Fuel system upgrades explains why fuel mass must follow air mass. This page covers the supply hardware that carries it: the pump, regulator, filters, lines and wiring. The figures below are examples from two engine-builder and tuner articles about high-power V8 builds, not specifications for any engine.
Flow depends on pressure and voltage
A pump's catalogue flow is quoted at a stated pressure and voltage, and it falls when either condition gets worse. Kenne Bell's Richard Holdener writes that flow rises with supply voltage and falls as system pressure rises; his example is a 255 L/h pump at 13 V that flows noticeably more at higher voltage, and a rise from 50 to 60 psi cuts flow by 6 to 7 per cent for the same pump. Dragzine's article on a 1,025 hp street and strip Camaro makes the same point: the pump builder's advice is to size to total fuel pressure, base pressure plus boost, and to confirm flow and current draw at operating pressure, not at the advertised figure.
In that article, the Weldon pump used was specified at a minimum of 180 gph at 80 psi and drew about 20 amps. Check the supply wiring can carry that current. Holdener notes that turning on lights and accessories can lower pump voltage, and that on one supercharged engine he saw the air-fuel ratio move by more than half a point from lights and a stereo. He warns that speaker wire will not do for a large pump.
Return and non-return systems
Holdener describes how the two layouts differ. A return-style system runs the pump at maximum flow and regulates pressure by bypassing the excess fuel back to the tank. A non-return system varies the pump's voltage, using a rail pressure sensor and the computer, and the pump only supplies what is needed. That changes how an upgrade should be done: a pump uprate on a non-return system must still work with the controller, and the controller, not just the pump, is part of the supply. The Dragzine article covers only a return-style bypass regulator and does not discuss non-return systems.
The same article notes that continually circulating unused fuel warms the tank, that warm fuel can boil and cause vapour lock and erratic pressure, and that an oversized system runs hotter, which can cause cavitation and pump failure. The pump builder's advice is to match the system to realistic engine output rather than to oversize it.
Regulators and boost
Holdener says a boosted application needs fuel pressure to rise roughly one to one with boost, to hold the pressure difference across the injectors: for example, 50 psi of fuel pressure with 10 psi of boost gives a 40 psi difference. In his test, the plumbing, fuel rail and fittings cost about 7.5 psi between the pump outlet and the rail. The Dragzine example uses an adjustable return regulator with a boost reference port; typical base pressure on fuel-injected engines is 40 to 60 psi in that article, and it advises a return orifice of at least 0.250 in for about 200 gph, and not under 0.200 in, or the regulator becomes a restriction. See fuel system upgrades for fuel management units and petrol port-injector calibration for how injector flow changes with pressure.
Lines, filters and fittings
- Line size. The Dragzine build used -10 AN lines for about 200 gph and -12 AN above that, with smaller sizes after the filter. An undersized inlet line or a restrictive filter can overload a pump that is itself adequate; its example is a fine filter choking a larger line.
- Hose and fittings. Match them to the fuel. The article says methanol and E85 need PTFE-style hose, and warns against bare aluminium fittings with oxygenated fuels because of corrosion. See E85, ethanol and flex fuel.
- Pump position. Holdener notes that an in-tank pump is limited by the space in the assembly, that inline pumps can be added without dropping the tank but bring noise concerns, and that with two pumps the lower-flow pump limits the system.
- Ethanol allowance. The pump builder adds 30 to 40 per cent to the flow calculation for E85 or straight ethanol, and 30 to 35 per cent as a margin for losses and future upgrades. Those are his figures for his builds.
Checking the system
- Log fuel pressure and, where possible, pump voltage at full load, not just at idle, with the accessories on that will be used.
- Compare the pressure difference across the injectors to its target at maximum boost. A falling difference as boost rises means the pump, regulator or lines cannot keep up.
- Check the mixture with a wideband sensor (air-fuel ratio and wideband lambda sensors) and look for a lean spot at the top of the rev range, which is where a weak supply shows first.
- Inspect for leaks and heat damage after testing. Fuel under pressure is a fire risk, so use proper fittings and secure the lines.
Direct-injection engines have a separate high-pressure pump and rail, so the port-injection rules above describe only the low-pressure side: EA113 and EA888 fuel pump upgrade comparison and injector upgrade comparison are model-specific examples.
Sources
- True SStreet: The Science Behind Street/Strip Fuel Systems. Andrew Wolf, Dragzine, 31 July 2019, with Weldon Racing. Pump sizing to total pressure, return orifice, line sizes and fuel heating. Accessed 2026-11-19.
- Pump You Up. Richard Holdener, Kenne Bell, 1 October 2012 (updated 26 September 2022). Flow against voltage and pressure, regulators and wiring. Published by a supercharger and fuel-pump-voltage-booster maker. Accessed 2026-11-19.