This guide compares selected Ram 1500 and Jeep 3.0-litre EcoDiesel applications and HP Tuners reports about boost, fuel delivery, torque plausibility and gearbox behaviour. The ECU, software and transmission must be identified on the individual vehicle. Owner reports are diagnostic leads, not validated calibrations or interchangeable tune files.
Separate the 2015 Ram and 2020 Wrangler powertrains
Ram's US 2015 commercial specification identifies a 3.0-litre EcoDiesel V6 paired with the eight-speed 8HP70 automatic; the corresponding 2015 brochure lists 240 hp and 420 lb-ft in factory US specification. Jeep's 2020 Wrangler EcoDiesel specification lists a 3.0-litre diesel V6 and the eight-speed 8HP75 automatic; Jeep's announcement gives 260 hp and 442 lb-ft for that application. These are original vehicle examples, not safe tuning targets or proof of the transmission in a modified vehicle. Ram: 2015 commercial specifications; Ram: 2015 1500 brochure; Jeep: 2020 Wrangler specifications; Jeep: 2020 EcoDiesel announcement.
ECU and transmission support are different questions
HP Tuners lists the 2014-19 Grand Cherokee 3.0 EcoDiesel with EDC17C79 and the 2014-19 Ram 1500 3.0 EcoDiesel with EDC17C79, as well as separate 2020-23 Wrangler JL and 2021-23 Gladiator 3.0 entries. Its transmission listing also names selected ZF 8HP/8HP2 controllers. This does not establish that every 3.0 diesel or 8HP gearbox is supported: check exact VIN, market, controller and software, interface and separate TCM licence. HP Tuners: current Stellantis application list.
HP Tuners' PCM services page identifies the 2014-19 EDC17C79 as an exception to the general 2015+ send-in upgrade rule and says that controller updates on its first read to enable read/write. Its same page says Gen 3 EcoDiesel PCMs cannot be read before upgrade. These are different access paths; check the specific vehicle and current instructions with HP Tuners instead of assuming a first read is a passive backup or that all 2015+ units need the same service. Its 2018+ Smart Access Cable and separate module licensing requirements may also apply.
A 2021 Wrangler forum post reproduced a contemporary HP Tuners 2020 Ram/Wrangler EcoDiesel announcement and described a modified PCM, cable and inability to read a Gen 3 PCM before modification. It is historical context: device, price and support information can change; use the current manufacturer pages before buying or shipping a PCM.
A reported torque fault and a misleading lambda display
An EcoDiesel owner reported that VCM Scanner showed approximately 0.4 lambda at cruise on both stock and modified files, and reported torque-calculation and injector-control performance codes and engine cutout after making engine and transmission changes; the symptoms went away after returning both calibrations to stock. The vehicle year and controller version are not clearly identified, and the attached calibrations and log could not be examined. A torque deviation strategy and additional maps were suggested, but the exact corresponding HP Tuners table and a verified root cause were not established. EcoDiesel owner report.
Do not copy a percentage, raise a torque-plausibility threshold, or assume a displayed 0.4 means actual mixture: check the channel source, units, data validity, logger definition and calibration version with HP Tuners and compare with an independently validated measurement where appropriate. Simultaneous engine and TCM reversions do not isolate which change mattered.
The same report raises transient mixture limiting and emissions behaviour. Injection timing, fuel quantity, rail pressure and air supply interact with smoke and aftertreatment operation; a proposed generic increment is not evidence for a particular file or a substitute for measurements. Preserve factory diagnostics and emissions equipment, and check current service information and local requirements.
VCM Scanner: capture the event
- Record trouble codes and freeze-frame before a read; HP Tuners warns that reading a vehicle can clear codes. Document engine and TCM identification, current software, fuel, modifications, tyres, axle and towing load. Confirm the applicable pre-read/upgrade process and recovery support for that exact PCM. HP Tuners: VCM Editor starting procedure.
- Where the identified vehicle exposes meaningful channels, align engine speed, pedal and load, requested and actual rail pressure, airflow, manifold and barometric pressure, charge temperature, requested/estimated torque and torque-intervention status. Log actual and commanded gear, transmission temperature and converter-clutch command/slip if available. A requested quantity is not the measured response; check channel update rate and meaning. HP Tuners: Scanner configuration.
- Compare a repeatable baseline with a single documented change under similar temperature and load. Investigate fuel supply, sensors, wiring and mechanical faults against the appropriate service procedure before altering a calibration to conceal a code or limiting event. A shift request and physical clutch handover are different; a converter-clutch command alone does not prove lockup.
Interrupted write
A 2014 Jeep EcoDiesel owner reported that a laptop battery died during an HP Tuners-related update and the ECU could not be used. Recovery or replacement was proposed, but the final repair, a specific controller fault and the reliability of any recovery method were not established. Confirm power, stable communication and the manufacturer-approved recovery path before writing; if a write fails, stop and seek HP Tuners and vehicle-specific service guidance. A used ECU is not automatically programmed to the vehicle. 2014 Jeep EcoDiesel report.
Not established
The root cause of the torque-calculation codes and the outcome of the interrupted-write recovery are not documented, and the vehicle year and controller version of the torque case are unidentified.
Related: Ram pickup generations; Jeep Wrangler generations; VCM Scanner; HP Tuners MPVI4.