Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Turbocharging
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Acura, Honda

Changes from revision 1 to revision 2

Removed text is struck through; added text is highlighted.

Turbocharging the naturally aspirated Honda D-series, B-series, K-series (K20 and K24), H22 and F20C/F22C engines is one of the most widely documented forced-induction conversions. Builds fall into three broad groups: low-boost conversions on stock internals using a small T25/T28-, GT28-, G25- or T3/T04E-class turbo; moderate-boost K- and B-series builds of roughly 400–550 whp using GT30/GTX30-, G25-660/G30-, Precision 5558–6266- or EFR-class turbos; and fully built, sleeved drag and time-attack engines running 25–45 psi on E85 or race fuel. Honda publishes no "safe power on stock internals" figure for any of these engines. Every such figure on this page is a tuner estimate, vendor claim or owner report and is marked as such. Power figures are wheel horsepower (whp) unless stated.

Engines and how they tolerate boost

The common failure on a boosted stock Honda bottom end is detonation damage to the cast pistons (cracked ring lands), not a broken block. Compression ratio, fuel quality, intake temperature and knock control decide how much boost a given engine survives far more than any single psi figure. The table below summarises the most widely repeated stock-internal estimates; none comes from Honda.

EngineBore × stroke (mm)CompressionMost repeated stock-internal estimateUsual first failure D16Y7/Y8/Z675 × 909.1–9.6:1About 200–220 whp (owner consensus)Rods and rod bolts, cast pistons B16A/B18C81 × 77.4 / 87.210.0–11.1:1About 300–350 whp (owner reports)Ring lands under detonation B18B (LS)81 × 899.2:1Mild boost only on stock pistons and sleeves (owner advice of about 10 psi)Ring lands; rods at higher rpm K20A2/K20Z1/K20Z386 × 8611.0:1About 400 whp (HP Academy estimate)Ring lands; high compression limits boost K24A1/A4/A8/Z187 × 999.6–9.7:1About 450 whp (HP Academy estimate)Ring lands; rods at high rpm K24A287 × 9910.5:1About 450 whp (HP Academy estimate)Ring lands H22A87 × 90.710.0–11.0:1About 300–350 whp (owner estimates)Ring lands; FRM bores limit piston choice F20C87 × 8411.0–11.7:1About 400–440 whp at 15–18 psi reported on stock blocksHigh compression requires a careful tune

K20 and K24

Both share an open-deck aluminium block with cast-in iron liners and a bedplate, a DOHC 16-valve head with intake cam phasing (VTC) and i-VTEC. Two head families matter for boost. "Performance" heads switch VTEC on both camshafts: K20A, K20A2, K20Z1, K20Z3, K20Z4, K24A2 and the TSX K24Z3. "Economy" heads switch VTEC on the intake cam only: K20A3, K24A1, K24A4, K24A8, K24Z1 and the direct-injection K24W. The K24A2 is therefore a dual-VTEC engine, contrary to a common assumption.

The most-cited estimates, from HP Academy, are about 400 whp for a K20 and about 450 whp for a K24 on stock internals with a good tune, adequate fuel and effective knock control. Aftermarket rods and pistons raise that to about 600–700 whp, beyond which the open deck becomes the limit and sleeves or block guards are used. Owner claims of 500–600 whp on stock engines exist but are single cases. One conservative source puts the safe figure as low as about 300 whp. Low-compression K24 blocks (A1/A4/A8/Z1, 9.6–9.7:1) are preferred over the 11:1 performance engines for stock-bottom-end turbo builds because of their larger detonation margin. The K20A2 has piston oil squirters and a factory oil cooler; the economy blocks lack squirters.

Rod vendors describe the naturally aspirated K-series rods as powder metal, but no Honda statement confirming the rod material for each engine code has been found. By contrast, Honda's own description of the factory-turbo K20C1 (FK8/FL5 Civic Type R) specifies 9.8:1 compression, a forged crankshaft, forged one-piece rods, piston oil jets, sodium-filled exhaust valves and about 23 psi peak boost, which shows what Honda considered necessary for sustained boost on this architecture.

K20 head on K24 block (the "K24 mod" or "frankenstein")

The K20/K24 hybrid fits a K20 performance head (K20A, K20A2, K20Z1 or K20Z3) to a K24 block, combining the K24's 2.4 litres and 99 mm stroke with the better-flowing K20 head. Retailer piston listings give both heads a combustion chamber of about 50.5 cc, so the hybrid keeps the K24 piston's compression: about 9.6:1 with A1 pistons, 9.7:1 with A4/A8/Z1 pistons and 10.5:1 with A2 pistons. A stock K24A1, A4 or A8 bottom end with a K20 head is therefore a ready-made low-compression turbo base, although the hybrid is also widely built naturally aspirated.

Block: K24A-series blocks are the documented base. Hybrid Racing's build guide states that Z-series blocks are not supported, and other guides agree; forum builds on Z blocks exist but no reliable procedure has been published. Taller-deck parts: K24 head gasket (87 mm bore), K24 timing chain, K24 front cover and dipstick. The K24 deck is 231.5 mm against 212 mm for the K20. Oiling: the K20A2 water-pump housing carries an oil-cooler port, which must be retained with the housing, deleted or plumbed to an external cooler. Builds that fit a K20A/A2 or F20C oil pump to delete the K24 balance shafts must trim the pump body and remove and plug the K24 balance-shaft oil jet (restrictor orifice, given in a forum thread as 11135-PNA-000). Cam phasing: the K24 VTC gear can be retained, or the 50° gear from the JDM K20A Type R can replace the 25° gear for more midrange. Piston-to-valve clearance: K24A4 and K24A8 pistons contact K20 head valves; A1/A2 or aftermarket pistons are used instead. Aggressive cams or the 50° VTC gear reduce clearance further, so a clay check is advised. Management: an aftermarket ECU, typically Hondata K-Pro, to run the K20 cams, VTEC point and VTC map on the larger displacement.

The K24's longer stroke gives a lower rod-to-stroke ratio (about 1.54 against 1.62 for the K20), raising piston speed and side-loading. This is one reason boosted K24 builds limit rpm or fit forged rods. No hybrid-specific power limit has been published; the K24 estimates above apply. A separate race-engine configuration runs an OEM K24 crankshaft in a K20 block with custom rods or pistons.

B-series and LS/VTEC

The LS/VTEC hybrid fits a DOHC VTEC head (B16A, B17A or B18C) to the non-VTEC B18A/B18B "LS" block, or to a B20 block ("B20VTEC"). The LS block is cheap, has the longest B18 stroke (89 mm, 1,834 cc) and a low stock compression of about 9.5:1 with a VTEC head, which suits boost. The conversion needs an external VTEC oil feed from a sandwich plate or sender tee to the head (the head's deck passage is plugged), LS/VTEC alignment dowels, GSR/ITR-length head studs, and a GSR/ITR or LS timing belt with the matching water pump: the B16 belt does not fit the taller block. Head-gasket choice is disputed; one detailed guide insists on the OEM LS gasket because a VTEC gasket can leak at the gallery hole the LS block lacks.

Owner reports put cast ring-land failure at around 300–350 whp and the factory liners as unreliable above about 400–500 whp even with forged pistons and rods. Beyond that, Darton MID or Golden Eagle sleeves are standard. A documented B18C1 at about 1,200 hp used Golden Eagle sleeves, Wiseco pistons and CP-Carrillo rods.

D-series

The D16 is the cheapest platform: common, low in compression (9.1–9.6:1) and simple. The usual hybrid, the "mini-me", fits a SOHC VTEC head (D16Z6 or D16Y8) to a non-VTEC D16Y7 block and stays close to the Y7's 9.4:1; the thicker Z6 head gasket is suggested for turbo use. Owner consensus puts the stock rods and rod bolts at about 200–220 whp, and the D16Y8 bottom end is described as prone to spinning rod bearings under boost. Above that, rods and pistons are replaced, and sleeving is needed for high boost.

Engine management

B, D and H-series: OBD1 Honda ECUs

Turbo B, D and H builds almost always run a 1992–95 OBD1 Keihin ECU, even in 1996–2001 cars, which use an OBD2a (1996–98) or OBD2b (1999–2001) to OBD1 jumper harness because the OBD1 tuning tools are far more mature. The P28 (1992–95 Civic Si/EX; VTEC, no knock control) is the standard tuning base. The P30 adds knock control, and the P72 (1994–95 Integra GS-R) adds knock and intake air bypass control, so it is chosen where those are wanted. Hondata's s300 supports the P06, P28, P30, P61, P72, P74, P75 and PR4 (manual transmission only), with the s300j for JDM ECUs; the H22 Prelude P13/P14 ECUs are not supported, so H-series builds use a P28/P72-type ECU through a conversion harness. Other routes are a socketed ECU with Neptune RTP and a Moates Demon2, eCtune, Crome or Uberdata. Moates describes Neptune as actively developed and Crome and eCtune as less well maintained.

US OBD1 ECUs carry the circuit footprint but not the components for a PWM boost-control output. Hondata's s300 instructions wire the boost solenoid to pin A11 on US ECUs (A17 on JDM ECUs), using a three-port solenoid drawing no more than 3 A, with no relay between ECU and solenoid, and an ECU boost cut in case of solenoid or hose failure.

K-series ECUs

Hondata K-Pro (v4): installed in 2002–04 ECUs (RSX Type-S PRB A01–A12 and 305, PND, EP3 Civic Si PNF, PRA, PRC, PRD, PPA, PPL). Hondata documents fuel and ignition tables to 60 psi and 11,000 rpm, support for MAP sensors to 5 bar and above, a PWM boost-control output, gear-based corrections, an ethanol input and launch control with anti-lag. Manual transmission only. 2005–06 RSX ECUs (PRB-A13 to A16) have a different processor and cannot take a K-Pro; Hondata supplies a modified 2002–04 ECU and adapter harness instead. KTuner's in-ECU board is built on exactly these 2005–06 ECUs and does not support the 2002–04 units. Drive-by-wire cars (2006–11 Civic Si, TSX, 2006–09 S2000 and later K24 cars) cannot run a K-Pro. They are reflashed with Hondata FlashPro or KTuner Flash V2. On the 2006–11 Civic Si, FlashPro offers AFM, MAP or hybrid load tables, boost control, anti-lag and an ethanol input; Hondata lists 4 bar MAP support (about 43 psi) for the TSX. Engine swaps of drive-by-wire engines onto K-Pro convert to a cable throttle and K20A2-style harness. Immobiliser: US K-series ECUs will not power the fuel pump or coils in a swap without a bypass box, the K-Pro software disable, or a JDM PRC ECU.

MAP sensor, injectors and IAT

Hondata gives the stock Honda MAP sensor's limit as about 10.5 psi of boost, so the boost cut must sit below that on a stock sensor. Common replacements are the Skunk2 and Omni 2.5 bar sensors, 3–4 bar units from Omni, SpeedFactory, Skunk2 and K-Tuned, the remote-mounted AEM 3.5 bar, and Hondata 4 bar and 7 bar sensors; each needs matching scalar and offset settings in the ECU. No Honda OEM 2.5 bar sensor has been identified. On the K-series, the Acura RDX injector (410 cc/min at 38 psi, a plug-in high-impedance part) is the usual first upgrade; 1,000–1,050 cc injectors cover the 400–600 bhp class. Honda OBD1 and OBD2 ECUs drive high-impedance injectors, so older low-impedance injectors need a resistor box. Hondata advises relocating the IAT sensor to read air after the turbo, usually in the charge pipe before the throttle body.

Standalone ECUs

Builders move to a standalone ECU for drive-by-wire on unsupported platforms, high injector or output counts, CAN dash and power-distribution integration, multi-axis closed-loop boost and race features. Plug-in options include the Haltech Nexus plug-in HT-231001 for EP3/DC5 (onboard 4 bar MAP), the Haltech Nexus Rebel K (kit HT-220206: ECU HT-220003 with the HT-186402 terminated main harness for K20A, K24A and K24Z engines, sold for manual-transmission applications, with injector, throttle and transmission sub-harnesses separate), the Haltech Elite with plug-in adaptors (the Elite 2500 is required to retain drive-by-wire on the AP2 S2000), the Link G4X CIVICLink K20X (HC20X) and HC92X for OBD1 B-series, the AEM Series 2 and Infinity, and MoTeC M1 with custom harnesses. Many 400–500 whp K24 turbo builds still run a K-Pro.Builders move to a standalone ECU for drive-by-wire on unsupported platforms, high injector or output counts, CAN dash and power-distribution integration, multi-axis closed-loop boost and race features. Plug-in options include the Haltech Nexus plug-in HT-231001 for EP3/DC5 (onboard 4 bar MAP), the Haltech Elite with plug-in adaptors (the Elite 2500 is required to retain drive-by-wire on the AP2 S2000), the Link G4X CIVICLink K20X (HC20X) and HC92X for OBD1 B-series, the AEM Series 2 and Infinity, and MoTeC M1 with custom harnesses. Many 400–500 whp K24 turbo builds still run a K-Pro.

Exhaust manifolds

LayoutDescription and use Cast log / stock locationShort cast-iron manifold placing the turbo where the factory header sits. Used in budget kits and the old GReddy and HKS kits. Compact and quick to warm but restrictive at high power. Ramhorn (cast or tubular)Runners curve to a central turbine flange low at the front of the head. Common on B/D-series and the 2006–11 Civic Si. Top mountRunners rise to a flange above the head; allows larger turbos and 4" downpipes but needs bonnet, firewall and sometimes steering clearance. SidewinderK-series layout that turns the runners toward the gearbox end and places the turbo over the transmission. The usual layout for K20/K24 builds in EP3, DC5, RSX and K-swapped chassis. Rear mountNo current bolt-on Honda rear-mount kit has been identified.

Turbine flanges range from T25/T28 for small Garrett frames, through T3 for most budget and mid-range kits, to T4 open or divided and V-band for larger turbos; several top-mount manifolds are drilled for both T3 and T4. Fabricated manifolds carry external wastegates, typically 38 mm on budget kits, 44–46 mm V-band on most branded manifolds and 60 mm or twin gates on large sidewinders and top mounts. Established fabricated-manifold makers include SpeedFactory Racing (1.5" schedule 40 stainless with 1/2" flanges, vendor listing), PLM, Full-Race, Blox (schedule 40 T304) and, in the UK, Tegiwa (its own 304 sidewinder for a T3 turbo and 45 mm V-band gate) and Tuning Developments (T3 sidewinder with 44 mm gate, sold by Pro-Race Engineering at £750 inc VAT, seen 19 November 2026). Sources conflict on whether the Tegiwa manifold uses schedule 10 or schedule 40 tube.

Most fabricated Honda manifolds are 304 stainless. No mainstream Honda manifold is advertised in 321, and no controlled comparison of cracking between the grades, or between cast SiMo and Ni-resist irons, exists for these applications. Schedule 40 tube is heavier and slower to heat but generally regarded as more crack-resistant than schedule 10.

Cracking: owner reports describe GReddy RSX and S2000 kit manifolds as prone to cracking, and an early Inline Pro S2000 sidewinder cracked in the base metal. Owners attribute such failures to a missing manifold-to-block brace, no flex section in the downpipe, an unsupported dump tube and thin early wastegate flanges. Reports exist for budget and premium manifolds alike; there is no evidence that budget manifolds crack measurably more often. Wastegate creep: a 90° wastegate entry on K-series sidewinders, combined with the engine's high volumetric efficiency and a free-flowing turbine, is linked to boost overshooting the spring pressure; one documented case overshot a 10 psi spring to a 24 psi boost cut. Fixes are a teardrop entry at about 45°, a larger or second gate, or a "wastegate-priority" sidewinder. Warranty: SpeedFactory's warranty covers welding defects only and excludes manifolds that have been heat-wrapped or fitted with an improper downpipe or dump tube.

Turbo kits

No premium kit examined includes fuel-system parts or engine management; these are always bought separately. Prices below are as listed on 19 November 2026 unless stated.

KitApplicationTurbo and manifoldNotes Full-Race FG2/FA5 Civic Si2006–11 Civic Si K20Z3T3/T04E 57-trim, GT2871R, GT3076R, GT3582R or HTA3586R on a T3 tubular manifold, TiAL 44 mm gateManufacturer claims about 350 whp (57-trim) to 430–440 whp (GT3582R) on a stock K20Z3 at 11–12 psi on 91–93 octane. Not listed in Full-Race's store when checked; availability not established. Full-Race FK8 (sold by 4 Piston)K20C1 Civic Type RUpgrade turbo on V-band; OEM electronic wastegate retainedUS$2,782.99, sold out. GReddy T517Z2002–03 RSX Type-ST517Z internal-gate turbo on a cast-iron manifold, preset about 8.5 psiIncluded 440 cc injectors and an e-Manage piggyback. Reported discontinued. HKS2002–04 RSX Type-SGT2835 ball-bearing, internal gate, cast manifoldReported discontinued. PTuning S2000S2000GT3076R standard (GT3582R/GTX options), T304 V-band manifoldUS$7,430 base; no fuel or tune. Inline Pro Stage 2 RaceS2000Precision journal-bearing turbo, T4 front mountUS$5,999; oil-filter relocation extra. Rev9 TCK-001 / 002 / 003RSX and EP3 / B-series / D-seriesTX-50E-57 T3 turbo on cast manifolds, 38 mm 7 psi gateAbout US$770–1,400. Owner reviews cite missing or poor hardware rather than manifold failure. CXRacingDC5/RSX, B- and D-seriesGT35-type turbo on sidewinder or ramhorn; cast D-series kitK20 kit about US$1,299 without intercooler (search listing only).

Budget kits (Rev9, CXRacing, JDM Performance, Bull Boost and unbranded online kits) cost roughly a third to a half of a premium kit. Owner reviews consistently report short studs, torn gaskets, generic bolts, missing parts and piping that needs modification. Several brands often associated with Honda turbo builds do not make Honda turbo kits: Kraftwerks sells Rotrex supercharger kits; Hondata makes engine management only; 4 Piston Racing retails the Full-Race FK8 kit; and Hybrid Racing retails SpeedFactory manifolds. No turbo manifold or kit from K-Tuned, ISR Performance or DC Sports has been found, although K-Tuned sells a timing-chain tensioner cover with a -10AN turbo oil return. No complete UK-manufactured K-series kit has been identified; UK builds normally combine a UK-sold or imported manifold with a separately bought turbo.

Supporting parts

Oil feed and drain: the feed is usually tapped from the oil-pressure-switch port or filter-housing area. The drain must fall continuously by gravity into the sump above the oil level, through a welded or bolt-on -10AN sump bung or, on K20A/K20Z/K24A engines, a timing-chain tensioner cover with a -10AN return (not K24Z). Poor drainage produces smoke through the turbo seals. Fuel pump: a Walbro 255 l/h in-tank pump is the usual first step; owner reports put its practical limit at about 450 whp, against vendor claims of about 600 hp. An AEM 340 or 400 l/h pump is used beyond that. The EP3/RSX-generation K20 fuel system is returnless, which one UK supplier describes as a restriction around 400 bhp. Intercooler and exhaust: 2.5"-thick cores suit about 500 bhp; 3" V-band downpipes with a flex section are standard. Clutch: six-puck ceramic single-plate clutches are recommended for higher-power K-series builds and twin-plate clutches from about 500 whp.

Common turbochargers

Garrett states that its horsepower ratings are flywheel-equivalent figures calculated from compressor choke flow, so they describe compressor capacity, not likely wheel power. Precision and BorgWarner ratings are similar maximum-capability claims.

TurboCompressor inducer/exducer (mm)Published ratingTypical Honda use Garrett GT2560R / GT2860RS46/60, 47/60170–270 hp / 250–360 hpD16 and B16 low boost T3/T04E 50–57 trim53.9–56.6 inducerKit-maker figures of about 420–460 whpClassic D/B-series kit turbo at 8–15 psi Garrett G25-550 / G25-66048/60, 54/67300–550 hp / 350–660 hpB-series and stock-internal K24 street builds Garrett GT3076R57/76310–525 hpLong-time default for B18/B20, K20/K24 and F20C at 300–450 whp Garrett GTX3076R Gen II / G30-77058/76, 58/71400–750 hp / 475–770 hpK20/K24 at 400–550 whp; built K-series Precision Gen2 5558 / 6062 / 626655, 60, 62 inducer650 / 750 / 800 hpB/K-series 400–650 whp; built engines BorgWarner EFR 6758 / 716354/67, 57/71500 / 550 hp peakK-series street (Full-Race kits) Garrett GTX3582R Gen II, G35, Precision 6870 and larger66/82 and up450–900 hp and upBuilt and drag K/B-series

Budget alternatives include unbranded T3/T4 hybrids, second-hand Holset HX35 diesel turbos on B-series and Pulsar G-series replicas; their specifications rest on seller claims or forum measurements. Smaller turbine housings (about 0.6 A/R) favour response and larger ones (0.8–1.0 A/R) favour top-end power.

Reported power results

For comparison, Acura rated the B18C1 at 170 hp; the K20A2 is quoted at 200 hp and the K24A2 at 200–205 hp (the later figure under a revised SAE method), and the D16Y8 at about 127 hp.

EngineInternalsTurboBoost and fuelResultEvidence D16 (various)StockSmall T3 / kit turbos6–8 psiAbout 150–210 whpOwner reports D16Z6Built, Darton sleevesPrecision 626228 psi, E85717 whp, Mustang dynoMagazine spec sheet B18CStockPrecision 5457, T3/T04E 57-trim8–12 psiAbout 300–370 whp; 410 whp on race fuelOwner reports; one B16B piston failure at 10 psi B18C1Built, Golden Eagle sleevesPTE 728045 psi, race fuel983 whp, DynojetMagazine spec sheet K24Z3StockGarrett G25-66012 psi, E85470 whpBuilder report K20Z3Stock (junkyard engine)Not identified18.5 psi503, then 530 whpBlog build series; source excerpts only K24Z7Not statedGarrett GTX3076RAbout 15 psi, 93 octane400.85 whpShop report K24A2BuiltBorgWarner S300SX318 psi, 92 octane520 whp, DynapackMagazine spec sheet K20Stock sleeves, forged pistons and rodsPrecision 626528 psi, E85745 whpShop report K20ABuilt, Golden Eagle sleevesGarrett GTX3586RS40 psi, E85874 whp, DynapackMagazine spec sheet K24 (4 Piston)Built, ductile sleevesPrecision PT7285About 30–33 psi, E851,038–1,042 hp; wheel or crank not statedBuilder figure, two reports K-series drag CivicBuiltPrecision GT42R42 psi, race fuel1,125 whp, DynapackMagazine spec sheet F20CStock internals, ARP studsGarrett GT3076R15 psi, 93 octane431 whp, Dyno DynamicsMagazine H22Stock cams, 10:1Not stated16 psi439 whpOwner report F22C1Built, Golden Eagle sleevesPrecision 646645 psi, race fuel961 whp, Mainline hub dynoMagazine spec sheet

The documented stock-internal K-series results support roughly 450–530 whp as achievable but at risk; the frequently quoted "350–450 whp on a stock K" is a consistent community generalisation rather than a tested limit. Every result above about 550 whp found comes from a sleeved or forged engine on E85 or race fuel at 25–45 psi.

Comparing power figures

Forum posts often give "hp" without stating wheel or crank, and builder engine-dyno figures cannot be compared with chassis-dyno wheel figures. Mustang (loaded) dynos are reported to read about 5–15% below Dynojet inertia dynos; hub dynos such as Dynapack and Mainline produced several of the headline figures above. UK rolling roads usually report a flywheel estimate from a coast-down measurement or a fixed loss (about 15% is commonly used), so a UK flywheel figure is not directly comparable with a US wheel figure.

Not established

Rod material (forged or powder metal) for each naturally aspirated K20/K24 engine code, and any measured failure threshold for stock K, B or D internals. Whether K24Z blocks are suitable for the K20 head hybrid, and K20/K24 exhaust-flange compatibility across head codes. The stock-internal limit of the K20C1. Current availability of Full-Race's RSX, FG2/FA5 and S2000 kits, and official discontinuation of the GReddy and HKS RSX kits. UK rolling-road results for turbo Honda engines with full specifications.

Related pages

Hondata s300: Honda factory ECU tuning and logging Haltech Nexus Plug-in Honda EP3 and DC5 Haltech Nexus Rebel K and its connector pinout Link G4X HC20X plug-in ECU AEM EMS Series 2 30-6030 Wideband oxygen sensor types Acura: history and carsHondata s300: Honda factory ECU tuning and logging Haltech Nexus Plug-in Honda EP3 and DC5 Link G4X HC20X plug-in ECU AEM EMS Series 2 30-6030 Wideband oxygen sensor types Acura: history and cars

Sources

All sources accessed 19 November 2026. "Undated" means no publication date was shown. Sources marked "search excerpt" refused automated access; their content was read from search-engine results and may be stale.

Manufacturer documentation

Hondata, KPro product page, undated. Hondata, KPro 05-06 RSX, undated. Hondata, OBD1 ECU reference, undated. Hondata, SManager help: MAP sensor installation and boost control solenoid installation, undated. Hondata, KManager help: IAT sensor, undated. Hondata, FlashPro help: Civic Si 2006–2011 and TSX 2004–2014, undated. KTuner, FAQ, undated. Moates, Honda overview read me, undated. Haltech, Nexus plug-in ECU – Honda EP3 and DC5, undated (search excerpt). Haltech, HT-186402 Nexus Rebel K main terminated harness, undated (search excerpt). Mako Motorsport, Haltech Nexus Rebel K ECU and harness kit HT-220206, retailer listing (search excerpt). Link ECU, CIVICLink K20X (HC20X), undated (search excerpt). American Honda, Honda Civic Type R powertrain, 14 June 2017. Acura, 1995 Acura Integra specifications. Full-Race Motorsports, Civic Si turbo kit FAQ, undated. GReddy, Turbo kit Acura RSX Type-S T517Z installation manual, undated. PTUNING, S2000 turbo system PTP-TBK-30300, undated. Garrett Motion, GT3076R, GTX3076R Gen II, G25-550 and G-25 sell sheet (2020). Garrett Motion, Motion Auto's K24-powered AWD Civic, 13 April 2022. Precision Turbo & Engine, Gen 2 PT6266, undated. BorgWarner, EFR series product information (PDF), undated.Hondata, KPro product page, undated. Hondata, KPro 05-06 RSX, undated. Hondata, OBD1 ECU reference, undated. Hondata, SManager help: MAP sensor installation and boost control solenoid installation, undated. Hondata, KManager help: IAT sensor, undated. Hondata, FlashPro help: Civic Si 2006–2011 and TSX 2004–2014, undated. KTuner, FAQ, undated. Moates, Honda overview read me, undated. Haltech, Nexus plug-in ECU – Honda EP3 and DC5, undated (search excerpt). Link ECU, CIVICLink K20X (HC20X), undated (search excerpt). American Honda, Honda Civic Type R powertrain, 14 June 2017. Acura, 1995 Acura Integra specifications. Full-Race Motorsports, Civic Si turbo kit FAQ, undated. GReddy, Turbo kit Acura RSX Type-S T517Z installation manual, undated. PTUNING, S2000 turbo system PTP-TBK-30300, undated. Garrett Motion, GT3076R, GTX3076R Gen II, G25-550 and G-25 sell sheet (2020). Garrett Motion, Motion Auto's K24-powered AWD Civic, 13 April 2022. Precision Turbo & Engine, Gen 2 PT6266, undated. BorgWarner, EFR series product information (PDF), undated.

Technical articles and build guides

P. Kelly, Everything you need to know about the Honda K20 and the Honda K24, HP Academy, undated. A. Simon, Stock to 1200hp: Honda B18C, HP Academy, undated. D. Cordell, K20/K24 hybrid engine build guide, Hybrid Racing, 6 September 2017. Hybrid Racing, K-series ECU options, undated. A. Parsons, Honda K20 vs K24 engine guide, 8020 Automotive, 7 June 2022 (updated 12 March 2025). Exo Racing, Ultimate Honda Civic turbo B/K-series conversion guide, undated. Wikipedia, Honda K engine, Honda B engine and Honda D engine, live pages. Drifted, Ultimate RSX turbo kit guide, 1 August 2023 (affiliate buyer's guide). sbraceengineering.co.uk, Measuring engine power, undated.

Dyno results and build reports

DSPORT, 717hp D16Z6-powered Civic, 26 December 2017. DSPORT, 983WHP Civic EK, 17 November 2015. DSPORT, 520 WHP Honda Civic Si, 17 October 2018. DSPORT, 874 WHP Honda Civic Si, 30 March 2021. DSPORT, 1,125 HP K-series Civic drag racer, 8 January 2012. DSPORT, 431 horsepower turbocharged S2000, 10 February 2017. DSPORT, 961 WHP Honda S2000, 23 February 2022. Engine Swap Depot, KPower Industries turbo K24 Miata, 5 May 2021. EngineLabs, What goes into a 1,000 horsepower 2.4-litre Honda engine, 19 April 2019. National Speed, Civic Si GTX3076R turbocharger install, undated. The Truth About Cars, Neglected Integra GS-R K-swap build: dyno finale, undated (search excerpt; page returned 404). Honda-Tech, 745whp stock-sleeve K20, 6265, E85, 9 June 2014.

Vendor listings

Pro-Race Engineering, Tuning Developments sidewinder T3 turbo manifold, Honda K20, price seen 19 November 2026. Tegiwa, Tegiwa sidewinder exhaust turbo manifold 304SS Honda K-series (search excerpt). Hybrid Racing, SpeedFactory K-series sidewinder manifold (search excerpt). Hybrid Racing, Acura RDX 410cc injectors, undated. 4 Piston Racing, Full-Race turbo kit, K20C1 Civic Type R, price seen 19 November 2026. Evasive Motorsports, Inline Pro Stage 2 turbo kit (race) S2000, price seen 19 November 2026. K Series Parts, Rev9 TCK-001 and TCK-003 listings with owner reviews (2017–2025). CXRacing, K20 RSX GT35 turbo kit (search excerpt).

Owner discussions

Honda-Tech, Wastegate creep with sidewinder, 6266, K24/K20, 18–21 September 2019. S2Ki, GReddy manifold replacement options, 18 February 2010; and Inline Pro turbo manifold cracked, May 2010. G2IC forum, How to build a reliable LS/VTEC or B20VTEC, 26 November 2006. Honda-Tech, D16Y7 with D16Z6 head mini-me swap, 2010–2019. Honda-Tech, K24A1/K20A2 head oil orifice blocking, May 2007. Honda-Tech, Boosted stock B18C with 57-trim turbo, April 2015; B16B at 7 psi, May 2008; Turbo D-series dyno numbers, August 2003; GT3076R users' results, August 2006.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Honda turbo conversions: engines, ECUs, manifolds, kits and results

Turbocharging the naturally aspirated Honda D-series, B-series, K-series (K20 and K24), H22 and F20C/F22C engines is one of the most widely documented forced-induction conversions. Builds fall into three broad groups: low-boost conversions on stock internals using a small T25/T28-, GT28-, G25- or T3/T04E-class turbo; moderate-boost K- and B-series builds of roughly 400–550 whp using GT30/GTX30-, G25-660/G30-, Precision 5558–6266- or EFR-class turbos; and fully built, sleeved drag and time-attack engines running 25–45 psi on E85 or race fuel. Honda publishes no "safe power on stock internals" figure for any of these engines. Every such figure on this page is a tuner estimate, vendor claim or owner report and is marked as such. Power figures are wheel horsepower (whp) unless stated.

Engines and how they tolerate boost

The common failure on a boosted stock Honda bottom end is detonation damage to the cast pistons (cracked ring lands), not a broken block. Compression ratio, fuel quality, intake temperature and knock control decide how much boost a given engine survives far more than any single psi figure. The table below summarises the most widely repeated stock-internal estimates; none comes from Honda.

EngineBore × stroke (mm)CompressionMost repeated stock-internal estimateUsual first failure
D16Y7/Y8/Z675 × 909.1–9.6:1About 200–220 whp (owner consensus)Rods and rod bolts, cast pistons
B16A/B18C81 × 77.4 / 87.210.0–11.1:1About 300–350 whp (owner reports)Ring lands under detonation
B18B (LS)81 × 899.2:1Mild boost only on stock pistons and sleeves (owner advice of about 10 psi)Ring lands; rods at higher rpm
K20A2/K20Z1/K20Z386 × 8611.0:1About 400 whp (HP Academy estimate)Ring lands; high compression limits boost
K24A1/A4/A8/Z187 × 999.6–9.7:1About 450 whp (HP Academy estimate)Ring lands; rods at high rpm
K24A287 × 9910.5:1About 450 whp (HP Academy estimate)Ring lands
H22A87 × 90.710.0–11.0:1About 300–350 whp (owner estimates)Ring lands; FRM bores limit piston choice
F20C87 × 8411.0–11.7:1About 400–440 whp at 15–18 psi reported on stock blocksHigh compression requires a careful tune

K20 and K24

Both share an open-deck aluminium block with cast-in iron liners and a bedplate, a DOHC 16-valve head with intake cam phasing (VTC) and i-VTEC. Two head families matter for boost. "Performance" heads switch VTEC on both camshafts: K20A, K20A2, K20Z1, K20Z3, K20Z4, K24A2 and the TSX K24Z3. "Economy" heads switch VTEC on the intake cam only: K20A3, K24A1, K24A4, K24A8, K24Z1 and the direct-injection K24W. The K24A2 is therefore a dual-VTEC engine, contrary to a common assumption.

The most-cited estimates, from HP Academy, are about 400 whp for a K20 and about 450 whp for a K24 on stock internals with a good tune, adequate fuel and effective knock control. Aftermarket rods and pistons raise that to about 600–700 whp, beyond which the open deck becomes the limit and sleeves or block guards are used. Owner claims of 500–600 whp on stock engines exist but are single cases. One conservative source puts the safe figure as low as about 300 whp. Low-compression K24 blocks (A1/A4/A8/Z1, 9.6–9.7:1) are preferred over the 11:1 performance engines for stock-bottom-end turbo builds because of their larger detonation margin. The K20A2 has piston oil squirters and a factory oil cooler; the economy blocks lack squirters.

Rod vendors describe the naturally aspirated K-series rods as powder metal, but no Honda statement confirming the rod material for each engine code has been found. By contrast, Honda's own description of the factory-turbo K20C1 (FK8/FL5 Civic Type R) specifies 9.8:1 compression, a forged crankshaft, forged one-piece rods, piston oil jets, sodium-filled exhaust valves and about 23 psi peak boost, which shows what Honda considered necessary for sustained boost on this architecture.

K20 head on K24 block (the "K24 mod" or "frankenstein")

The K20/K24 hybrid fits a K20 performance head (K20A, K20A2, K20Z1 or K20Z3) to a K24 block, combining the K24's 2.4 litres and 99 mm stroke with the better-flowing K20 head. Retailer piston listings give both heads a combustion chamber of about 50.5 cc, so the hybrid keeps the K24 piston's compression: about 9.6:1 with A1 pistons, 9.7:1 with A4/A8/Z1 pistons and 10.5:1 with A2 pistons. A stock K24A1, A4 or A8 bottom end with a K20 head is therefore a ready-made low-compression turbo base, although the hybrid is also widely built naturally aspirated.

  • Block: K24A-series blocks are the documented base. Hybrid Racing's build guide states that Z-series blocks are not supported, and other guides agree; forum builds on Z blocks exist but no reliable procedure has been published.
  • Taller-deck parts: K24 head gasket (87 mm bore), K24 timing chain, K24 front cover and dipstick. The K24 deck is 231.5 mm against 212 mm for the K20.
  • Oiling: the K20A2 water-pump housing carries an oil-cooler port, which must be retained with the housing, deleted or plumbed to an external cooler. Builds that fit a K20A/A2 or F20C oil pump to delete the K24 balance shafts must trim the pump body and remove and plug the K24 balance-shaft oil jet (restrictor orifice, given in a forum thread as 11135-PNA-000).
  • Cam phasing: the K24 VTC gear can be retained, or the 50° gear from the JDM K20A Type R can replace the 25° gear for more midrange.
  • Piston-to-valve clearance: K24A4 and K24A8 pistons contact K20 head valves; A1/A2 or aftermarket pistons are used instead. Aggressive cams or the 50° VTC gear reduce clearance further, so a clay check is advised.
  • Management: an aftermarket ECU, typically Hondata K-Pro, to run the K20 cams, VTEC point and VTC map on the larger displacement.

The K24's longer stroke gives a lower rod-to-stroke ratio (about 1.54 against 1.62 for the K20), raising piston speed and side-loading. This is one reason boosted K24 builds limit rpm or fit forged rods. No hybrid-specific power limit has been published; the K24 estimates above apply. A separate race-engine configuration runs an OEM K24 crankshaft in a K20 block with custom rods or pistons.

B-series and LS/VTEC

The LS/VTEC hybrid fits a DOHC VTEC head (B16A, B17A or B18C) to the non-VTEC B18A/B18B "LS" block, or to a B20 block ("B20VTEC"). The LS block is cheap, has the longest B18 stroke (89 mm, 1,834 cc) and a low stock compression of about 9.5:1 with a VTEC head, which suits boost. The conversion needs an external VTEC oil feed from a sandwich plate or sender tee to the head (the head's deck passage is plugged), LS/VTEC alignment dowels, GSR/ITR-length head studs, and a GSR/ITR or LS timing belt with the matching water pump: the B16 belt does not fit the taller block. Head-gasket choice is disputed; one detailed guide insists on the OEM LS gasket because a VTEC gasket can leak at the gallery hole the LS block lacks.

Owner reports put cast ring-land failure at around 300–350 whp and the factory liners as unreliable above about 400–500 whp even with forged pistons and rods. Beyond that, Darton MID or Golden Eagle sleeves are standard. A documented B18C1 at about 1,200 hp used Golden Eagle sleeves, Wiseco pistons and CP-Carrillo rods.

D-series

The D16 is the cheapest platform: common, low in compression (9.1–9.6:1) and simple. The usual hybrid, the "mini-me", fits a SOHC VTEC head (D16Z6 or D16Y8) to a non-VTEC D16Y7 block and stays close to the Y7's 9.4:1; the thicker Z6 head gasket is suggested for turbo use. Owner consensus puts the stock rods and rod bolts at about 200–220 whp, and the D16Y8 bottom end is described as prone to spinning rod bearings under boost. Above that, rods and pistons are replaced, and sleeving is needed for high boost.

Engine management

B, D and H-series: OBD1 Honda ECUs

Turbo B, D and H builds almost always run a 1992–95 OBD1 Keihin ECU, even in 1996–2001 cars, which use an OBD2a (1996–98) or OBD2b (1999–2001) to OBD1 jumper harness because the OBD1 tuning tools are far more mature. The P28 (1992–95 Civic Si/EX; VTEC, no knock control) is the standard tuning base. The P30 adds knock control, and the P72 (1994–95 Integra GS-R) adds knock and intake air bypass control, so it is chosen where those are wanted. Hondata's s300 supports the P06, P28, P30, P61, P72, P74, P75 and PR4 (manual transmission only), with the s300j for JDM ECUs; the H22 Prelude P13/P14 ECUs are not supported, so H-series builds use a P28/P72-type ECU through a conversion harness. Other routes are a socketed ECU with Neptune RTP and a Moates Demon2, eCtune, Crome or Uberdata. Moates describes Neptune as actively developed and Crome and eCtune as less well maintained.

US OBD1 ECUs carry the circuit footprint but not the components for a PWM boost-control output. Hondata's s300 instructions wire the boost solenoid to pin A11 on US ECUs (A17 on JDM ECUs), using a three-port solenoid drawing no more than 3 A, with no relay between ECU and solenoid, and an ECU boost cut in case of solenoid or hose failure.

K-series ECUs

  • Hondata K-Pro (v4): installed in 2002–04 ECUs (RSX Type-S PRB A01–A12 and 305, PND, EP3 Civic Si PNF, PRA, PRC, PRD, PPA, PPL). Hondata documents fuel and ignition tables to 60 psi and 11,000 rpm, support for MAP sensors to 5 bar and above, a PWM boost-control output, gear-based corrections, an ethanol input and launch control with anti-lag. Manual transmission only.
  • 2005–06 RSX ECUs (PRB-A13 to A16) have a different processor and cannot take a K-Pro; Hondata supplies a modified 2002–04 ECU and adapter harness instead. KTuner's in-ECU board is built on exactly these 2005–06 ECUs and does not support the 2002–04 units.
  • Drive-by-wire cars (2006–11 Civic Si, TSX, 2006–09 S2000 and later K24 cars) cannot run a K-Pro. They are reflashed with Hondata FlashPro or KTuner Flash V2. On the 2006–11 Civic Si, FlashPro offers AFM, MAP or hybrid load tables, boost control, anti-lag and an ethanol input; Hondata lists 4 bar MAP support (about 43 psi) for the TSX. Engine swaps of drive-by-wire engines onto K-Pro convert to a cable throttle and K20A2-style harness.
  • Immobiliser: US K-series ECUs will not power the fuel pump or coils in a swap without a bypass box, the K-Pro software disable, or a JDM PRC ECU.

MAP sensor, injectors and IAT

Hondata gives the stock Honda MAP sensor's limit as about 10.5 psi of boost, so the boost cut must sit below that on a stock sensor. Common replacements are the Skunk2 and Omni 2.5 bar sensors, 3–4 bar units from Omni, SpeedFactory, Skunk2 and K-Tuned, the remote-mounted AEM 3.5 bar, and Hondata 4 bar and 7 bar sensors; each needs matching scalar and offset settings in the ECU. No Honda OEM 2.5 bar sensor has been identified. On the K-series, the Acura RDX injector (410 cc/min at 38 psi, a plug-in high-impedance part) is the usual first upgrade; 1,000–1,050 cc injectors cover the 400–600 bhp class. Honda OBD1 and OBD2 ECUs drive high-impedance injectors, so older low-impedance injectors need a resistor box. Hondata advises relocating the IAT sensor to read air after the turbo, usually in the charge pipe before the throttle body.

Standalone ECUs

Builders move to a standalone ECU for drive-by-wire on unsupported platforms, high injector or output counts, CAN dash and power-distribution integration, multi-axis closed-loop boost and race features. Plug-in options include the Haltech Nexus plug-in HT-231001 for EP3/DC5 (onboard 4 bar MAP), the Haltech Elite with plug-in adaptors (the Elite 2500 is required to retain drive-by-wire on the AP2 S2000), the Link G4X CIVICLink K20X (HC20X) and HC92X for OBD1 B-series, the AEM Series 2 and Infinity, and MoTeC M1 with custom harnesses. Many 400–500 whp K24 turbo builds still run a K-Pro.

Exhaust manifolds

LayoutDescription and use
Cast log / stock locationShort cast-iron manifold placing the turbo where the factory header sits. Used in budget kits and the old GReddy and HKS kits. Compact and quick to warm but restrictive at high power.
Ramhorn (cast or tubular)Runners curve to a central turbine flange low at the front of the head. Common on B/D-series and the 2006–11 Civic Si.
Top mountRunners rise to a flange above the head; allows larger turbos and 4" downpipes but needs bonnet, firewall and sometimes steering clearance.
SidewinderK-series layout that turns the runners toward the gearbox end and places the turbo over the transmission. The usual layout for K20/K24 builds in EP3, DC5, RSX and K-swapped chassis.
Rear mountNo current bolt-on Honda rear-mount kit has been identified.

Turbine flanges range from T25/T28 for small Garrett frames, through T3 for most budget and mid-range kits, to T4 open or divided and V-band for larger turbos; several top-mount manifolds are drilled for both T3 and T4. Fabricated manifolds carry external wastegates, typically 38 mm on budget kits, 44–46 mm V-band on most branded manifolds and 60 mm or twin gates on large sidewinders and top mounts. Established fabricated-manifold makers include SpeedFactory Racing (1.5" schedule 40 stainless with 1/2" flanges, vendor listing), PLM, Full-Race, Blox (schedule 40 T304) and, in the UK, Tegiwa (its own 304 sidewinder for a T3 turbo and 45 mm V-band gate) and Tuning Developments (T3 sidewinder with 44 mm gate, sold by Pro-Race Engineering at £750 inc VAT, seen 19 November 2026). Sources conflict on whether the Tegiwa manifold uses schedule 10 or schedule 40 tube.

Most fabricated Honda manifolds are 304 stainless. No mainstream Honda manifold is advertised in 321, and no controlled comparison of cracking between the grades, or between cast SiMo and Ni-resist irons, exists for these applications. Schedule 40 tube is heavier and slower to heat but generally regarded as more crack-resistant than schedule 10.

  • Cracking: owner reports describe GReddy RSX and S2000 kit manifolds as prone to cracking, and an early Inline Pro S2000 sidewinder cracked in the base metal. Owners attribute such failures to a missing manifold-to-block brace, no flex section in the downpipe, an unsupported dump tube and thin early wastegate flanges. Reports exist for budget and premium manifolds alike; there is no evidence that budget manifolds crack measurably more often.
  • Wastegate creep: a 90° wastegate entry on K-series sidewinders, combined with the engine's high volumetric efficiency and a free-flowing turbine, is linked to boost overshooting the spring pressure; one documented case overshot a 10 psi spring to a 24 psi boost cut. Fixes are a teardrop entry at about 45°, a larger or second gate, or a "wastegate-priority" sidewinder.
  • Warranty: SpeedFactory's warranty covers welding defects only and excludes manifolds that have been heat-wrapped or fitted with an improper downpipe or dump tube.

Turbo kits

No premium kit examined includes fuel-system parts or engine management; these are always bought separately. Prices below are as listed on 19 November 2026 unless stated.

KitApplicationTurbo and manifoldNotes
Full-Race FG2/FA5 Civic Si2006–11 Civic Si K20Z3T3/T04E 57-trim, GT2871R, GT3076R, GT3582R or HTA3586R on a T3 tubular manifold, TiAL 44 mm gateManufacturer claims about 350 whp (57-trim) to 430–440 whp (GT3582R) on a stock K20Z3 at 11–12 psi on 91–93 octane. Not listed in Full-Race's store when checked; availability not established.
Full-Race FK8 (sold by 4 Piston)K20C1 Civic Type RUpgrade turbo on V-band; OEM electronic wastegate retainedUS$2,782.99, sold out.
GReddy T517Z2002–03 RSX Type-ST517Z internal-gate turbo on a cast-iron manifold, preset about 8.5 psiIncluded 440 cc injectors and an e-Manage piggyback. Reported discontinued.
HKS2002–04 RSX Type-SGT2835 ball-bearing, internal gate, cast manifoldReported discontinued.
PTuning S2000S2000GT3076R standard (GT3582R/GTX options), T304 V-band manifoldUS$7,430 base; no fuel or tune.
Inline Pro Stage 2 RaceS2000Precision journal-bearing turbo, T4 front mountUS$5,999; oil-filter relocation extra.
Rev9 TCK-001 / 002 / 003RSX and EP3 / B-series / D-seriesTX-50E-57 T3 turbo on cast manifolds, 38 mm 7 psi gateAbout US$770–1,400. Owner reviews cite missing or poor hardware rather than manifold failure.
CXRacingDC5/RSX, B- and D-seriesGT35-type turbo on sidewinder or ramhorn; cast D-series kitK20 kit about US$1,299 without intercooler (search listing only).

Budget kits (Rev9, CXRacing, JDM Performance, Bull Boost and unbranded online kits) cost roughly a third to a half of a premium kit. Owner reviews consistently report short studs, torn gaskets, generic bolts, missing parts and piping that needs modification. Several brands often associated with Honda turbo builds do not make Honda turbo kits: Kraftwerks sells Rotrex supercharger kits; Hondata makes engine management only; 4 Piston Racing retails the Full-Race FK8 kit; and Hybrid Racing retails SpeedFactory manifolds. No turbo manifold or kit from K-Tuned, ISR Performance or DC Sports has been found, although K-Tuned sells a timing-chain tensioner cover with a -10AN turbo oil return. No complete UK-manufactured K-series kit has been identified; UK builds normally combine a UK-sold or imported manifold with a separately bought turbo.

Supporting parts

  • Oil feed and drain: the feed is usually tapped from the oil-pressure-switch port or filter-housing area. The drain must fall continuously by gravity into the sump above the oil level, through a welded or bolt-on -10AN sump bung or, on K20A/K20Z/K24A engines, a timing-chain tensioner cover with a -10AN return (not K24Z). Poor drainage produces smoke through the turbo seals.
  • Fuel pump: a Walbro 255 l/h in-tank pump is the usual first step; owner reports put its practical limit at about 450 whp, against vendor claims of about 600 hp. An AEM 340 or 400 l/h pump is used beyond that. The EP3/RSX-generation K20 fuel system is returnless, which one UK supplier describes as a restriction around 400 bhp.
  • Intercooler and exhaust: 2.5"-thick cores suit about 500 bhp; 3" V-band downpipes with a flex section are standard.
  • Clutch: six-puck ceramic single-plate clutches are recommended for higher-power K-series builds and twin-plate clutches from about 500 whp.

Common turbochargers

Garrett states that its horsepower ratings are flywheel-equivalent figures calculated from compressor choke flow, so they describe compressor capacity, not likely wheel power. Precision and BorgWarner ratings are similar maximum-capability claims.

TurboCompressor inducer/exducer (mm)Published ratingTypical Honda use
Garrett GT2560R / GT2860RS46/60, 47/60170–270 hp / 250–360 hpD16 and B16 low boost
T3/T04E 50–57 trim53.9–56.6 inducerKit-maker figures of about 420–460 whpClassic D/B-series kit turbo at 8–15 psi
Garrett G25-550 / G25-66048/60, 54/67300–550 hp / 350–660 hpB-series and stock-internal K24 street builds
Garrett GT3076R57/76310–525 hpLong-time default for B18/B20, K20/K24 and F20C at 300–450 whp
Garrett GTX3076R Gen II / G30-77058/76, 58/71400–750 hp / 475–770 hpK20/K24 at 400–550 whp; built K-series
Precision Gen2 5558 / 6062 / 626655, 60, 62 inducer650 / 750 / 800 hpB/K-series 400–650 whp; built engines
BorgWarner EFR 6758 / 716354/67, 57/71500 / 550 hp peakK-series street (Full-Race kits)
Garrett GTX3582R Gen II, G35, Precision 6870 and larger66/82 and up450–900 hp and upBuilt and drag K/B-series

Budget alternatives include unbranded T3/T4 hybrids, second-hand Holset HX35 diesel turbos on B-series and Pulsar G-series replicas; their specifications rest on seller claims or forum measurements. Smaller turbine housings (about 0.6 A/R) favour response and larger ones (0.8–1.0 A/R) favour top-end power.

Reported power results

For comparison, Acura rated the B18C1 at 170 hp; the K20A2 is quoted at 200 hp and the K24A2 at 200–205 hp (the later figure under a revised SAE method), and the D16Y8 at about 127 hp.

EngineInternalsTurboBoost and fuelResultEvidence
D16 (various)StockSmall T3 / kit turbos6–8 psiAbout 150–210 whpOwner reports
D16Z6Built, Darton sleevesPrecision 626228 psi, E85717 whp, Mustang dynoMagazine spec sheet
B18CStockPrecision 5457, T3/T04E 57-trim8–12 psiAbout 300–370 whp; 410 whp on race fuelOwner reports; one B16B piston failure at 10 psi
B18C1Built, Golden Eagle sleevesPTE 728045 psi, race fuel983 whp, DynojetMagazine spec sheet
K24Z3StockGarrett G25-66012 psi, E85470 whpBuilder report
K20Z3Stock (junkyard engine)Not identified18.5 psi503, then 530 whpBlog build series; source excerpts only
K24Z7Not statedGarrett GTX3076RAbout 15 psi, 93 octane400.85 whpShop report
K24A2BuiltBorgWarner S300SX318 psi, 92 octane520 whp, DynapackMagazine spec sheet
K20Stock sleeves, forged pistons and rodsPrecision 626528 psi, E85745 whpShop report
K20ABuilt, Golden Eagle sleevesGarrett GTX3586RS40 psi, E85874 whp, DynapackMagazine spec sheet
K24 (4 Piston)Built, ductile sleevesPrecision PT7285About 30–33 psi, E851,038–1,042 hp; wheel or crank not statedBuilder figure, two reports
K-series drag CivicBuiltPrecision GT42R42 psi, race fuel1,125 whp, DynapackMagazine spec sheet
F20CStock internals, ARP studsGarrett GT3076R15 psi, 93 octane431 whp, Dyno DynamicsMagazine
H22Stock cams, 10:1Not stated16 psi439 whpOwner report
F22C1Built, Golden Eagle sleevesPrecision 646645 psi, race fuel961 whp, Mainline hub dynoMagazine spec sheet

The documented stock-internal K-series results support roughly 450–530 whp as achievable but at risk; the frequently quoted "350–450 whp on a stock K" is a consistent community generalisation rather than a tested limit. Every result above about 550 whp found comes from a sleeved or forged engine on E85 or race fuel at 25–45 psi.

Comparing power figures

  • Forum posts often give "hp" without stating wheel or crank, and builder engine-dyno figures cannot be compared with chassis-dyno wheel figures.
  • Mustang (loaded) dynos are reported to read about 5–15% below Dynojet inertia dynos; hub dynos such as Dynapack and Mainline produced several of the headline figures above.
  • UK rolling roads usually report a flywheel estimate from a coast-down measurement or a fixed loss (about 15% is commonly used), so a UK flywheel figure is not directly comparable with a US wheel figure.

Not established

  • Rod material (forged or powder metal) for each naturally aspirated K20/K24 engine code, and any measured failure threshold for stock K, B or D internals.
  • Whether K24Z blocks are suitable for the K20 head hybrid, and K20/K24 exhaust-flange compatibility across head codes.
  • The stock-internal limit of the K20C1.
  • Current availability of Full-Race's RSX, FG2/FA5 and S2000 kits, and official discontinuation of the GReddy and HKS RSX kits.
  • UK rolling-road results for turbo Honda engines with full specifications.

Related pages

Sources

All sources accessed 19 November 2026. "Undated" means no publication date was shown. Sources marked "search excerpt" refused automated access; their content was read from search-engine results and may be stale.

Manufacturer documentation

Technical articles and build guides

Dyno results and build reports

Vendor listings

Owner discussions

Revision 2: Honda turbo conversions: engines, ECUs, manifolds, kits and results

Turbocharging the naturally aspirated Honda D-series, B-series, K-series (K20 and K24), H22 and F20C/F22C engines is one of the most widely documented forced-induction conversions. Builds fall into three broad groups: low-boost conversions on stock internals using a small T25/T28-, GT28-, G25- or T3/T04E-class turbo; moderate-boost K- and B-series builds of roughly 400–550 whp using GT30/GTX30-, G25-660/G30-, Precision 5558–6266- or EFR-class turbos; and fully built, sleeved drag and time-attack engines running 25–45 psi on E85 or race fuel. Honda publishes no "safe power on stock internals" figure for any of these engines. Every such figure on this page is a tuner estimate, vendor claim or owner report and is marked as such. Power figures are wheel horsepower (whp) unless stated.

Engines and how they tolerate boost

The common failure on a boosted stock Honda bottom end is detonation damage to the cast pistons (cracked ring lands), not a broken block. Compression ratio, fuel quality, intake temperature and knock control decide how much boost a given engine survives far more than any single psi figure. The table below summarises the most widely repeated stock-internal estimates; none comes from Honda.

EngineBore × stroke (mm)CompressionMost repeated stock-internal estimateUsual first failure
D16Y7/Y8/Z675 × 909.1–9.6:1About 200–220 whp (owner consensus)Rods and rod bolts, cast pistons
B16A/B18C81 × 77.4 / 87.210.0–11.1:1About 300–350 whp (owner reports)Ring lands under detonation
B18B (LS)81 × 899.2:1Mild boost only on stock pistons and sleeves (owner advice of about 10 psi)Ring lands; rods at higher rpm
K20A2/K20Z1/K20Z386 × 8611.0:1About 400 whp (HP Academy estimate)Ring lands; high compression limits boost
K24A1/A4/A8/Z187 × 999.6–9.7:1About 450 whp (HP Academy estimate)Ring lands; rods at high rpm
K24A287 × 9910.5:1About 450 whp (HP Academy estimate)Ring lands
H22A87 × 90.710.0–11.0:1About 300–350 whp (owner estimates)Ring lands; FRM bores limit piston choice
F20C87 × 8411.0–11.7:1About 400–440 whp at 15–18 psi reported on stock blocksHigh compression requires a careful tune

K20 and K24

Both share an open-deck aluminium block with cast-in iron liners and a bedplate, a DOHC 16-valve head with intake cam phasing (VTC) and i-VTEC. Two head families matter for boost. "Performance" heads switch VTEC on both camshafts: K20A, K20A2, K20Z1, K20Z3, K20Z4, K24A2 and the TSX K24Z3. "Economy" heads switch VTEC on the intake cam only: K20A3, K24A1, K24A4, K24A8, K24Z1 and the direct-injection K24W. The K24A2 is therefore a dual-VTEC engine, contrary to a common assumption.

The most-cited estimates, from HP Academy, are about 400 whp for a K20 and about 450 whp for a K24 on stock internals with a good tune, adequate fuel and effective knock control. Aftermarket rods and pistons raise that to about 600–700 whp, beyond which the open deck becomes the limit and sleeves or block guards are used. Owner claims of 500–600 whp on stock engines exist but are single cases. One conservative source puts the safe figure as low as about 300 whp. Low-compression K24 blocks (A1/A4/A8/Z1, 9.6–9.7:1) are preferred over the 11:1 performance engines for stock-bottom-end turbo builds because of their larger detonation margin. The K20A2 has piston oil squirters and a factory oil cooler; the economy blocks lack squirters.

Rod vendors describe the naturally aspirated K-series rods as powder metal, but no Honda statement confirming the rod material for each engine code has been found. By contrast, Honda's own description of the factory-turbo K20C1 (FK8/FL5 Civic Type R) specifies 9.8:1 compression, a forged crankshaft, forged one-piece rods, piston oil jets, sodium-filled exhaust valves and about 23 psi peak boost, which shows what Honda considered necessary for sustained boost on this architecture.

K20 head on K24 block (the "K24 mod" or "frankenstein")

The K20/K24 hybrid fits a K20 performance head (K20A, K20A2, K20Z1 or K20Z3) to a K24 block, combining the K24's 2.4 litres and 99 mm stroke with the better-flowing K20 head. Retailer piston listings give both heads a combustion chamber of about 50.5 cc, so the hybrid keeps the K24 piston's compression: about 9.6:1 with A1 pistons, 9.7:1 with A4/A8/Z1 pistons and 10.5:1 with A2 pistons. A stock K24A1, A4 or A8 bottom end with a K20 head is therefore a ready-made low-compression turbo base, although the hybrid is also widely built naturally aspirated.

  • Block: K24A-series blocks are the documented base. Hybrid Racing's build guide states that Z-series blocks are not supported, and other guides agree; forum builds on Z blocks exist but no reliable procedure has been published.
  • Taller-deck parts: K24 head gasket (87 mm bore), K24 timing chain, K24 front cover and dipstick. The K24 deck is 231.5 mm against 212 mm for the K20.
  • Oiling: the K20A2 water-pump housing carries an oil-cooler port, which must be retained with the housing, deleted or plumbed to an external cooler. Builds that fit a K20A/A2 or F20C oil pump to delete the K24 balance shafts must trim the pump body and remove and plug the K24 balance-shaft oil jet (restrictor orifice, given in a forum thread as 11135-PNA-000).
  • Cam phasing: the K24 VTC gear can be retained, or the 50° gear from the JDM K20A Type R can replace the 25° gear for more midrange.
  • Piston-to-valve clearance: K24A4 and K24A8 pistons contact K20 head valves; A1/A2 or aftermarket pistons are used instead. Aggressive cams or the 50° VTC gear reduce clearance further, so a clay check is advised.
  • Management: an aftermarket ECU, typically Hondata K-Pro, to run the K20 cams, VTEC point and VTC map on the larger displacement.

The K24's longer stroke gives a lower rod-to-stroke ratio (about 1.54 against 1.62 for the K20), raising piston speed and side-loading. This is one reason boosted K24 builds limit rpm or fit forged rods. No hybrid-specific power limit has been published; the K24 estimates above apply. A separate race-engine configuration runs an OEM K24 crankshaft in a K20 block with custom rods or pistons.

B-series and LS/VTEC

The LS/VTEC hybrid fits a DOHC VTEC head (B16A, B17A or B18C) to the non-VTEC B18A/B18B "LS" block, or to a B20 block ("B20VTEC"). The LS block is cheap, has the longest B18 stroke (89 mm, 1,834 cc) and a low stock compression of about 9.5:1 with a VTEC head, which suits boost. The conversion needs an external VTEC oil feed from a sandwich plate or sender tee to the head (the head's deck passage is plugged), LS/VTEC alignment dowels, GSR/ITR-length head studs, and a GSR/ITR or LS timing belt with the matching water pump: the B16 belt does not fit the taller block. Head-gasket choice is disputed; one detailed guide insists on the OEM LS gasket because a VTEC gasket can leak at the gallery hole the LS block lacks.

Owner reports put cast ring-land failure at around 300–350 whp and the factory liners as unreliable above about 400–500 whp even with forged pistons and rods. Beyond that, Darton MID or Golden Eagle sleeves are standard. A documented B18C1 at about 1,200 hp used Golden Eagle sleeves, Wiseco pistons and CP-Carrillo rods.

D-series

The D16 is the cheapest platform: common, low in compression (9.1–9.6:1) and simple. The usual hybrid, the "mini-me", fits a SOHC VTEC head (D16Z6 or D16Y8) to a non-VTEC D16Y7 block and stays close to the Y7's 9.4:1; the thicker Z6 head gasket is suggested for turbo use. Owner consensus puts the stock rods and rod bolts at about 200–220 whp, and the D16Y8 bottom end is described as prone to spinning rod bearings under boost. Above that, rods and pistons are replaced, and sleeving is needed for high boost.

Engine management

B, D and H-series: OBD1 Honda ECUs

Turbo B, D and H builds almost always run a 1992–95 OBD1 Keihin ECU, even in 1996–2001 cars, which use an OBD2a (1996–98) or OBD2b (1999–2001) to OBD1 jumper harness because the OBD1 tuning tools are far more mature. The P28 (1992–95 Civic Si/EX; VTEC, no knock control) is the standard tuning base. The P30 adds knock control, and the P72 (1994–95 Integra GS-R) adds knock and intake air bypass control, so it is chosen where those are wanted. Hondata's s300 supports the P06, P28, P30, P61, P72, P74, P75 and PR4 (manual transmission only), with the s300j for JDM ECUs; the H22 Prelude P13/P14 ECUs are not supported, so H-series builds use a P28/P72-type ECU through a conversion harness. Other routes are a socketed ECU with Neptune RTP and a Moates Demon2, eCtune, Crome or Uberdata. Moates describes Neptune as actively developed and Crome and eCtune as less well maintained.

US OBD1 ECUs carry the circuit footprint but not the components for a PWM boost-control output. Hondata's s300 instructions wire the boost solenoid to pin A11 on US ECUs (A17 on JDM ECUs), using a three-port solenoid drawing no more than 3 A, with no relay between ECU and solenoid, and an ECU boost cut in case of solenoid or hose failure.

K-series ECUs

  • Hondata K-Pro (v4): installed in 2002–04 ECUs (RSX Type-S PRB A01–A12 and 305, PND, EP3 Civic Si PNF, PRA, PRC, PRD, PPA, PPL). Hondata documents fuel and ignition tables to 60 psi and 11,000 rpm, support for MAP sensors to 5 bar and above, a PWM boost-control output, gear-based corrections, an ethanol input and launch control with anti-lag. Manual transmission only.
  • 2005–06 RSX ECUs (PRB-A13 to A16) have a different processor and cannot take a K-Pro; Hondata supplies a modified 2002–04 ECU and adapter harness instead. KTuner's in-ECU board is built on exactly these 2005–06 ECUs and does not support the 2002–04 units.
  • Drive-by-wire cars (2006–11 Civic Si, TSX, 2006–09 S2000 and later K24 cars) cannot run a K-Pro. They are reflashed with Hondata FlashPro or KTuner Flash V2. On the 2006–11 Civic Si, FlashPro offers AFM, MAP or hybrid load tables, boost control, anti-lag and an ethanol input; Hondata lists 4 bar MAP support (about 43 psi) for the TSX. Engine swaps of drive-by-wire engines onto K-Pro convert to a cable throttle and K20A2-style harness.
  • Immobiliser: US K-series ECUs will not power the fuel pump or coils in a swap without a bypass box, the K-Pro software disable, or a JDM PRC ECU.

MAP sensor, injectors and IAT

Hondata gives the stock Honda MAP sensor's limit as about 10.5 psi of boost, so the boost cut must sit below that on a stock sensor. Common replacements are the Skunk2 and Omni 2.5 bar sensors, 3–4 bar units from Omni, SpeedFactory, Skunk2 and K-Tuned, the remote-mounted AEM 3.5 bar, and Hondata 4 bar and 7 bar sensors; each needs matching scalar and offset settings in the ECU. No Honda OEM 2.5 bar sensor has been identified. On the K-series, the Acura RDX injector (410 cc/min at 38 psi, a plug-in high-impedance part) is the usual first upgrade; 1,000–1,050 cc injectors cover the 400–600 bhp class. Honda OBD1 and OBD2 ECUs drive high-impedance injectors, so older low-impedance injectors need a resistor box. Hondata advises relocating the IAT sensor to read air after the turbo, usually in the charge pipe before the throttle body.

Standalone ECUs

Builders move to a standalone ECU for drive-by-wire on unsupported platforms, high injector or output counts, CAN dash and power-distribution integration, multi-axis closed-loop boost and race features. Plug-in options include the Haltech Nexus plug-in HT-231001 for EP3/DC5 (onboard 4 bar MAP), the Haltech Nexus Rebel K (kit HT-220206: ECU HT-220003 with the HT-186402 terminated main harness for K20A, K24A and K24Z engines, sold for manual-transmission applications, with injector, throttle and transmission sub-harnesses separate), the Haltech Elite with plug-in adaptors (the Elite 2500 is required to retain drive-by-wire on the AP2 S2000), the Link G4X CIVICLink K20X (HC20X) and HC92X for OBD1 B-series, the AEM Series 2 and Infinity, and MoTeC M1 with custom harnesses. Many 400–500 whp K24 turbo builds still run a K-Pro.

Exhaust manifolds

LayoutDescription and use
Cast log / stock locationShort cast-iron manifold placing the turbo where the factory header sits. Used in budget kits and the old GReddy and HKS kits. Compact and quick to warm but restrictive at high power.
Ramhorn (cast or tubular)Runners curve to a central turbine flange low at the front of the head. Common on B/D-series and the 2006–11 Civic Si.
Top mountRunners rise to a flange above the head; allows larger turbos and 4" downpipes but needs bonnet, firewall and sometimes steering clearance.
SidewinderK-series layout that turns the runners toward the gearbox end and places the turbo over the transmission. The usual layout for K20/K24 builds in EP3, DC5, RSX and K-swapped chassis.
Rear mountNo current bolt-on Honda rear-mount kit has been identified.

Turbine flanges range from T25/T28 for small Garrett frames, through T3 for most budget and mid-range kits, to T4 open or divided and V-band for larger turbos; several top-mount manifolds are drilled for both T3 and T4. Fabricated manifolds carry external wastegates, typically 38 mm on budget kits, 44–46 mm V-band on most branded manifolds and 60 mm or twin gates on large sidewinders and top mounts. Established fabricated-manifold makers include SpeedFactory Racing (1.5" schedule 40 stainless with 1/2" flanges, vendor listing), PLM, Full-Race, Blox (schedule 40 T304) and, in the UK, Tegiwa (its own 304 sidewinder for a T3 turbo and 45 mm V-band gate) and Tuning Developments (T3 sidewinder with 44 mm gate, sold by Pro-Race Engineering at £750 inc VAT, seen 19 November 2026). Sources conflict on whether the Tegiwa manifold uses schedule 10 or schedule 40 tube.

Most fabricated Honda manifolds are 304 stainless. No mainstream Honda manifold is advertised in 321, and no controlled comparison of cracking between the grades, or between cast SiMo and Ni-resist irons, exists for these applications. Schedule 40 tube is heavier and slower to heat but generally regarded as more crack-resistant than schedule 10.

  • Cracking: owner reports describe GReddy RSX and S2000 kit manifolds as prone to cracking, and an early Inline Pro S2000 sidewinder cracked in the base metal. Owners attribute such failures to a missing manifold-to-block brace, no flex section in the downpipe, an unsupported dump tube and thin early wastegate flanges. Reports exist for budget and premium manifolds alike; there is no evidence that budget manifolds crack measurably more often.
  • Wastegate creep: a 90° wastegate entry on K-series sidewinders, combined with the engine's high volumetric efficiency and a free-flowing turbine, is linked to boost overshooting the spring pressure; one documented case overshot a 10 psi spring to a 24 psi boost cut. Fixes are a teardrop entry at about 45°, a larger or second gate, or a "wastegate-priority" sidewinder.
  • Warranty: SpeedFactory's warranty covers welding defects only and excludes manifolds that have been heat-wrapped or fitted with an improper downpipe or dump tube.

Turbo kits

No premium kit examined includes fuel-system parts or engine management; these are always bought separately. Prices below are as listed on 19 November 2026 unless stated.

KitApplicationTurbo and manifoldNotes
Full-Race FG2/FA5 Civic Si2006–11 Civic Si K20Z3T3/T04E 57-trim, GT2871R, GT3076R, GT3582R or HTA3586R on a T3 tubular manifold, TiAL 44 mm gateManufacturer claims about 350 whp (57-trim) to 430–440 whp (GT3582R) on a stock K20Z3 at 11–12 psi on 91–93 octane. Not listed in Full-Race's store when checked; availability not established.
Full-Race FK8 (sold by 4 Piston)K20C1 Civic Type RUpgrade turbo on V-band; OEM electronic wastegate retainedUS$2,782.99, sold out.
GReddy T517Z2002–03 RSX Type-ST517Z internal-gate turbo on a cast-iron manifold, preset about 8.5 psiIncluded 440 cc injectors and an e-Manage piggyback. Reported discontinued.
HKS2002–04 RSX Type-SGT2835 ball-bearing, internal gate, cast manifoldReported discontinued.
PTuning S2000S2000GT3076R standard (GT3582R/GTX options), T304 V-band manifoldUS$7,430 base; no fuel or tune.
Inline Pro Stage 2 RaceS2000Precision journal-bearing turbo, T4 front mountUS$5,999; oil-filter relocation extra.
Rev9 TCK-001 / 002 / 003RSX and EP3 / B-series / D-seriesTX-50E-57 T3 turbo on cast manifolds, 38 mm 7 psi gateAbout US$770–1,400. Owner reviews cite missing or poor hardware rather than manifold failure.
CXRacingDC5/RSX, B- and D-seriesGT35-type turbo on sidewinder or ramhorn; cast D-series kitK20 kit about US$1,299 without intercooler (search listing only).

Budget kits (Rev9, CXRacing, JDM Performance, Bull Boost and unbranded online kits) cost roughly a third to a half of a premium kit. Owner reviews consistently report short studs, torn gaskets, generic bolts, missing parts and piping that needs modification. Several brands often associated with Honda turbo builds do not make Honda turbo kits: Kraftwerks sells Rotrex supercharger kits; Hondata makes engine management only; 4 Piston Racing retails the Full-Race FK8 kit; and Hybrid Racing retails SpeedFactory manifolds. No turbo manifold or kit from K-Tuned, ISR Performance or DC Sports has been found, although K-Tuned sells a timing-chain tensioner cover with a -10AN turbo oil return. No complete UK-manufactured K-series kit has been identified; UK builds normally combine a UK-sold or imported manifold with a separately bought turbo.

Supporting parts

  • Oil feed and drain: the feed is usually tapped from the oil-pressure-switch port or filter-housing area. The drain must fall continuously by gravity into the sump above the oil level, through a welded or bolt-on -10AN sump bung or, on K20A/K20Z/K24A engines, a timing-chain tensioner cover with a -10AN return (not K24Z). Poor drainage produces smoke through the turbo seals.
  • Fuel pump: a Walbro 255 l/h in-tank pump is the usual first step; owner reports put its practical limit at about 450 whp, against vendor claims of about 600 hp. An AEM 340 or 400 l/h pump is used beyond that. The EP3/RSX-generation K20 fuel system is returnless, which one UK supplier describes as a restriction around 400 bhp.
  • Intercooler and exhaust: 2.5"-thick cores suit about 500 bhp; 3" V-band downpipes with a flex section are standard.
  • Clutch: six-puck ceramic single-plate clutches are recommended for higher-power K-series builds and twin-plate clutches from about 500 whp.

Common turbochargers

Garrett states that its horsepower ratings are flywheel-equivalent figures calculated from compressor choke flow, so they describe compressor capacity, not likely wheel power. Precision and BorgWarner ratings are similar maximum-capability claims.

TurboCompressor inducer/exducer (mm)Published ratingTypical Honda use
Garrett GT2560R / GT2860RS46/60, 47/60170–270 hp / 250–360 hpD16 and B16 low boost
T3/T04E 50–57 trim53.9–56.6 inducerKit-maker figures of about 420–460 whpClassic D/B-series kit turbo at 8–15 psi
Garrett G25-550 / G25-66048/60, 54/67300–550 hp / 350–660 hpB-series and stock-internal K24 street builds
Garrett GT3076R57/76310–525 hpLong-time default for B18/B20, K20/K24 and F20C at 300–450 whp
Garrett GTX3076R Gen II / G30-77058/76, 58/71400–750 hp / 475–770 hpK20/K24 at 400–550 whp; built K-series
Precision Gen2 5558 / 6062 / 626655, 60, 62 inducer650 / 750 / 800 hpB/K-series 400–650 whp; built engines
BorgWarner EFR 6758 / 716354/67, 57/71500 / 550 hp peakK-series street (Full-Race kits)
Garrett GTX3582R Gen II, G35, Precision 6870 and larger66/82 and up450–900 hp and upBuilt and drag K/B-series

Budget alternatives include unbranded T3/T4 hybrids, second-hand Holset HX35 diesel turbos on B-series and Pulsar G-series replicas; their specifications rest on seller claims or forum measurements. Smaller turbine housings (about 0.6 A/R) favour response and larger ones (0.8–1.0 A/R) favour top-end power.

Reported power results

For comparison, Acura rated the B18C1 at 170 hp; the K20A2 is quoted at 200 hp and the K24A2 at 200–205 hp (the later figure under a revised SAE method), and the D16Y8 at about 127 hp.

EngineInternalsTurboBoost and fuelResultEvidence
D16 (various)StockSmall T3 / kit turbos6–8 psiAbout 150–210 whpOwner reports
D16Z6Built, Darton sleevesPrecision 626228 psi, E85717 whp, Mustang dynoMagazine spec sheet
B18CStockPrecision 5457, T3/T04E 57-trim8–12 psiAbout 300–370 whp; 410 whp on race fuelOwner reports; one B16B piston failure at 10 psi
B18C1Built, Golden Eagle sleevesPTE 728045 psi, race fuel983 whp, DynojetMagazine spec sheet
K24Z3StockGarrett G25-66012 psi, E85470 whpBuilder report
K20Z3Stock (junkyard engine)Not identified18.5 psi503, then 530 whpBlog build series; source excerpts only
K24Z7Not statedGarrett GTX3076RAbout 15 psi, 93 octane400.85 whpShop report
K24A2BuiltBorgWarner S300SX318 psi, 92 octane520 whp, DynapackMagazine spec sheet
K20Stock sleeves, forged pistons and rodsPrecision 626528 psi, E85745 whpShop report
K20ABuilt, Golden Eagle sleevesGarrett GTX3586RS40 psi, E85874 whp, DynapackMagazine spec sheet
K24 (4 Piston)Built, ductile sleevesPrecision PT7285About 30–33 psi, E851,038–1,042 hp; wheel or crank not statedBuilder figure, two reports
K-series drag CivicBuiltPrecision GT42R42 psi, race fuel1,125 whp, DynapackMagazine spec sheet
F20CStock internals, ARP studsGarrett GT3076R15 psi, 93 octane431 whp, Dyno DynamicsMagazine
H22Stock cams, 10:1Not stated16 psi439 whpOwner report
F22C1Built, Golden Eagle sleevesPrecision 646645 psi, race fuel961 whp, Mainline hub dynoMagazine spec sheet

The documented stock-internal K-series results support roughly 450–530 whp as achievable but at risk; the frequently quoted "350–450 whp on a stock K" is a consistent community generalisation rather than a tested limit. Every result above about 550 whp found comes from a sleeved or forged engine on E85 or race fuel at 25–45 psi.

Comparing power figures

  • Forum posts often give "hp" without stating wheel or crank, and builder engine-dyno figures cannot be compared with chassis-dyno wheel figures.
  • Mustang (loaded) dynos are reported to read about 5–15% below Dynojet inertia dynos; hub dynos such as Dynapack and Mainline produced several of the headline figures above.
  • UK rolling roads usually report a flywheel estimate from a coast-down measurement or a fixed loss (about 15% is commonly used), so a UK flywheel figure is not directly comparable with a US wheel figure.

Not established

  • Rod material (forged or powder metal) for each naturally aspirated K20/K24 engine code, and any measured failure threshold for stock K, B or D internals.
  • Whether K24Z blocks are suitable for the K20 head hybrid, and K20/K24 exhaust-flange compatibility across head codes.
  • The stock-internal limit of the K20C1.
  • Current availability of Full-Race's RSX, FG2/FA5 and S2000 kits, and official discontinuation of the GReddy and HKS RSX kits.
  • UK rolling-road results for turbo Honda engines with full specifications.

Related pages

Sources

All sources accessed 19 November 2026. "Undated" means no publication date was shown. Sources marked "search excerpt" refused automated access; their content was read from search-engine results and may be stale.

Manufacturer documentation

Technical articles and build guides

Dyno results and build reports

Vendor listings

Owner discussions