Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Performance
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 2

Removed text is struck through; added text is highlighted.

Fuel system upgrades explains why fuel mass must follow air mass. This page covers the supply hardware that carries it: the pump, regulator, filters, lines and wiring. The figures below are worked examples from high-power V8 builds, not specifications for any engine.Fuel system upgrades explains why fuel mass must follow air mass. This page covers the supply hardware that carries it: the pump, regulator, filters, lines and wiring. The figures below are examples from two engine-builder and tuner articles about high-power V8 builds, not specifications for any engine.

Flow depends on pressure and voltage

A pump's catalogue flow is quoted at a stated pressure and voltage, and it falls when either condition gets worse. Flow rises with supply voltage and falls as system pressure rises. For one 255 L/h pump rated at 13 V, flow is noticeably higher at a higher supply voltage, and a rise from 50 to 60 psi cuts flow by about 6 to 7 per cent (Kenne Bell: Pump You Up). A pump should therefore be sized to total fuel pressure, base pressure plus boost, and its flow and current draw confirmed at operating pressure rather than at the advertised figure (Dragzine: True SStreet).In the Dragzine build, a 1,025 hp car called for a pump rated at a minimum of 180 gph at 80 psi, drawing about 20 amps. The supply wiring has to carry that current. Switching on lights and accessories can lower pump voltage; on one supercharged engine that moved the air-fuel ratio by more than half a point. Speaker wire will not do for a large pump.A pump's catalogue flow is quoted at a stated pressure and voltage, and it falls when either condition gets worse. Kenne Bell's Richard Holdener writes that flow rises with supply voltage and falls as system pressure rises; his example is a 255 L/h pump at 13 V that flows noticeably more at higher voltage, and a rise from 50 to 60 psi cuts flow by 6 to 7 per cent for the same pump. Dragzine's article on a 1,025 hp street and strip Camaro makes the same point: the pump builder's advice is to size to total fuel pressure, base pressure plus boost, and to confirm flow and current draw at operating pressure, not at the advertised figure.In that article, the Weldon pump used was specified at a minimum of 180 gph at 80 psi and drew about 20 amps. Check the supply wiring can carry that current. Holdener notes that turning on lights and accessories can lower pump voltage, and that on one supercharged engine he saw the air-fuel ratio move by more than half a point from lights and a stereo. He warns that speaker wire will not do for a large pump.

Return and non-return systems

The two layouts regulate pressure differently. A return-style system runs the pump at maximum flow and holds pressure by bypassing the excess fuel back to the tank. A non-return system varies the pump's voltage, using a rail pressure sensor and the computer, so the pump only supplies what is needed. That changes how an upgrade should be done: on a non-return system the controller is part of the supply, and a pump uprate must still work with it. The Dragzine example covers only a return-style bypass regulator.Circulating unused fuel warms the tank. Warm fuel can boil and cause vapour lock and erratic pressure, and an oversized system runs hotter, which can lead to cavitation and pump failure. Size the system for realistic engine output rather than the largest pump available.Holdener describes how the two layouts differ. A return-style system runs the pump at maximum flow and regulates pressure by bypassing the excess fuel back to the tank. A non-return system varies the pump's voltage, using a rail pressure sensor and the computer, and the pump only supplies what is needed. That changes how an upgrade should be done: a pump uprate on a non-return system must still work with the controller, and the controller, not just the pump, is part of the supply. The Dragzine article covers only a return-style bypass regulator and does not discuss non-return systems.The same article notes that continually circulating unused fuel warms the tank, that warm fuel can boil and cause vapour lock and erratic pressure, and that an oversized system runs hotter, which can cause cavitation and pump failure. The pump builder's advice is to match the system to realistic engine output rather than to oversize it.

Regulators and boost

A boosted application needs fuel pressure to rise roughly one to one with boost, so that the pressure difference across the injectors stays constant: 50 psi of fuel pressure with 10 psi of boost gives a 40 psi difference. Plumbing, rail and fittings cost pressure too; one test measured about 7.5 psi lost between the pump outlet and the rail. In the Dragzine build, a typical base pressure was 40 to 60 psi, and the bypass return orifice was kept at 0.250 in or more for about 200 gph, and not below 0.200 in, or the regulator becomes the restriction. See fuel system upgrades for fuel management units and petrol port-injector calibration for how injector flow changes with pressure.Holdener says a boosted application needs fuel pressure to rise roughly one to one with boost, to hold the pressure difference across the injectors: for example, 50 psi of fuel pressure with 10 psi of boost gives a 40 psi difference. In his test, the plumbing, fuel rail and fittings cost about 7.5 psi between the pump outlet and the rail. The Dragzine example uses an adjustable return regulator with a boost reference port; typical base pressure on fuel-injected engines is 40 to 60 psi in that article, and it advises a return orifice of at least 0.250 in for about 200 gph, and not under 0.200 in, or the regulator becomes a restriction. See fuel system upgrades for fuel management units and petrol port-injector calibration for how injector flow changes with pressure.

Lines, filters and fittings

Line size. The Dragzine build used -10 AN lines for about 200 gph and -12 AN above that, with smaller sizes after the filter. An undersized inlet line or a restrictive filter can overload a pump that is itself adequate. Hose and fittings. Match them to the fuel. Methanol and E85 need PTFE-style hose, and bare aluminium fittings corrode with oxygenated fuels. See E85, ethanol and flex fuel. Pump position. An in-tank pump is limited by the space in the pump assembly. Inline pumps can be added without dropping the tank but add noise, and with two pumps the lower-flow one limits the system. Ethanol allowance. The builder of that car adds 30 to 40 per cent to the flow calculation for E85 or straight ethanol, and 30 to 35 per cent as a margin for losses and future upgrades. Those are allowances for that build.Line size. The Dragzine build used -10 AN lines for about 200 gph and -12 AN above that, with smaller sizes after the filter. An undersized inlet line or a restrictive filter can overload a pump that is itself adequate; its example is a fine filter choking a larger line. Hose and fittings. Match them to the fuel. The article says methanol and E85 need PTFE-style hose, and warns against bare aluminium fittings with oxygenated fuels because of corrosion. See E85, ethanol and flex fuel. Pump position. Holdener notes that an in-tank pump is limited by the space in the assembly, that inline pumps can be added without dropping the tank but bring noise concerns, and that with two pumps the lower-flow pump limits the system. Ethanol allowance. The pump builder adds 30 to 40 per cent to the flow calculation for E85 or straight ethanol, and 30 to 35 per cent as a margin for losses and future upgrades. Those are his figures for his builds.

Checking the system

Log fuel pressure and, where possible, pump voltage at full load, not just at idle, with the accessories on that will be used. Compare the pressure difference across the injectors to its target at maximum boost. A falling difference as boost rises means the pump, regulator or lines cannot keep up. Check the mixture with a wideband sensor (air-fuel ratio and wideband lambda sensors) and look for a lean spot at the top of the rev range, which is where a weak supply shows first. Inspect for leaks and heat damage after testing. Fuel under pressure is a fire risk, so use proper fittings and secure the lines.

Direct-injection engines have a separate high-pressure pump and rail, so the port-injection rules above describe only the low-pressure side: EA113 and EA888 fuel pump upgrade comparison and injector upgrade comparison are model-specific examples.

Sources

True SStreet: The Science Behind Street/Strip Fuel Systems. Andrew Wolf, Dragzine, 31 July 2019, with Weldon Racing. Pump sizing to total pressure, return orifice, line sizes and fuel heating. Accessed 2026-11-19. Pump You Up. Richard Holdener, Kenne Bell, 1 October 2012 (updated 26 September 2022). Flow against voltage and pressure, regulators and wiring. Published by a supercharger and fuel-pump voltage-booster maker. Accessed 2026-11-19.True SStreet: The Science Behind Street/Strip Fuel Systems. Andrew Wolf, Dragzine, 31 July 2019, with Weldon Racing. Pump sizing to total pressure, return orifice, line sizes and fuel heating. Accessed 2026-11-19. Pump You Up. Richard Holdener, Kenne Bell, 1 October 2012 (updated 26 September 2022). Flow against voltage and pressure, regulators and wiring. Published by a supercharger and fuel-pump-voltage-booster maker. Accessed 2026-11-19.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Fuel pumps, regulators and lines for higher output

Fuel system upgrades explains why fuel mass must follow air mass. This page covers the supply hardware that carries it: the pump, regulator, filters, lines and wiring. The figures below are examples from two engine-builder and tuner articles about high-power V8 builds, not specifications for any engine.

Flow depends on pressure and voltage

A pump's catalogue flow is quoted at a stated pressure and voltage, and it falls when either condition gets worse. Kenne Bell's Richard Holdener writes that flow rises with supply voltage and falls as system pressure rises; his example is a 255 L/h pump at 13 V that flows noticeably more at higher voltage, and a rise from 50 to 60 psi cuts flow by 6 to 7 per cent for the same pump. Dragzine's article on a 1,025 hp street and strip Camaro makes the same point: the pump builder's advice is to size to total fuel pressure, base pressure plus boost, and to confirm flow and current draw at operating pressure, not at the advertised figure.

In that article, the Weldon pump used was specified at a minimum of 180 gph at 80 psi and drew about 20 amps. Check the supply wiring can carry that current. Holdener notes that turning on lights and accessories can lower pump voltage, and that on one supercharged engine he saw the air-fuel ratio move by more than half a point from lights and a stereo. He warns that speaker wire will not do for a large pump.

Return and non-return systems

Holdener describes how the two layouts differ. A return-style system runs the pump at maximum flow and regulates pressure by bypassing the excess fuel back to the tank. A non-return system varies the pump's voltage, using a rail pressure sensor and the computer, and the pump only supplies what is needed. That changes how an upgrade should be done: a pump uprate on a non-return system must still work with the controller, and the controller, not just the pump, is part of the supply. The Dragzine article covers only a return-style bypass regulator and does not discuss non-return systems.

The same article notes that continually circulating unused fuel warms the tank, that warm fuel can boil and cause vapour lock and erratic pressure, and that an oversized system runs hotter, which can cause cavitation and pump failure. The pump builder's advice is to match the system to realistic engine output rather than to oversize it.

Regulators and boost

Holdener says a boosted application needs fuel pressure to rise roughly one to one with boost, to hold the pressure difference across the injectors: for example, 50 psi of fuel pressure with 10 psi of boost gives a 40 psi difference. In his test, the plumbing, fuel rail and fittings cost about 7.5 psi between the pump outlet and the rail. The Dragzine example uses an adjustable return regulator with a boost reference port; typical base pressure on fuel-injected engines is 40 to 60 psi in that article, and it advises a return orifice of at least 0.250 in for about 200 gph, and not under 0.200 in, or the regulator becomes a restriction. See fuel system upgrades for fuel management units and petrol port-injector calibration for how injector flow changes with pressure.

Lines, filters and fittings

  • Line size. The Dragzine build used -10 AN lines for about 200 gph and -12 AN above that, with smaller sizes after the filter. An undersized inlet line or a restrictive filter can overload a pump that is itself adequate; its example is a fine filter choking a larger line.
  • Hose and fittings. Match them to the fuel. The article says methanol and E85 need PTFE-style hose, and warns against bare aluminium fittings with oxygenated fuels because of corrosion. See E85, ethanol and flex fuel.
  • Pump position. Holdener notes that an in-tank pump is limited by the space in the assembly, that inline pumps can be added without dropping the tank but bring noise concerns, and that with two pumps the lower-flow pump limits the system.
  • Ethanol allowance. The pump builder adds 30 to 40 per cent to the flow calculation for E85 or straight ethanol, and 30 to 35 per cent as a margin for losses and future upgrades. Those are his figures for his builds.

Checking the system

  1. Log fuel pressure and, where possible, pump voltage at full load, not just at idle, with the accessories on that will be used.
  2. Compare the pressure difference across the injectors to its target at maximum boost. A falling difference as boost rises means the pump, regulator or lines cannot keep up.
  3. Check the mixture with a wideband sensor (air-fuel ratio and wideband lambda sensors) and look for a lean spot at the top of the rev range, which is where a weak supply shows first.
  4. Inspect for leaks and heat damage after testing. Fuel under pressure is a fire risk, so use proper fittings and secure the lines.

Direct-injection engines have a separate high-pressure pump and rail, so the port-injection rules above describe only the low-pressure side: EA113 and EA888 fuel pump upgrade comparison and injector upgrade comparison are model-specific examples.

Sources

  • True SStreet: The Science Behind Street/Strip Fuel Systems. Andrew Wolf, Dragzine, 31 July 2019, with Weldon Racing. Pump sizing to total pressure, return orifice, line sizes and fuel heating. Accessed 2026-11-19.
  • Pump You Up. Richard Holdener, Kenne Bell, 1 October 2012 (updated 26 September 2022). Flow against voltage and pressure, regulators and wiring. Published by a supercharger and fuel-pump-voltage-booster maker. Accessed 2026-11-19.
Revision 2: Fuel pumps, regulators and lines for higher output

Fuel system upgrades explains why fuel mass must follow air mass. This page covers the supply hardware that carries it: the pump, regulator, filters, lines and wiring. The figures below are worked examples from high-power V8 builds, not specifications for any engine.

Flow depends on pressure and voltage

A pump's catalogue flow is quoted at a stated pressure and voltage, and it falls when either condition gets worse. Flow rises with supply voltage and falls as system pressure rises. For one 255 L/h pump rated at 13 V, flow is noticeably higher at a higher supply voltage, and a rise from 50 to 60 psi cuts flow by about 6 to 7 per cent (Kenne Bell: Pump You Up). A pump should therefore be sized to total fuel pressure, base pressure plus boost, and its flow and current draw confirmed at operating pressure rather than at the advertised figure (Dragzine: True SStreet).

In the Dragzine build, a 1,025 hp car called for a pump rated at a minimum of 180 gph at 80 psi, drawing about 20 amps. The supply wiring has to carry that current. Switching on lights and accessories can lower pump voltage; on one supercharged engine that moved the air-fuel ratio by more than half a point. Speaker wire will not do for a large pump.

Return and non-return systems

The two layouts regulate pressure differently. A return-style system runs the pump at maximum flow and holds pressure by bypassing the excess fuel back to the tank. A non-return system varies the pump's voltage, using a rail pressure sensor and the computer, so the pump only supplies what is needed. That changes how an upgrade should be done: on a non-return system the controller is part of the supply, and a pump uprate must still work with it. The Dragzine example covers only a return-style bypass regulator.

Circulating unused fuel warms the tank. Warm fuel can boil and cause vapour lock and erratic pressure, and an oversized system runs hotter, which can lead to cavitation and pump failure. Size the system for realistic engine output rather than the largest pump available.

Regulators and boost

A boosted application needs fuel pressure to rise roughly one to one with boost, so that the pressure difference across the injectors stays constant: 50 psi of fuel pressure with 10 psi of boost gives a 40 psi difference. Plumbing, rail and fittings cost pressure too; one test measured about 7.5 psi lost between the pump outlet and the rail. In the Dragzine build, a typical base pressure was 40 to 60 psi, and the bypass return orifice was kept at 0.250 in or more for about 200 gph, and not below 0.200 in, or the regulator becomes the restriction. See fuel system upgrades for fuel management units and petrol port-injector calibration for how injector flow changes with pressure.

Lines, filters and fittings

  • Line size. The Dragzine build used -10 AN lines for about 200 gph and -12 AN above that, with smaller sizes after the filter. An undersized inlet line or a restrictive filter can overload a pump that is itself adequate.
  • Hose and fittings. Match them to the fuel. Methanol and E85 need PTFE-style hose, and bare aluminium fittings corrode with oxygenated fuels. See E85, ethanol and flex fuel.
  • Pump position. An in-tank pump is limited by the space in the pump assembly. Inline pumps can be added without dropping the tank but add noise, and with two pumps the lower-flow one limits the system.
  • Ethanol allowance. The builder of that car adds 30 to 40 per cent to the flow calculation for E85 or straight ethanol, and 30 to 35 per cent as a margin for losses and future upgrades. Those are allowances for that build.

Checking the system

  1. Log fuel pressure and, where possible, pump voltage at full load, not just at idle, with the accessories on that will be used.
  2. Compare the pressure difference across the injectors to its target at maximum boost. A falling difference as boost rises means the pump, regulator or lines cannot keep up.
  3. Check the mixture with a wideband sensor (air-fuel ratio and wideband lambda sensors) and look for a lean spot at the top of the rev range, which is where a weak supply shows first.
  4. Inspect for leaks and heat damage after testing. Fuel under pressure is a fire risk, so use proper fittings and secure the lines.

Direct-injection engines have a separate high-pressure pump and rail, so the port-injection rules above describe only the low-pressure side: EA113 and EA888 fuel pump upgrade comparison and injector upgrade comparison are model-specific examples.

Sources

  • True SStreet: The Science Behind Street/Strip Fuel Systems. Andrew Wolf, Dragzine, 31 July 2019, with Weldon Racing. Pump sizing to total pressure, return orifice, line sizes and fuel heating. Accessed 2026-11-19.
  • Pump You Up. Richard Holdener, Kenne Bell, 1 October 2012 (updated 26 September 2022). Flow against voltage and pressure, regulators and wiring. Published by a supercharger and fuel-pump voltage-booster maker. Accessed 2026-11-19.