Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Manifold pressure
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Bosch, Denso, Ford, Siemens

Changes from revision 1 to revision 1

Removed text is struck through; added text is highlighted.

The same job, several makers

The car maker specifies the range, the plug and the place in the intake. The sensor maker builds the element. A Bosch 20 to 250 kPa sensor and a Denso sensor with the same three pins are not the same curve. This page is which maker used which kind of sensor. Curves and pins for a particular part stay on that part’s page.

MakerWhat they publishWhere it turns up BoschAbsolute, ratiometric, often with an NTC. Curve 1 or curve 2, and a pin order that changes with the housing.European petrol and diesel, and many GM, Ford and Asian installations supplied by Bosch Bosch MotorsportThe same element, with a printed sensitivity and offset in V/bar.Air-box and charge-pressure parts sold for calibration and logging DensoPiezoresistive MAP and T-MAP. The aftermarket catalogue does not print a voltage curve.Toyota, Lexus, Honda, Mazda, Subaru, Suzuki, and other engines Denso supplied Siemens VDO, later ContinentalMAP and T-MAP. One catalogue range for the turbo sensor is 500 to 3000 hPa. No voltage curve is printed against the part numbers below.Volkswagen Group, Renault, Ford, Audi FordEEC-IV MAP and BARO sensors output a frequency. Later Ford engines also use analogue sensors from outside suppliers.EEC-IV speed-density, and a separate barometric sensor on some vane-air engines NXP, earlier Freescale and MotorolaThe MPX silicon element, with a published transfer function. This is a component, not a vehicle part.Inside sensors, inside some control units, and used loose on aftermarket controllers Delphi, earlier DelcoThe GM 1-bar, 2-bar and 3-bar parts. The part number selects the range.GM speed-density and the factory boosted engines

Bosch

Bosch is the maker whose ranges are printed as a catalogue. Thick-film sensors, micromechanical sensors with and without a temperature element, a moulded-cable boost sensor, and the bare cells used inside a device are on Bosch absolute-pressure sensors. Part numbers in the 0 261 230, 0 281 002 and 0 273 300 ranges are those parts. A neighbouring number is a different range, and on several of them the pin order changes too.

The motorsport air sensors are a separate list. PS-AA, PS-AL, PS-AS, PSP and the PST combined sensors each have a sensitivity and an offset, and they do not share one plug. Those figures are on Bosch Motorsport air-pressure sensors. A PST-F in that same catalogue is a fluid sensor, up to hundreds of bar. It is not an air-box sensor.

Denso

Denso’s engine-management catalogue describes the MAP sensor as a semiconductor vacuum sensor using the change in resistance of a silicon crystal under pressure. The signal is a voltage into the control unit. The same text allows the part to be used as a boost sensor upstream of the throttle, or as a turbo-manifold pressure sensor, and a T-MAP adds air temperature in the same housing.

The construction in that catalogue is a sensor chip and a circuit chip, wire-bonded, covered by gel and rubber, in a resin case with the pressure port moulded in. Denso’s stated reason for the two-layer cover is the mixture of fuel, oil and moisture in the manifold. The catalogue’s own failure notes follow from that: liquid or sustained humidity in the port, a leaking manifold or vacuum hose, and an open or short in the wiring. The fault codes it names for this sensor are P0105 to P0109.

That catalogue does not print a volts-against-pressure table. Service parts are numbered DAP, and the installation torque depends on which DAP number is in the box.

Denso service partTorque DAP0101, DAP0102, DAP0108, DAP0109, DAP0110, DAP01114.0 to 6.0 Nm DAP0105, DAP0106, DAP01072.8 to 4.1 Nm DAP0103, DAP01041.6 to 2.4 Nm

The application tables in the same catalogue use a hyphenated form, DAP-0110 and so on. Match the number on the part. A torque from the wrong row, and a curve from a different maker, are both the wrong data for that sensor.

Siemens VDO

Siemens VDO’s engine-management sensor catalogue separates a MAP, which measures manifold pressure after the throttle, from a MAP used on a turbocharged engine to measure pressure after the turbocharger. The range it prints for that turbo sensor is 500 to 3000 hPa, which is 50 to 300 kPa. A T-MAP in the same description adds a temperature element.

The part numbers in that catalogue are identification and a pin count, not a curve. No volts-per-kilopascal figure is printed against them.

PartPinsCatalogue applications 5WK96812Z3Ford Fiesta, Focus II, Ka, StreetKa 5WK9681Z3Audi A6 (4B), Ford Fusion, and a long Renault list from Clio II through Trafic II 5WK9693Z4Audi A2 and A4 (B6), and the Seat, Škoda and Volkswagen cars of that generation in the same list

A four-pin plug is consistent with a pressure element plus a temperature element, and the catalogue does describe a T-MAP. The line for 5WK9693Z itself only says pressure sensor. Treat the fourth pin as temperature only when the drawing for that part says so.

Ford, GM and the silicon element

Ford’s EEC-IV speed-density system uses a piezoelectric disc that changes frequency, not voltage. Frequency rises as manifold vacuum falls. At atmospheric pressure, on the 30.0 in-Hg barometer the pinpoint test is written against, the output is 159 Hz. The vacuum table, the key-on barometer table and the test-pin colours are on Ford MAP and BARO frequency sensors. A later Ford analogue sensor is a different part. The Siemens 5WK96812Z above is one of those, and it is not read in hertz.

GM’s speed-density and factory-boosted engines use Delphi sensors in 1-bar, 2-bar and 3-bar ranges. The part number is the range. A linear value and an offset taken from a tuning package belong to one part number and to the way that control unit scales its analogue input. They are not a family constant, and they are not published here without the Delphi sheet for that part.

Under many of these housings, and on aftermarket controllers used without a vehicle housing, the element is an NXP MPX device. MPX4115, MPX4250 and MPXH6400 each have a transfer function in the device datasheet. Those functions are on NXP MPX absolute pressure sensors. A sensor whose label is Bosch, Denso or Delphi is not measured with an MPX equation unless that sensor was built on that die and the housing calibration is the die calibration.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Manifold pressure sensor manufacturers

The same job, several makers

The car maker specifies the range, the plug and the place in the intake. The sensor maker builds the element. A Bosch 20 to 250 kPa sensor and a Denso sensor with the same three pins are not the same curve. This page is which maker used which kind of sensor. Curves and pins for a particular part stay on that part’s page.

MakerWhat they publishWhere it turns up
BoschAbsolute, ratiometric, often with an NTC. Curve 1 or curve 2, and a pin order that changes with the housing.European petrol and diesel, and many GM, Ford and Asian installations supplied by Bosch
Bosch MotorsportThe same element, with a printed sensitivity and offset in V/bar.Air-box and charge-pressure parts sold for calibration and logging
DensoPiezoresistive MAP and T-MAP. The aftermarket catalogue does not print a voltage curve.Toyota, Lexus, Honda, Mazda, Subaru, Suzuki, and other engines Denso supplied
Siemens VDO, later ContinentalMAP and T-MAP. One catalogue range for the turbo sensor is 500 to 3000 hPa. No voltage curve is printed against the part numbers below.Volkswagen Group, Renault, Ford, Audi
FordEEC-IV MAP and BARO sensors output a frequency. Later Ford engines also use analogue sensors from outside suppliers.EEC-IV speed-density, and a separate barometric sensor on some vane-air engines
NXP, earlier Freescale and MotorolaThe MPX silicon element, with a published transfer function. This is a component, not a vehicle part.Inside sensors, inside some control units, and used loose on aftermarket controllers
Delphi, earlier DelcoThe GM 1-bar, 2-bar and 3-bar parts. The part number selects the range.GM speed-density and the factory boosted engines

Bosch

Bosch is the maker whose ranges are printed as a catalogue. Thick-film sensors, micromechanical sensors with and without a temperature element, a moulded-cable boost sensor, and the bare cells used inside a device are on Bosch absolute-pressure sensors. Part numbers in the 0 261 230, 0 281 002 and 0 273 300 ranges are those parts. A neighbouring number is a different range, and on several of them the pin order changes too.

The motorsport air sensors are a separate list. PS-AA, PS-AL, PS-AS, PSP and the PST combined sensors each have a sensitivity and an offset, and they do not share one plug. Those figures are on Bosch Motorsport air-pressure sensors. A PST-F in that same catalogue is a fluid sensor, up to hundreds of bar. It is not an air-box sensor.

Denso

Denso’s engine-management catalogue describes the MAP sensor as a semiconductor vacuum sensor using the change in resistance of a silicon crystal under pressure. The signal is a voltage into the control unit. The same text allows the part to be used as a boost sensor upstream of the throttle, or as a turbo-manifold pressure sensor, and a T-MAP adds air temperature in the same housing.

The construction in that catalogue is a sensor chip and a circuit chip, wire-bonded, covered by gel and rubber, in a resin case with the pressure port moulded in. Denso’s stated reason for the two-layer cover is the mixture of fuel, oil and moisture in the manifold. The catalogue’s own failure notes follow from that: liquid or sustained humidity in the port, a leaking manifold or vacuum hose, and an open or short in the wiring. The fault codes it names for this sensor are P0105 to P0109.

That catalogue does not print a volts-against-pressure table. Service parts are numbered DAP, and the installation torque depends on which DAP number is in the box.

Denso service partTorque
DAP0101, DAP0102, DAP0108, DAP0109, DAP0110, DAP01114.0 to 6.0 Nm
DAP0105, DAP0106, DAP01072.8 to 4.1 Nm
DAP0103, DAP01041.6 to 2.4 Nm

The application tables in the same catalogue use a hyphenated form, DAP-0110 and so on. Match the number on the part. A torque from the wrong row, and a curve from a different maker, are both the wrong data for that sensor.

Siemens VDO

Siemens VDO’s engine-management sensor catalogue separates a MAP, which measures manifold pressure after the throttle, from a MAP used on a turbocharged engine to measure pressure after the turbocharger. The range it prints for that turbo sensor is 500 to 3000 hPa, which is 50 to 300 kPa. A T-MAP in the same description adds a temperature element.

The part numbers in that catalogue are identification and a pin count, not a curve. No volts-per-kilopascal figure is printed against them.

PartPinsCatalogue applications
5WK96812Z3Ford Fiesta, Focus II, Ka, StreetKa
5WK9681Z3Audi A6 (4B), Ford Fusion, and a long Renault list from Clio II through Trafic II
5WK9693Z4Audi A2 and A4 (B6), and the Seat, Škoda and Volkswagen cars of that generation in the same list

A four-pin plug is consistent with a pressure element plus a temperature element, and the catalogue does describe a T-MAP. The line for 5WK9693Z itself only says pressure sensor. Treat the fourth pin as temperature only when the drawing for that part says so.

Ford, GM and the silicon element

Ford’s EEC-IV speed-density system uses a piezoelectric disc that changes frequency, not voltage. Frequency rises as manifold vacuum falls. At atmospheric pressure, on the 30.0 in-Hg barometer the pinpoint test is written against, the output is 159 Hz. The vacuum table, the key-on barometer table and the test-pin colours are on Ford MAP and BARO frequency sensors. A later Ford analogue sensor is a different part. The Siemens 5WK96812Z above is one of those, and it is not read in hertz.

GM’s speed-density and factory-boosted engines use Delphi sensors in 1-bar, 2-bar and 3-bar ranges. The part number is the range. A linear value and an offset taken from a tuning package belong to one part number and to the way that control unit scales its analogue input. They are not a family constant, and they are not published here without the Delphi sheet for that part.

Under many of these housings, and on aftermarket controllers used without a vehicle housing, the element is an NXP MPX device. MPX4115, MPX4250 and MPXH6400 each have a transfer function in the device datasheet. Those functions are on NXP MPX absolute pressure sensors. A sensor whose label is Bosch, Denso or Delphi is not measured with an MPX equation unless that sensor was built on that die and the housing calibration is the die calibration.

Revision 1: Manifold pressure sensor manufacturers

The same job, several makers

The car maker specifies the range, the plug and the place in the intake. The sensor maker builds the element. A Bosch 20 to 250 kPa sensor and a Denso sensor with the same three pins are not the same curve. This page is which maker used which kind of sensor. Curves and pins for a particular part stay on that part’s page.

MakerWhat they publishWhere it turns up
BoschAbsolute, ratiometric, often with an NTC. Curve 1 or curve 2, and a pin order that changes with the housing.European petrol and diesel, and many GM, Ford and Asian installations supplied by Bosch
Bosch MotorsportThe same element, with a printed sensitivity and offset in V/bar.Air-box and charge-pressure parts sold for calibration and logging
DensoPiezoresistive MAP and T-MAP. The aftermarket catalogue does not print a voltage curve.Toyota, Lexus, Honda, Mazda, Subaru, Suzuki, and other engines Denso supplied
Siemens VDO, later ContinentalMAP and T-MAP. One catalogue range for the turbo sensor is 500 to 3000 hPa. No voltage curve is printed against the part numbers below.Volkswagen Group, Renault, Ford, Audi
FordEEC-IV MAP and BARO sensors output a frequency. Later Ford engines also use analogue sensors from outside suppliers.EEC-IV speed-density, and a separate barometric sensor on some vane-air engines
NXP, earlier Freescale and MotorolaThe MPX silicon element, with a published transfer function. This is a component, not a vehicle part.Inside sensors, inside some control units, and used loose on aftermarket controllers
Delphi, earlier DelcoThe GM 1-bar, 2-bar and 3-bar parts. The part number selects the range.GM speed-density and the factory boosted engines

Bosch

Bosch is the maker whose ranges are printed as a catalogue. Thick-film sensors, micromechanical sensors with and without a temperature element, a moulded-cable boost sensor, and the bare cells used inside a device are on Bosch absolute-pressure sensors. Part numbers in the 0 261 230, 0 281 002 and 0 273 300 ranges are those parts. A neighbouring number is a different range, and on several of them the pin order changes too.

The motorsport air sensors are a separate list. PS-AA, PS-AL, PS-AS, PSP and the PST combined sensors each have a sensitivity and an offset, and they do not share one plug. Those figures are on Bosch Motorsport air-pressure sensors. A PST-F in that same catalogue is a fluid sensor, up to hundreds of bar. It is not an air-box sensor.

Denso

Denso’s engine-management catalogue describes the MAP sensor as a semiconductor vacuum sensor using the change in resistance of a silicon crystal under pressure. The signal is a voltage into the control unit. The same text allows the part to be used as a boost sensor upstream of the throttle, or as a turbo-manifold pressure sensor, and a T-MAP adds air temperature in the same housing.

The construction in that catalogue is a sensor chip and a circuit chip, wire-bonded, covered by gel and rubber, in a resin case with the pressure port moulded in. Denso’s stated reason for the two-layer cover is the mixture of fuel, oil and moisture in the manifold. The catalogue’s own failure notes follow from that: liquid or sustained humidity in the port, a leaking manifold or vacuum hose, and an open or short in the wiring. The fault codes it names for this sensor are P0105 to P0109.

That catalogue does not print a volts-against-pressure table. Service parts are numbered DAP, and the installation torque depends on which DAP number is in the box.

Denso service partTorque
DAP0101, DAP0102, DAP0108, DAP0109, DAP0110, DAP01114.0 to 6.0 Nm
DAP0105, DAP0106, DAP01072.8 to 4.1 Nm
DAP0103, DAP01041.6 to 2.4 Nm

The application tables in the same catalogue use a hyphenated form, DAP-0110 and so on. Match the number on the part. A torque from the wrong row, and a curve from a different maker, are both the wrong data for that sensor.

Siemens VDO

Siemens VDO’s engine-management sensor catalogue separates a MAP, which measures manifold pressure after the throttle, from a MAP used on a turbocharged engine to measure pressure after the turbocharger. The range it prints for that turbo sensor is 500 to 3000 hPa, which is 50 to 300 kPa. A T-MAP in the same description adds a temperature element.

The part numbers in that catalogue are identification and a pin count, not a curve. No volts-per-kilopascal figure is printed against them.

PartPinsCatalogue applications
5WK96812Z3Ford Fiesta, Focus II, Ka, StreetKa
5WK9681Z3Audi A6 (4B), Ford Fusion, and a long Renault list from Clio II through Trafic II
5WK9693Z4Audi A2 and A4 (B6), and the Seat, Škoda and Volkswagen cars of that generation in the same list

A four-pin plug is consistent with a pressure element plus a temperature element, and the catalogue does describe a T-MAP. The line for 5WK9693Z itself only says pressure sensor. Treat the fourth pin as temperature only when the drawing for that part says so.

Ford, GM and the silicon element

Ford’s EEC-IV speed-density system uses a piezoelectric disc that changes frequency, not voltage. Frequency rises as manifold vacuum falls. At atmospheric pressure, on the 30.0 in-Hg barometer the pinpoint test is written against, the output is 159 Hz. The vacuum table, the key-on barometer table and the test-pin colours are on Ford MAP and BARO frequency sensors. A later Ford analogue sensor is a different part. The Siemens 5WK96812Z above is one of those, and it is not read in hertz.

GM’s speed-density and factory-boosted engines use Delphi sensors in 1-bar, 2-bar and 3-bar ranges. The part number is the range. A linear value and an offset taken from a tuning package belong to one part number and to the way that control unit scales its analogue input. They are not a family constant, and they are not published here without the Delphi sheet for that part.

Under many of these housings, and on aftermarket controllers used without a vehicle housing, the element is an NXP MPX device. MPX4115, MPX4250 and MPXH6400 each have a transfer function in the device datasheet. Those functions are on NXP MPX absolute pressure sensors. A sensor whose label is Bosch, Denso or Delphi is not measured with an MPX equation unless that sensor was built on that die and the housing calibration is the die calibration.