Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Audi, SEAT, Škoda, Volkswagen

Scope and how to read the figures

These are documented examples of Volkswagen Group 1.9-litre eight-valve PD (unit-injector) builds, not guaranteed stage recipes. The figures and component lists are reported by the builders; dyno method, correction and wheel-versus-crank basis are not established consistently by the project pages. A car may have changed since it was photographed. Nitrous-assisted results are marked separately from the reported diesel-only results.

Identify the actual engine, injector body and ECU before ordering parts. For injector numbers, nozzle references, delivery and timing checks, see PD injection and nozzle identification.

Around 250 bhp: Ibiza ATD

Rear view of the red Darkside Ibiza ATD project

Image: Darkside Developments, Ibiza ATD project gallery. Reproduced with user-stated permission.

Reported: 249.8 bhp and 430 lb ft (584 Nm); 1.9 PD ATD, HDS 02M six-speed. Darkside lists its Hybrid Killer turbo, PD injectors with Firad 50% nozzles, SeatSport intercooler and pipework, PD150 inlet and head bolts, and custom calibration. The project also lists a single-mass flywheel, sintered clutch and Quaife limited-slip differential. Rods and bottom-end specification are not stated. Builder's specification.

Approaching 300 bhp: Ibiza ASZ

Grey Ibiza ASZ on the Darkside dynamometer

Image: Darkside Developments, Ibiza ASZ project gallery. Reproduced with user-stated permission.

Reported: 287 bhp and 430 lb ft (584 Nm); 1.9 PD ASZ and FSM 02M six-speed. The listed combination includes a GTB2260VK turbo kit, PD injectors with Firad 100% nozzles, race cam, PD150 head bolts, custom intake, front-mounted intercooler and custom remap. Transmission work includes a single-mass flywheel and organic clutch, Quaife differential and selector reinforcement. The page does not establish a complete bottom-end specification. Builder's specification.

300–450 bhp: Bora ASZ, diesel-only and nitrous

Bora ASZ project engine on a stand during assembly

Image: Darkside Developments, Bora ASZ project gallery. Reproduced with user-stated permission. The build-stage image does not establish the configuration at every recorded run.

Reported: 326 bhp and 420 lb ft (570 Nm) diesel-only; 449 bhp and 580 lb ft (787 Nm) with nitrous. Darkside identifies an ASZ-based 1.9 PD with GTD2872VRK billet hybrid turbo, Firad +160% PD nozzles, ported head, oversized valves, race cam, head and main studs, Rosten H-beam rods and machined BHW pistons. It also lists an intercooler, FASS lift-pump kit, oil cooling, water injection, a dry nitrous kit and custom remap. This is a highly modified example, not evidence that the same result is available without nitrous. Builder's current project page.

340–450 bhp: Ibiza BLT drag build

Engine bay of the Ibiza BLT PD drag project

Image: Darkside Developments, Ibiza BLT project gallery. Reproduced with user-stated permission. The photo may show a different build stage.

Reported: 343.7 bhp and 405 lb ft (550 Nm) without nitrous; 451.1 bhp and 560 lb ft (760 Nm) with nitrous. The listed BLT-based build uses a Holset HX turbo, Firad +160% PD nozzles, ported head, oversize valves, uprated springs, race cam, head studs and machined coated pistons, plus intercooling, water injection and custom mapping. The 02M transmission has a solid input shaft, sintered clutch, plated differential and reinforcement. Darkside reports a 10.64-second quarter mile; it is a drag-oriented build and does not document con-rod specification on this project page. Builder's project and previous specifications.

What the examples do and do not prove

  • Air and fuel work together. The listed builds combine turbo, charge cooling, injector/nozzle selection and calibration. A nozzle percentage is a supplier designation, not a guaranteed gain or a universal duration setting.
  • Inspect the baseline. Check compression, oil supply and condition, cam lobes, injector bores, fuel delivery and cooling before relying on upgraded hardware; investigate existing faults first.
  • Engine and drivetrain are a system. The examples show different head, bottom-end, clutch, differential and gearbox choices. The presence of a part on one car does not prove it is mandatory or durable at the same output on another.
  • Use measured evidence. Retain injector bench sheets, dyno graphs and test conditions, and log relevant pressure, temperature and fueling channels for the actual ECU. Compare diesel-only and assisted runs separately; torque and its rpm range matter alongside peak power.
  • Fitment and use: application differences, emissions equipment and local road rules matter. Follow the relevant repair procedures and validate the whole vehicle for its intended use.

Photographs and project specifications are attributed to Darkside Developments. Image reuse permission was stated by the user; no separate licence terms were supplied. Research reviewed 18 November 2026.