Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Chevrolet

Changes from revision 2 to revision 2

Removed text is struck through; added text is highlighted.

This guide uses the 2009 Chevrolet Cobalt SS Turbo and separately identified LNF-powered kit-car cases to explain HP Tuners pressure logging and direct-injection checks. A forum sensor label or tune from a different vehicle is not a verified definition for the car being worked on.

Identify engine, transmission and controller

Chevrolet's 2009 Cobalt US specification lists a 2.0-litre, 260-hp turbocharged DOHC engine in the SS Turbo coupe and sedan, with a five-speed manual; it does not list the automatic for that trim. GM's LNF turbo-upgrade instructions identify the 2009 Cobalt SS among specific LNF applications. Confirm the engine RPO and installed gearbox; earlier SS cars and other 2.0-litre Ecotec models have different powertrains.

HP Tuners' GM application list groups 2008-10 Cobalt 2.0, 2.2 and 2.4. That listing does not establish every parameter, controller, market or altered vehicle as supported. Record the ECU hardware and software, interface and licence and check the actual calibration with the manufacturer; do not assume support for a swap from the engine name alone.

Factory upgrade kit: sensors and matching calibration

GM Performance Parts instructions for LNF kit 19212670 list two replacement TMAP sensors and a vehicle-specific ECM calibration. The 2009 Cobalt SS is listed separately from other model and transmission combinations. The instructions show replacement of the intake-manifold MAP sensor and the intake-air pressure/temperature sensor, including different connector arrangements. This documented kit illustrates why physical sensor identity, wiring and calibration must match: it is not evidence that every car has the kit or that an arbitrary higher-range sensor can be substituted without correct configuration. GM Performance Parts instruction 19212711.

Manifold and charge-pipe pressure readings

A 2008 Cobalt SS owner with upgraded sensors reported a manifold-pressure display apparently flattening at 255 kPa, and said an HP Tuners channel named "Boost lo-res" reflected a second charge-pipe sensor; the owner asked how to reproduce it in another app. This is a single owner's historical interpretation: the display cap, protocol identifier, exact sensor range and behaviour in current VCM Scanner were not independently verified, and a similar label in another app does not establish an equivalent PID. 2014 Torque forum report.

Compare actual manifold pressure, charge-pipe pressure and local barometric pressure only after confirming what each channel measures and its units. Gauge pressure equals absolute pressure minus barometric pressure at the same measurement point. For illustration, 255 kPa absolute at a location with 100 kPa barometric pressure corresponds to 155 kPa, or about 22.5 psi gauge; different atmospheric pressure changes that result. Manifold and charge-pipe pressures can differ across the throttle and intake tract, so subtracting barometric pressure from charge-pipe pressure does not establish exact manifold boost in every condition.

In an LNF donor-based Goblin kit car, the owner reported confusing boost readings after fitting aftermarket sensors and found that the two sensors had been placed in the wrong locations; boost was later restored, though a separate smoke/compression issue was also observed. This is a modified swap, not a factory Cobalt diagnostic. Do not generalise its connector arrangement or conclude that moving sensors will repair another vehicle; check the exact kit, wiring and sensor transfer function against the supplier and the car's calibration. LNF donor-based Goblin kit-car report.

Record a useful VCM Scanner baseline

Record DTCs and symptoms before reading; HP Tuners says that reading a vehicle clears codes. Save the supported vehicle's original file, record its ECU and calibration identification, fuel, intake, turbo, sensors, exhaust and fuel-system changes. HP Tuners: getting started with VCM Editor. Configure channels that the actual vehicle and software expose: rpm, pedal and throttle, ambient/barometric pressure, desired and measured boost or manifold/charge pressure, intake temperature, requested and actual fuel-rail pressure, timing, knock-related channels and mixture. Distinguish commanded from measured values, validate units and measurement locations, and select a manageable channel set for adequate sample rate. A layout does not automatically add channels. HP Tuners: Scanner layouts. Compare requested and actual rail pressure and independently verified mixture on the same time trace. Check the low-pressure supply and high-pressure direct-injection system separately if supported and if service information calls for it. A smooth rail trace or single pressure reading alone does not prove injector delivery, fuel supply capacity or combustion mixture; use the correct service procedure and equipment. Investigate leaks, sensor and actuator connections, fuel delivery and mechanical condition before changing airflow, fuel or boost calibration. Preserve torque, knock and overboost protections. Make a documented change only where its definition and effects are known, then compare a fresh log with the baseline.

Other LNF owner observations

An owner of an LNF-powered Goblin reported hesitation and a gauge/scan discrepancy, then recorded desired and actual boost and rail pressure with HP Tuners; the independent wideband was not yet wired in. The case illustrates why a rail-pressure trace is not a substitute for measured mixture; its values and suspected causes are not diagnostic targets or proof of a fix for a Cobalt. LNF-powered Goblin overboost report.

A further LNF kit-car owner asked for logs that begin before cranking, with temperature, rpm, cam positions, fuel pressure and injection signals, to diagnose a cold-start problem. The build had several changes, so the symptom does not prove a specific cause. Capturing the start rather than beginning only after warm-up can preserve the transient evidence needed for diagnosis. LNF kit-car cold-start report.

Not established

The cause of the 255 kPa display plateau, the Goblin overboost and the cold-start problem were not determined, and no verified Cobalt-specific sensor definition for HP Tuners is documented.

Related: Chevrolet Cobalt and Cobalt SS models and engines; VCM Scanner; HP Tuners MPVI4.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: Chevrolet Cobalt SS 2.0 LNF: HP Tuners boost and fuel logging

This guide uses the 2009 Chevrolet Cobalt SS Turbo and separately identified LNF-powered kit-car cases to explain HP Tuners pressure logging and direct-injection checks. A forum sensor label or tune from a different vehicle is not a verified definition for the car being worked on.

Identify engine, transmission and controller

Chevrolet's 2009 Cobalt US specification lists a 2.0-litre, 260-hp turbocharged DOHC engine in the SS Turbo coupe and sedan, with a five-speed manual; it does not list the automatic for that trim. GM's LNF turbo-upgrade instructions identify the 2009 Cobalt SS among specific LNF applications. Confirm the engine RPO and installed gearbox; earlier SS cars and other 2.0-litre Ecotec models have different powertrains.

HP Tuners' GM application list groups 2008-10 Cobalt 2.0, 2.2 and 2.4. That listing does not establish every parameter, controller, market or altered vehicle as supported. Record the ECU hardware and software, interface and licence and check the actual calibration with the manufacturer; do not assume support for a swap from the engine name alone.

Factory upgrade kit: sensors and matching calibration

GM Performance Parts instructions for LNF kit 19212670 list two replacement TMAP sensors and a vehicle-specific ECM calibration. The 2009 Cobalt SS is listed separately from other model and transmission combinations. The instructions show replacement of the intake-manifold MAP sensor and the intake-air pressure/temperature sensor, including different connector arrangements. This documented kit illustrates why physical sensor identity, wiring and calibration must match: it is not evidence that every car has the kit or that an arbitrary higher-range sensor can be substituted without correct configuration. GM Performance Parts instruction 19212711.

Manifold and charge-pipe pressure readings

A 2008 Cobalt SS owner with upgraded sensors reported a manifold-pressure display apparently flattening at 255 kPa, and said an HP Tuners channel named "Boost lo-res" reflected a second charge-pipe sensor; the owner asked how to reproduce it in another app. This is a single owner's historical interpretation: the display cap, protocol identifier, exact sensor range and behaviour in current VCM Scanner were not independently verified, and a similar label in another app does not establish an equivalent PID. 2014 Torque forum report.

Compare actual manifold pressure, charge-pipe pressure and local barometric pressure only after confirming what each channel measures and its units. Gauge pressure equals absolute pressure minus barometric pressure at the same measurement point. For illustration, 255 kPa absolute at a location with 100 kPa barometric pressure corresponds to 155 kPa, or about 22.5 psi gauge; different atmospheric pressure changes that result. Manifold and charge-pipe pressures can differ across the throttle and intake tract, so subtracting barometric pressure from charge-pipe pressure does not establish exact manifold boost in every condition.

In an LNF donor-based Goblin kit car, the owner reported confusing boost readings after fitting aftermarket sensors and found that the two sensors had been placed in the wrong locations; boost was later restored, though a separate smoke/compression issue was also observed. This is a modified swap, not a factory Cobalt diagnostic. Do not generalise its connector arrangement or conclude that moving sensors will repair another vehicle; check the exact kit, wiring and sensor transfer function against the supplier and the car's calibration. LNF donor-based Goblin kit-car report.

Record a useful VCM Scanner baseline

  1. Record DTCs and symptoms before reading; HP Tuners says that reading a vehicle clears codes. Save the supported vehicle's original file, record its ECU and calibration identification, fuel, intake, turbo, sensors, exhaust and fuel-system changes. HP Tuners: getting started with VCM Editor.
  2. Configure channels that the actual vehicle and software expose: rpm, pedal and throttle, ambient/barometric pressure, desired and measured boost or manifold/charge pressure, intake temperature, requested and actual fuel-rail pressure, timing, knock-related channels and mixture. Distinguish commanded from measured values, validate units and measurement locations, and select a manageable channel set for adequate sample rate. A layout does not automatically add channels. HP Tuners: Scanner layouts.
  3. Compare requested and actual rail pressure and independently verified mixture on the same time trace. Check the low-pressure supply and high-pressure direct-injection system separately if supported and if service information calls for it. A smooth rail trace or single pressure reading alone does not prove injector delivery, fuel supply capacity or combustion mixture; use the correct service procedure and equipment.
  4. Investigate leaks, sensor and actuator connections, fuel delivery and mechanical condition before changing airflow, fuel or boost calibration. Preserve torque, knock and overboost protections. Make a documented change only where its definition and effects are known, then compare a fresh log with the baseline.

Other LNF owner observations

An owner of an LNF-powered Goblin reported hesitation and a gauge/scan discrepancy, then recorded desired and actual boost and rail pressure with HP Tuners; the independent wideband was not yet wired in. The case illustrates why a rail-pressure trace is not a substitute for measured mixture; its values and suspected causes are not diagnostic targets or proof of a fix for a Cobalt. LNF-powered Goblin overboost report.

A further LNF kit-car owner asked for logs that begin before cranking, with temperature, rpm, cam positions, fuel pressure and injection signals, to diagnose a cold-start problem. The build had several changes, so the symptom does not prove a specific cause. Capturing the start rather than beginning only after warm-up can preserve the transient evidence needed for diagnosis. LNF kit-car cold-start report.

Not established

The cause of the 255 kPa display plateau, the Goblin overboost and the cold-start problem were not determined, and no verified Cobalt-specific sensor definition for HP Tuners is documented.

Related: Chevrolet Cobalt and Cobalt SS models and engines; VCM Scanner; HP Tuners MPVI4.

Revision 2: Chevrolet Cobalt SS 2.0 LNF: HP Tuners boost and fuel logging

This guide uses the 2009 Chevrolet Cobalt SS Turbo and separately identified LNF-powered kit-car cases to explain HP Tuners pressure logging and direct-injection checks. A forum sensor label or tune from a different vehicle is not a verified definition for the car being worked on.

Identify engine, transmission and controller

Chevrolet's 2009 Cobalt US specification lists a 2.0-litre, 260-hp turbocharged DOHC engine in the SS Turbo coupe and sedan, with a five-speed manual; it does not list the automatic for that trim. GM's LNF turbo-upgrade instructions identify the 2009 Cobalt SS among specific LNF applications. Confirm the engine RPO and installed gearbox; earlier SS cars and other 2.0-litre Ecotec models have different powertrains.

HP Tuners' GM application list groups 2008-10 Cobalt 2.0, 2.2 and 2.4. That listing does not establish every parameter, controller, market or altered vehicle as supported. Record the ECU hardware and software, interface and licence and check the actual calibration with the manufacturer; do not assume support for a swap from the engine name alone.

Factory upgrade kit: sensors and matching calibration

GM Performance Parts instructions for LNF kit 19212670 list two replacement TMAP sensors and a vehicle-specific ECM calibration. The 2009 Cobalt SS is listed separately from other model and transmission combinations. The instructions show replacement of the intake-manifold MAP sensor and the intake-air pressure/temperature sensor, including different connector arrangements. This documented kit illustrates why physical sensor identity, wiring and calibration must match: it is not evidence that every car has the kit or that an arbitrary higher-range sensor can be substituted without correct configuration. GM Performance Parts instruction 19212711.

Manifold and charge-pipe pressure readings

A 2008 Cobalt SS owner with upgraded sensors reported a manifold-pressure display apparently flattening at 255 kPa, and said an HP Tuners channel named "Boost lo-res" reflected a second charge-pipe sensor; the owner asked how to reproduce it in another app. This is a single owner's historical interpretation: the display cap, protocol identifier, exact sensor range and behaviour in current VCM Scanner were not independently verified, and a similar label in another app does not establish an equivalent PID. 2014 Torque forum report.

Compare actual manifold pressure, charge-pipe pressure and local barometric pressure only after confirming what each channel measures and its units. Gauge pressure equals absolute pressure minus barometric pressure at the same measurement point. For illustration, 255 kPa absolute at a location with 100 kPa barometric pressure corresponds to 155 kPa, or about 22.5 psi gauge; different atmospheric pressure changes that result. Manifold and charge-pipe pressures can differ across the throttle and intake tract, so subtracting barometric pressure from charge-pipe pressure does not establish exact manifold boost in every condition.

In an LNF donor-based Goblin kit car, the owner reported confusing boost readings after fitting aftermarket sensors and found that the two sensors had been placed in the wrong locations; boost was later restored, though a separate smoke/compression issue was also observed. This is a modified swap, not a factory Cobalt diagnostic. Do not generalise its connector arrangement or conclude that moving sensors will repair another vehicle; check the exact kit, wiring and sensor transfer function against the supplier and the car's calibration. LNF donor-based Goblin kit-car report.

Record a useful VCM Scanner baseline

  1. Record DTCs and symptoms before reading; HP Tuners says that reading a vehicle clears codes. Save the supported vehicle's original file, record its ECU and calibration identification, fuel, intake, turbo, sensors, exhaust and fuel-system changes. HP Tuners: getting started with VCM Editor.
  2. Configure channels that the actual vehicle and software expose: rpm, pedal and throttle, ambient/barometric pressure, desired and measured boost or manifold/charge pressure, intake temperature, requested and actual fuel-rail pressure, timing, knock-related channels and mixture. Distinguish commanded from measured values, validate units and measurement locations, and select a manageable channel set for adequate sample rate. A layout does not automatically add channels. HP Tuners: Scanner layouts.
  3. Compare requested and actual rail pressure and independently verified mixture on the same time trace. Check the low-pressure supply and high-pressure direct-injection system separately if supported and if service information calls for it. A smooth rail trace or single pressure reading alone does not prove injector delivery, fuel supply capacity or combustion mixture; use the correct service procedure and equipment.
  4. Investigate leaks, sensor and actuator connections, fuel delivery and mechanical condition before changing airflow, fuel or boost calibration. Preserve torque, knock and overboost protections. Make a documented change only where its definition and effects are known, then compare a fresh log with the baseline.

Other LNF owner observations

An owner of an LNF-powered Goblin reported hesitation and a gauge/scan discrepancy, then recorded desired and actual boost and rail pressure with HP Tuners; the independent wideband was not yet wired in. The case illustrates why a rail-pressure trace is not a substitute for measured mixture; its values and suspected causes are not diagnostic targets or proof of a fix for a Cobalt. LNF-powered Goblin overboost report.

A further LNF kit-car owner asked for logs that begin before cranking, with temperature, rpm, cam positions, fuel pressure and injection signals, to diagnose a cold-start problem. The build had several changes, so the symptom does not prove a specific cause. Capturing the start rather than beginning only after warm-up can preserve the transient evidence needed for diagnosis. LNF kit-car cold-start report.

Not established

The cause of the 255 kPa display plateau, the Goblin overboost and the cold-start problem were not determined, and no verified Cobalt-specific sensor definition for HP Tuners is documented.

Related: Chevrolet Cobalt and Cobalt SS models and engines; VCM Scanner; HP Tuners MPVI4.