. The pressure error from 0 to 85 °C is ±1.5 kPa.

Vout = VS × (0.009 × P − 0.095), with VS = 5.1 V.

At 5.1 V the nominal points are 0.204 V at 15 kPa, 1.811 V at 50 kPa, 4.106 V at 100 kPa and 4.794 V at 115 kPa. The datasheet’s own offset window at 15 kPa is 0.135 to 0.273 V, typical 0.204 V, and the full-scale window at 115 kPa is 4.725 to 4.863 V, typical 4.794 V.

MPX4250A

20 to 250 kPa. This is the range used where the manifold can see something over 1 bar absolute, up to 2.5 bar. Supply 5.1 V ± 0.25 V. The pressure error from 0 to 85 °C is ±3.45 kPa.

Vout = VS × (0.004 × P − 0.04), with VS = 5.1 V.

At 5.1 V the nominal points are 0.204 V at 20 kPa, 1.836 V at 100 kPa, 3.876 V at 200 kPa and 4.896 V at 250 kPa.

MPXH6400A

20 to 400 kPa. This is the 4 bar absolute element, in the small outline package. Supply 5.0 V, with the transfer function specified at 5.0 V ± 0.36 V. Supply current is typically 6 mA and not more than 10 mA. Sensitivity is 12.1 mV/kPa. Response time is typically 1 ms. The maximum pressure is 1600 kPa. The pressure error from 0 to 85 °C is ±5.5 kPa.

Vout = VS × (0.002421 × P − 0.00842), with VS = 5.0 V.

At 5.0 V the nominal points are 0.200 V at 20 kPa, 1.168 V at 100 kPa, 2.379 V at 200 kPa, 3.589 V at 300 kPa and 4.800 V at 400 kPa. The datasheet’s typical offset at 20 kPa is 0.2 V and the typical full-scale output at 400 kPa is 4.8 V.

Using the equation

The formulas already include the supply. Putting in 5.00 V when the datasheet was written at 5.10 V moves the MPX4115 and MPX4250 readings by 5.1/5.0, about 2 %. Measure the supply at the sensor and use that value as VS.

A reading can sit inside 0.2 to 4.9 V and still be the wrong pressure if the equation belongs to the other die. At a true 100 kPa and a 5.1 V supply, the MPX4115 is at 4.11 V and the MPX4250 is at 1.84 V. Both are healthy voltages. They are not the same sensor. The overview of how a control unit uses the result is on manifold and boost pressure sensors.

Revision 1: NXP MPX absolute pressure sensors

The element, not the vehicle part

The MPX series is a silicon absolute-pressure element with the amplifier and the temperature compensation on the chip. NXP’s datasheets, earlier published by Freescale and before that by Motorola, print the transfer function. A vehicle sensor from Bosch, Denso or Delphi is a calibrated housing around some maker’s die. Use the MPX equation for an MPX part, or for a housing whose maker says it is that die with no further calibration. Do not use it for a Bosch part number whose own curve is on Bosch absolute-pressure sensors.

All three below are absolute. P is kilopascals. The output is ratiometric with the supply VS written in the formula. The error band below is the datasheet’s pressure error from 0 to 85 °C. Outside that, a temperature multiplier widens it, out to the −40 to +125 °C operating limit.

MPX4115A

15 to 115 kPa. This is the naturally aspirated and barometer range. Supply 5.1 V ± 0.25 V. Supply current is typically 7 mA and not more than 10 mA. Sensitivity is 45.9 mV/kPa at the 5.1 V supply. Response time is typically 1 ms, and the warm-up time is typically 20 ms. The maximum pressure is 400 kPa. The pressure error from 0 to 85 °C is ±1.5 kPa.

Vout = VS × (0.009 × P − 0.095), with VS = 5.1 V.

At 5.1 V the nominal points are 0.204 V at 15 kPa, 1.811 V at 50 kPa, 4.106 V at 100 kPa and 4.794 V at 115 kPa. The datasheet’s own offset window at 15 kPa is 0.135 to 0.273 V, typical 0.204 V, and the full-scale window at 115 kPa is 4.725 to 4.863 V, typical 4.794 V.

MPX4250A

20 to 250 kPa. This is the range used where the manifold can see something over 1 bar absolute, up to 2.5 bar. Supply 5.1 V ± 0.25 V. The pressure error from 0 to 85 °C is ±3.45 kPa.

Vout = VS × (0.004 × P − 0.04), with VS = 5.1 V.

At 5.1 V the nominal points are 0.204 V at 20 kPa, 1.836 V at 100 kPa, 3.876 V at 200 kPa and 4.896 V at 250 kPa.

MPXH6400A

20 to 400 kPa. This is the 4 bar absolute element, in the small outline package. Supply 5.0 V, with the transfer function specified at 5.0 V ± 0.36 V. Supply current is typically 6 mA and not more than 10 mA. Sensitivity is 12.1 mV/kPa. Response time is typically 1 ms. The maximum pressure is 1600 kPa. The pressure error from 0 to 85 °C is ±5.5 kPa.

Vout = VS × (0.002421 × P − 0.00842), with VS = 5.0 V.

At 5.0 V the nominal points are 0.200 V at 20 kPa, 1.168 V at 100 kPa, 2.379 V at 200 kPa, 3.589 V at 300 kPa and 4.800 V at 400 kPa. The datasheet’s typical offset at 20 kPa is 0.2 V and the typical full-scale output at 400 kPa is 4.8 V.

Using the equation

The formulas already include the supply. Putting in 5.00 V when the datasheet was written at 5.10 V moves the MPX4115 and MPX4250 readings by 5.1/5.0, about 2 %. Measure the supply at the sensor and use that value as VS.

A reading can sit inside 0.2 to 4.9 V and still be the wrong pressure if the equation belongs to the other die. At a true 100 kPa and a 5.1 V supply, the MPX4115 is at 4.11 V and the MPX4250 is at 1.84 V. Both are healthy voltages. They are not the same sensor. The overview of how a control unit uses the result is on manifold and boost pressure sensors.