Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Manifold pressure
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Ford

A frequency, not a voltage

On EEC-IV the manifold absolute pressure sensor and the barometric pressure sensor are a piezoelectric disc that changes frequency. The frequency rises as manifold vacuum falls. At a wide-open throttle, or with the engine stopped, the sensor is near its highest frequency. At a closed throttle it is near its lowest. A DC voltmeter on the signal wire will not read the pressure. The measurement is hertz, with a meter that can count a 5 V square wave, or with the MAP/BARO tester the pinpoint test calls for.

The sensor base number in the circuit test is 9F479. The control unit reads it on three pins of the 60-pin connector: pin 26 is VREF, pin 45 is the signal, pin 46 is signal return. The frequency also sets fuelling, spark, EGR and the altitude correction. A kinked vacuum hose, a mechanical engine fault and an unusual barometer are on the test’s own list of causes that are outside the sensor.

This is not the analogue sensor used on later Ford engines. A three-pin Siemens sensor on a Fiesta or a Focus is a voltage sensor. Its part numbers are on manifold pressure sensor manufacturers.

Vacuum against frequency

The pinpoint table is manifold vacuum, not absolute pressure. It is written for a barometer of 30.0 in-Hg. Absolute pressure is that barometer minus the vacuum. At 0 in-Hg of vacuum the absolute pressure is the barometer, and the frequency is 159 Hz. At 30 in-Hg of vacuum the absolute pressure is near zero and the frequency is 80 Hz. The kilopascal column is the vacuum as well.

Manifold vacuum, in-HgVacuum, kPaFrequency, Hz
00159
310.2150
620.3141
930.5133
1240.6125
1550.8117
1861.0109
2171.1102
2481.395
2791.588
30101.680

The same test allows ±3 Hz for sensor variation. A reading 3 Hz low is still the table. A reading that does not move when a vacuum pump is put on the port is a hose, a sensor, or the wiring, and the pinpoint separates those.

Key-on barometer

With the key on and the engine stopped, the MAP sensor is reading the atmosphere, and a separate BARO sensor is doing the same job all the time. The frequency in this table is absolute barometric pressure. It is the check that does not need a vacuum pump. At about 30 in-Hg it meets the 159 Hz line above.

Barometer, in-HgkPaFrequency, Hz
17.158122.4
18.362125.5
19.566128.7
20.770131.9
21.874135.1
23.078138.3
24.282141.8
25.486145.4
26.690148.9
27.794152.5
28.998156.1
30.1102159.6
31.0105162.4

The same ±3 Hz note applies. A sensor that reads 156 Hz at the coast and 159 Hz in the table is inside the tolerance if the local barometer is the cause. The test says to suspect an unusual barometer before the sensor.

Pins and colours

Colours in the EEC-IV pinpoint are not one set for every vehicle. The test pins are. Pin 26 is the 5 V reference, pin 45 is the signal, pin 46 is the signal return.

PinFunctionColour in that pinpoint
26VREFRed on 7.0 L F-Series. Brown/white on the other applications in the table.
45MAP/BARO signalBlue/green on 7.0 L F-Series. Dark blue/light green on 3.8 L Thunderbird SC and 5.0 L SFI E-Series. Light green/black on the others.
46Signal returnBlack/white on 7.0 L F-Series. Gray/red on the others.

A different model year can use a different colour on the same pin. The connector end is identified by the vacuum port: in the bench test written around this sensor, the wire closest to the port is the reference input, the middle wire is the signal, and the wire furthest from the port is the return. Confirm that against the pin numbers before using it on a sensor whose shell is not the one that test was written for.

A BARO sensor used with a vane airflow meter is the same kind of part, often identified by a collar. It is not an airflow meter, and it is not the ratiometric Bosch sensor on Bosch absolute-pressure sensors.